3/ Liquid of density 1200 kg/m² throsh a pipe оf бошт нифере intemal dimeter. an orifice, lo mm in dimeter is fitted in the life and differential Pressure Shwn on amercury manometer is 0-1 m. assuming the leads the manometer are filled with the flowing fluid, calculate the mass flow fate of fluid flowing the approximate drop in pressure caused by the orifice in KN/m³ pe of 50 d differen the flowi ifice in the de ba We the coefficient of discharge maybe taken as 0-81 and the density of mercury is 13,550 kg/m³

3/ Liquid of density 1200 kg/m² throsh a pipe оf бошт нифере intemal dimeter. an orifice, lo mm in dimeter is fitted in the life and differential Pressure Shwn on amercury manometer is 0-1 m. assuming the leads the manometer are filled with the flowing fluid, calculate the mass flow fate of fluid flowing the approximate drop in pressure caused by the orifice in KN/m³ pe of 50 d differen the flowi ifice in the de ba We the coefficient of discharge maybe taken as 0-81 and the density of mercury is 13,550 kg/m³

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Similar questions

Plot curves on a single plot that display the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure as 0 to ~1 MPa). Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
On a single plot, show curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure should be 0 to ~1 MPa). Pipe inner diameter: 0.03 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
liquid pentane with relative density 0.62, 20 °c as shown in the figure at temperature, the geyç pressure is 0.2 atm dollars a cast iron (0.2 m odiameter cast iron)) it flows through the pipe.Marked as full pipe output it can be considered as the principal atmospheric pressure at the point at which it is. The total pipe length in the system is 45 m.5 kW in the system there is a pump that works with 92% efficiency in its power. Liquid since the volumetric flow rate of pentane is 0.05 m2 / s, with the tank calculate the height difference botween the pipe output. Data: * Friction loss at the pump is negligible. Gryc Atark purmp
Explain the velocity and pressure behavior of the fluid through venturi. Also explain how to measure these parameters and give physical significance of venture.
Fluid is moving at rate of 3m/s in a chamber of a 12inch positive displacement flow meter, if the density of the fluid is 4.5kg/m³ and has a mass flow rate of 8kg/s, what is the maximum volume capacity of the chamber?
EX in Asteel of speçific weight cy lin der (1"diametar andiz" Long) (8) =490 1b fI Ft3 fall be Cause of its own weight, at q uniform slig htly 9. rate of on5 HIs in side a tube of larger diameter.A Castor- oil film M = 6x lo -3 16 between t-s Constant thihness and the tube between of %3D is the cylinder Determine the cleamanCe (y) in ft the Cylinder and the tube-
Water flows thiough a horizontal pipe at o veiociy of 50 ft per secon d. Owing to the pipe gradually expanding to larger rize, the velocity decreases to 35 f1 per second, what i the differentce between the prewures at two points, one in each size of pipe ? Given : VA =(50fps Ve -35 fps 1,421.88 psf 1,165.15 psf O 1,345.11 psf 1,021.96 psf 1,236.75 psf
As an engineer, you are setting up an experiment to measure the airflow rate in a duct. Choose a technique and devices for the measurement. You are required to design/draw the set-up and demonstrate the calculation for themeasurement of flow rate. Please discuss the relevant principle involved and reason for selectingthe technique.
The pressure of a reactor vessel can be adjusted bychanging either the inlet or outlet gaseous flow rate. Theoutlet flow is kept fixed as long as the tank pressure remainsbetween 100 and 120 psi, and pressure changes are treatedby manipulating the inlet flow control valve. However, if thepressure goes higher than these limits, the exit gas flow isthen changed. Finally, if the pressure exceeds 200 psi, a ventvalve on the vessel is opened and transfers the gas to a storagevessel. Design a control scheme that meets the performanceobjectives. Draw a process instrumentation diagram for theresulting control system
Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
The thrust of a shaft is taken by a collar bearing provided with a forced The lubrication system maintains a film of oil of lubrication system. orm thickness between the surface of the collar and the bearing The mal and intemal diameters of collar are 16 and 12 cms. respectively. The thickness of oil film is 0.02 ems. and coefficient of viscosity is 0.91 naise. Find the horse-power lost in overcoming friction: when the shaft is notated at a speed of 350 E.p.m. Skult
H.W. Petroleum oil (sp. gr. = 0.9 and viscosity = 13 CP) flows isothermally through a horizontal 5 cm pipe. A Pitot tube is inserted at the centre of a pipe and its leads are filled with the same oil and attached to a U-tube containing water. The reading on the manometer is 10 cm. Calculate the volumetric flow of oil in m/s. The co-efficient of Pitot tube is