3. A dc motor develops 150 N-m and 50 N-m of torque at a speed of 250 rad/s and 750 rad/s respectively when 100 volts are applied. Find the following transfer function G(5) = 0₂ (5) Ea (5) J= 1kg-m² J₂ = 2kg⋅m² J₂ = 2ky. m² Jr = 16 lag. m² D= 32·N·m-s/rad and N₁=10 N₂= 20 №3= 10 N₁ = 10 8, (t) N₁ Na falt) + J 1604 lat) Moton N₂ D When La «Ra J₂ B Jo

3. A dc motor develops 150 N-m and 50 N-m of torque at a speed of 250 rad/s and 750 rad/s respectively when 100 volts are applied. Find the following transfer function G(5) = 0₂ (5) Ea (5) J= 1kg-m² J₂ = 2kg⋅m² J₂ = 2ky. m² Jr = 16 lag. m² D= 32·N·m-s/rad and N₁=10 N₂= 20 №3= 10 N₁ = 10 8, (t) N₁ Na falt) + J 1604 lat) Moton N₂ D When La «Ra J₂ B Jo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The field windings of a series motor have a resistance of 120 ohms at 15 o C. After running for two hours, the resistance increases to 140 ohms. If the temp. coefficient at 15 deg C is -0.00427, find the temp. rise.
nid%3D11610 This course O d. Flux = 0.9 Wb, Speed = 473 rad/sec Clear my choice In a given DC motor, the output power is 20 HP, and the rotational losses are 1.1 KW. If the motor is operating at 87 % efficiency, find the converted power and the copper losses. Select one: O a. Peony =16 02 KW and Pa = 1.13 KW Ob. P.ry= 14.92 KW and P = 1.35 KW Oc None Od. Por= 1715 KW 3nd Pa-211kw Consider a shunt DC motor with an armature resistance RA -0.125 2 and terminal voltage VT =460V. TIhe motor rated speed is 1000RPM and the rated amature current is 100 A. The total field resistance is 260 Ohms
The induced emf in a dc machine when running at 500 rpm is 180 v. calculate he induced emf while the machine is running at 600 rpm by assuming flux to be constant
f the angular speed of a rotating machine is 188.5 rad/sec, The speed in rpm is ........... a. 1000 b. 900 c. 1800 d. 1250
A 230 V dc series motor has Ra=0.22, Rf=0.12. The motor draw 40A at rated speed and 1000 RPM. Find the speed of the motor if it draw 20A at rated voltage. Assume that the flux at 20A current is 60% of the flux at 40A.
Q9 / What are the function of brushes , pole and commutator in DC machine
The torque developed by a dc series motor is 10 N-m when drawing 7 A. If the current is doubled, the tor developed becomes N-m. of estion
6. Home Works: a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 N jo.22 Q j0.22 0 0.05 0 j6.28 NE E1 V
The induced voltage in dc motors beyond the pole edges is Select one: O a infinity b. 180 V C. 220 V O d. zero
6. Home Works: a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 0 jo.22 Q j0.22 0 j6.28 NE E1 0.05 0
A 220V DC motor rotating at 1500 rpm (revolution per minute = devir/dakika (d/d)) draws 10A. The torque transferred to the load is 13Nm. What is the output power and efficiency of the motor? (Note: P=2πTf [P=power, T=torque, f=frequency].)
The frequency of voltage generated in SG depends on: Select one:a. Number of polesb. number of poles and speed rotationc. Field currentd. Rotor speede.Number of poles, speed rotation and type of winding