3. A pump discharges 126 liters per second of brine (sp.gr.1.20). The pump inlet, 304.8 mm diameter, is at the same level as the outlet, 203.2 mm in diameter. At the inlet, the vacuum is 152.4 mm Hg. The center of the pressure gauge connected to the pump discharge flange is 122 cm. The gauge reads 138 KPag. For a pump efficiency of 83%, what is the power output of the motor? (2) 122 cm. PUMP

3. A pump discharges 126 liters per second of brine (sp.gr.1.20). The pump inlet, 304.8 mm diameter, is at the same level as the outlet, 203.2 mm in diameter. At the inlet, the vacuum is 152.4 mm Hg. The center of the pressure gauge connected to the pump discharge flange is 122 cm. The gauge reads 138 KPag. For a pump efficiency of 83%, what is the power output of the motor? (2) 122 cm. PUMP

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level of oil in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48 kPa absolute and its specific gravity is 0.82 Determine the NPSH in meters available. choices: a. 19.36 b. 17.23 c. 4.64
1. A pressure gauge attached to a pipe is reading 1.34 m of Hg at a place where the atmospheric pressure is 10.33 m of water. The approximate absolute pressure at the mountain isa. 930 kPab. 181 kPac. 280 kPad. 100 kPa 2. The flow is said to be unsteady and non-uniform when,a. The flow velocity is not changing with time but changing with spaceb. The flow velocity is changing with both time and spacec. The flow velocity is changing with time but not changing with spaced. The flow velocity is not changing with both time and space 3. The below figure shows a pipe with a circular cross section of diameter D mm on the left end and a square cross section with side D mm on the right end. Mercury enters the left end with a velocity 1 cm/s and leaves the right end with a velocity V2. Find V2 (neglect losses in the pipe).a. Cannot be find since length is not givenb. Cannot be find since diameter is not givenc. 7.85 mm/sd. 12.73 mm/s 4. 1 kg water is flowing through an inclined pipe at…
(Q26) A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to measure the flow of water. The pressure at inlet is 20 N/cm2 and the vacuum pressure at the throat is 27 cm of mercury. Find the rate of flow. The value of cd may be taken as 0.9
A pump delivers 20 cfm of water having a density of 62 lbs. per cubic foot. The suction anddischarge gage reads 5 inches Hg vacuum and 30 psi respectively. The discharge gage is 5 ft abovethe suction gage. If pump efficiency is 70%, what is the motor power?
Inlet and throat diameters of a horizontal venturimeter are 280 mm and 100 mm respectively. The liquid flowing through the venturimeter is water. Pressure intensity at inlet is 15 N/cm2, while pressure at throat is 50 kPa. Find flow rate of water in lit/min, assuming Cd is 0.7 and also draw the neat sketch. i) Actual flow rate = _______________________ lit/min.
pls ans asap Water flows at 0.07 cubic meter per second through a pipe. A horizontal venturi meter with throat diameter of 150-mm was used to measure the velocity inside the pipe. Based on manometer reading, the differential gauge is deflected 1.2 meter. If the specific gravity of the manometer fluid is 1.60, the diameter of the pipe, in millimeter (mm), that was used is
Q.1. A large tank contains air, gasoline (pc= 680 kg/m³), light oil (p= 800 kg/m³) and water. The pressure p of the air is 150 kPa gauge. If we neglect friction, what is the mass flow rate of oil from a 20- mm-diameter jet? 1₁-2m Air Gasoline 8G Water- 90 Oil.. d. 20 mm #i 2-3m
Fundamental of fluid flow: A venturi meter with a throat diameter of 6 cm is fitted in a horizontal pipeline of 12 cm diameter with oil of specific gravity 0.88 flowing from left to the right. The difference in level in the two limbs of a mercury manometer connected to the tapping points read 12 cm and the connecting pipes are filled with the same oil. (a) If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. Determine the difference between the 2 gage pressure readings in kPa. (b) Determine the flow in m^3/s neglecting head losses.
3. A Prandtl tube (Pitot-static tube with C=1) is used to measure the velocity of water. The differential manometer reading is 10 mm of liquid column with a relative density of 10. Assuming g = 9.8 m/s?, the velocity of water (in m/s) is
Include a free body diagram A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74 m B. -4.67 m C. 2.56 D. -2.72 m
Toplam basınç göstergesi Manometre Vana Venturimetre Debiölçer Hazne Pompa Manometre=Manometer Venturimetre=Venturimeter Debiölser-Flaw meter Vana=Valve Pompa=Pump Hazne=Tank Toplam Basınç Göstergesi =Total Pressure Gauge It is desired to display the flow in the venturimeter, How can you determine this? Explain bY. explaining the method vou bave chosen.
The longest pipe run for a hot water system is 100 m. If the pressure rise through the pump is 35 kPa, then the pressure drop per one meter in system is إختر أحد الخيارات: Pa/m 233.3 .a O Pa/m 400 .bO Pa/m 250 .c O Pa/m 375 .d O