296. Compute for the torsional deflection in degrees of a 110 mm diameter, 1.4 m long shaft subjected to a twisting moment of 3 x 106 N-mm. The torsional modulus of elasticity is 8300o N/mm2 A. 0.27 B. 0.31 C. 0.20 d. 0.24 A View Answer: Answer: Option C Explanation: 297. Find the torsional moment (in Newton-mm) developed when the shaft delivers 20 kw at 200 rpm

296. Compute for the torsional deflection in degrees of a 110 mm diameter, 1.4 m long shaft subjected to a twisting moment of 3 x 106 N-mm. The torsional modulus of elasticity is 8300o N/mm2 A. 0.27 B. 0.31 C. 0.20 d. 0.24 A View Answer: Answer: Option C Explanation: 297. Find the torsional moment (in Newton-mm) developed when the shaft delivers 20 kw at 200 rpm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

47 d lameters H. WOA vod Consists of three bars of unequal as shown in fig., find the stress in each bar and the C langation off the rood ? use E= 200GVa %3D -30mm =20mm 20W At B 1.5m 2.5m 2m
Draw axial,shear force and bending miment digram fig 1and 2 10 ANm 20 AN | 20 k 1.5 m 1.5 m Figure (1) 70 kN 70 kN -20 kN/m 25 m 2.5 m 2.5 m Figure (2)
Exse Analyze the frame shown using consistent defor. method Cassume redundants are CX and Cy I constart The Frame is Indet.. to the 2nd degree 4m 6x 8x 5oky To kN/m 5m C * -X₁
47 H.WOA rod Consists of three bars af unequal dlameters as shown in fig., find the Stress in each bar and the C longation of the rood ?_use E= 200GPA %3D =30mm =20 mm 1.5m 2.5m 2m
2. Assume that a 20mmØ rivet joins the plates that are each 110mm wide. The allowable stresses are 120 MPa for bearing in the plate material and 60MPA for shearing of rivet. Determine the minimum thickness of each plate 110 mm 20-mm 0
1- The floor beam in Fig. below supports nonstructural elements not likely to be damaged by large deflections. If the service dead load equals 21 kN/m and the service live load equals 12 kN/m, does the 450 mm beam satisfy ACI Code requirements for allowable 400 mm deflections? f = 25 MPa, fy= 400 MPa. SØ25 mm %3D 75 mm
4Iven: Ex : -533 x10 Ex: -533 x/0-6 67x10-6 Yx, = -l626 x /0-b E : 30 x/0 psi Y: ,30 Find: Stress Components on face +45° from X -axis.
By least work and constant deformation method both Need method for deflection calculation not table
Problem 14 , 3 parts ....plz solve all parts I vll upvote
Determine the principal stresses acting at the 1 section using Mohr circle 150mm 5mm 5kN 60° 180mm 6mm 8mm 2 m 3 m 3 m 200mm
Now, compute the moment of inertia about the weak-axis. Work smarter, not harder: will you choose an additive method or a subtractive method? a b b I C---- WEAK AXIS I+I Ans: 13.9 inª
pls help ASAP absolute value of torential sheer stress of the hollow steel Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 8o N-m Sm steel Iel tiraler dhmmum Selid circalor D= 75 my D 8o mm G GA G 1S0 EP