3. A doubly reinforced beam has dimension of 300mmw x 600mmh. It is reinforced with 2-25mm diam compression bars and 4 25mm diam tension bars. Concrete cover from centroid of steel bar is 60mm. On its section has a bending moment of 300KN-m. Using working stress design method what are the stresses acting on the concrete, compressive and tensile steel bars? n=8

3. A doubly reinforced beam has dimension of 300mmw x 600mmh. It is reinforced with 2-25mm diam compression bars and 4 25mm diam tension bars. Concrete cover from centroid of steel bar is 60mm. On its section has a bending moment of 300KN-m. Using working stress design method what are the stresses acting on the concrete, compressive and tensile steel bars? n=8

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

concrete floor slab 100 mm thick is cast monolithic with concrete beam 2.0 m on centers. The beams have a span of 4.2 m and have a web width of 250 mm, and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry; a) effective flange width of an interior beam in mm b) depth of uniform stress block at ultimate stage in mm ( round of to nearest whole number) c) tensile steel strain compatible with concrete strain if 0.003 ( round if 3 decimal places)
A simply supported beam is reinforced with 5-25mm at the bottom And 2-20mm at the top if the beam. Concrete covering to centroid of reinforcement is 70mm at the top and 64 mm at the bottom. The beam has a gross depth of 450 mm and gross width of 300 mm. Fc’=28 mpa fy= 415 mpa. Assume bars are laid out in a single layer. calculate the following if the limiting tensile steel strain is 0.004 for ductile failure: a) depth if neutral axis from the extreme concrete compression fiber ( in mm, in whole number) b) design strength of the beam section ( in kn•m , in whole number) c) maximum service uniform live load over the entire span in Addition to a DL = 20 kn/m ( including weight of the beam) if it has a span of 6 m ( in kn, in whole number)
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameters bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 Mpa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm Depth of uniform stress block at ultimate stage in mm to the nearest whole number Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f'c = 25MPa 800 730 N12 ligs (fx.t-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Use the Transformed section approach considering the presence of steel. Calculate the concrete area and transformed steel area in both tension and compression shown in Figure 3. n=Es/Ec Ast=1232mm^2 Use n-1 for the transformed area to do the calculate. Unit: mm^2 with two decimal
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
A concrete floor slab 10e mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-020 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 8.003 in 3 decimal places =
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. A. Determine maximum nominal moment to ensure tension controlled, kN-m. B. Calculate the balanced steel area, mm2. C. Calculate the balanced moment in kN-m.
The rectangular doubly reinforcement stress concrete block with the arrangement of reinforcement of 2N28 bars on top and 3N28 bars on bottom. The modulus of elasticity are Ec =23,500MPa and Es = 200,000MPa. Dead load is 18KN/m and live load is 12KN/m. f' = 25MPa 800 IDE 730 N12 ligs (fsv.f-500MPa) Ast = 3N28 350 Span = 10m Figure 3 Calculate the combination load for the reinforcement concrete beam shown in Figure 3. Unit: KN/m with two decimal. 1.2G+1.5Q=w
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000 L17 in. 20 in. 3 #9 bars (A, - 3.00 in.) 3 in. -12 in.- Select one: a. 2525 psi b. 2412 psi C. 2615 psi d. 2817 psi
Seatwork The beam shown is prestressed by using a bonded (stress relieved tendons) with a specified tensile strength of prestressing tendons strength fpu=1350 MPa, fc'=35 MPa. The area of prestressed reinforcement in tension zone Aps=1000 mm?. The specific yield strength of prestressing tendons sd, foy=1160 MPa. а. What is the value of the stress in prestressed reinforcement at nominal strength (Aps) b. What is the value of the depth of the compression block. С. What is the ultimate moment capacity of the prestressed beam. 0.85fc' 430 NA |(d-a/2) · A=1000 T=Ap.Sps 250
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =