3. Determine the allowable end bearing resistance of a 16" x 16" square pile bearing in a clay material 40 feet below the surface. The clay has a unit weight of 115 pcf and undrained shear strength of 2500 psf. Assume a factor of safety of 3.0 is required.

3. Determine the allowable end bearing resistance of a 16" x 16" square pile bearing in a clay material 40 feet below the surface. The clay has a unit weight of 115 pcf and undrained shear strength of 2500 psf. Assume a factor of safety of 3.0 is required.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.37P

See similar textbooks

Related questions

Q: Q1: Determine the required fire flow for a three storeys wood frame building covering 700 m2 which

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Describe the Standard Model of Consolidation

A: The Standard Model of Consolidation is a geotechnical engineering model that was developed to…

Q: Given: Draw ㅑ the 2 Kip/FE 5 Ft A shear + and 5 Ft moment 30 kip-ft 5 ft diagram. B

Q: A vertical circular gate is submerged in a liquid so that its top edge is flushed with the liquid…

A: Given data:

Q: A -2 m- 30 KD 2 m 15 kN -2 m B

A: Given data:

Q: Find the reactions of the given beam using: Moment Distrbution

A: Given Data Find support reaction using Moment Distribution Method.

Q: Problem 015 Forces F, P, and T are concurrent and acting in the direction as shown in Fig. P-015. F

A: Given : To Find :

Q: 3 kN 4 m 5 kN, A L 5 kN B K 6 kN 4 kN D 4 kN E H C 2m 2 m 2 m 2 m 2 m 2 m Determine the force in…

Q: Question 2. A 500-mm diameter, 15-m deep drilled shaft foundation is to be constructed in the soil…

Q: The rigid block has a weight of 400 kN and is to be supported by posts A and B, which are made of…

A: Given, Weight of the block = 400 KN The length of each block is the same Cross sectional area =5000…

Q: A load of 6kN is supported as shown in the figure. The weight of the pulley is 2kN. Neglect the…

Q: The long cylinder is rotating counterclockwise with a constant angular velocity of 80 rad/s. The…

A: Given: w=60 rad/secR=0.3 mv∞=20 m/sPα=98 kzpaρa=1.2 kg/m3 To find: a) Stagnant points b) PA

Q: A A 1m܂ 4 kN/m 4m B 2 kN 1m 2 m 2 kN ܘܢ 1 1m C 6 kN/m 3 m D

Q: Use the Moment area theorems and determine the slope at B and displacement at B. El is constant. A…

A: Given Data EI = Constant Find slope and displacement at point B using Moment area method.

Q: What would be the change in effective stress at point A if the water table rises to ground level?…

Q: L The acceleration of at 30 m/s On a boat produces an 10 m/s². If the boat is travelling motor is…

Q: 600 N Additional problem C: (Answer: A, 3.48 kN, Ay = 816 N, FBC = 4.36 kN) The overhanging beam is…

A: Given : Determine the horizontal and vertical component of reaction at A and B ?

Q: 1.23. A- Determine the pressure head, elevation head, and total head at A, B, and C for the…

Q: Question 1. The free mean speed on a roadway is found to be 80 kmph. Under stopped condition, the…

A: Given- Free mean speed Vf=80 kmph, Spacing s=6.9 m,

Q: In a theoretical flow net, the seepage velocities along any two adjacent flow lines are always the…

A: Properties of Flow net. Each flow line and equipotential line must connect at an angle of 90 degree…

Q: a) A CU triaxial test was carried out on a silty sand soil sample. The cell pressure was equal to…

A: Given: σ3=200 kPa∆σ=410 kPau=73 kPa To find: 1) The cohesion intercept is zero. 2) The friction…

Q: Determine the shear and moment in function of x, and then plot the shear diagram and the moment…

Q: ow. What is the height of the influence line at A?

Q: In an as-built survey, the XY coordinates in meters of three points on the centerline of a highway…

Q: A grit chamber of rectangular cross-section is to be designed to remove particles with diameter of…

Q: Question 57 If pressure head of water is 100m and specific gravity of kerosene is 0.81, what is the…

A: Given- Water pressure head Hw=100 m SG of kerosene=0.81

Q: Determine the center of mass for the laminae given in figure. (0,3) (0,0) (1,2) (1,0) (2,3)

Q: Show

Q: 1. Solve the support reactions at B and C using Three-Moment Equation. A 2m B 2 kN/m 3m

A: Data given Find : support reactions using Three moment equations

Q: PROBLEM 1 What is the stress of a single wire used to replace the wires with tension forces T1, T2,…

Q: Q-7, A constant-head permeability test was conducted on a soil specimen under a hydraulic gradient…

A: Given data- A constant-head permeability test- Hydraulic gradient i = 2.5, Specific gravity G=2.65,…

Q: The cross section of a rectangular gate AB of width 2 m is shown in Figure 2. The weight of the gate…

A: For such type questions use pressure diagram for simplicity

Q: The length of a simple curve having a degree of curve of 5° is equal to 130 m. If the stationing of…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: What is the fiction angle of slice 3 in the figure bleow ? a. 25o b. 26o c. 27o

A: Given data:

Q: Given the data below about the Axial Strain (%) vs Deviator Stress: Axial Strain (%), X Deviator…

A: Axial strain vs deviator stress curve data set is given. Lagrange interpolation is used to get any…

Q: Q3. Using the equilibrium method, draw the influence lines for the vertical reactions at supports A…

A: Question is simple if we use Muller breslaus principle but question is asked to solve by equilibrium…

Q: Given the Bank of Level A of arbitrary elevation 18.52 m, it is required to determine the elevation…

A: Answer We know that Height of Instrument is given by HI = Elevation of known point + Backsight to…

Q: Traffic flow on a single lane road is moving with a free flow speed of 40 kph and density of 50 vpk.…

A: Given data: Free flow speed (v)=40 kph Density (k)=50 vpk Flow is stooped for (t)=45 sec jam density…

Q: A researcher was positioned at the side of a 2-lane rural highway. He recorded the volume of…

A: Given data:- The recorded volume were 243, 276, 318 and 490. Use formula:- PHF=V60490×Vnn ----(1)

Q: What is the airport reference temperature, if the monthly mean of average daily temperature for the…

A: Given ta=24oC, tm=30oC,

Q: Data on density and speed were obtained from a four-lane, two-way rural highway (alogn one direction…

Q: The beam seciton shown below has moment of inertia about its neutral axis: I = 301.3 (10 -6)m 4 ,…

A: Figure is given in the question

Q: 1. A simply-supported beam illustrated in Figure 5.1 is subjected to a uniformly distribut load w.…

Q: Problem-soil. A concentrated load of 2000kN is applied at the ground surface. What is the vertical…

A: Given data: A concentrated load, Q = 2000 kN The point directly below the load, z = 6 m

Q: Estimate

Q: A concrete dam is going to be built on a silty/clayey sand stratum as shown in Figure 1 to provide a…

A: Given- Length of dam L=100 m, Unit weights- γw=9.81 kN/m3,γsat=18.5 kN/m3, Number of potential…

Q: 2. Calculate the moment of inertia of the shaded area about the x-axis as shown. 80 mm 80 mm 60 mm

Q: According to the general shear stress formua, shear stress distribution on a rectangular crosss…

A: This question is related to the Solid Mechanics from Civil Engineering. Given Data - Crosss…

Q: Problem Steel and aluminum plates are used to reinforced an 80 mm by 150 mm timber beam. The three…

A: Given : Timber beam section = 80 mm X 150 mm To Find : Find the safe resisting moment of the beam…

Concept explainers

Pricing Excavation and Backfill

Backfill, in construction, is the activity of returning the soil and gravel that are removed during building construction or using them again to toughen and support the foundation of the building or any other structural component.

Question

3. Determine the allowable end bearing resistance of a 16" x 16" square pile bearing in a clay material 40 feet
below the surface. The clay has a unit weight of 115 pcf and undrained shear strength of 2500 psf. Assume
a factor of safety of 3.0 is required.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Concept

VIEW

Step 2 Solution

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Based on Meyerhof’s (1956) suggestion, do you think a mechanical or electrical cone penetration resistance (??) can be used to be the pile point ultimate bearing capacity (??)? C. Yes D. No
What is the pile bearing capacity if the Downward drag = 0.6 psi, h1 = 30', h2 = 4', Frictional stress = 3.5psiAxial stress = 250psi.
The diamter of precast round piles under pile cap is 400mm, the embedded depth of cap bottom is 1.5m, the thickness of the soft clay 1₁=8m and enter the hard plastic clay /₂=2m. Try to calculate the bearing capacity characteristic value of a single pile according to building foundation design code. Asia 5kPa soft clay hard Asia 35kPa Apa 1025kPa clay 8m 2m 1.5m
A cantilever wall is to be installed in a granular material which has a unit weight of 122 pcf, a friction angle of 35 degrees. The height of the wall (H) is 29 ft and the ratio between the top of the wall the water to the wall height (a) is 0.25. The ratio of the pile soil friction angle to the soil friction angle (8/q) is -0.7. Using the Caquot and Kerisel lateral earth pressure coefficients and the chart solution in the "Steel Piling Design Manual" (USS, July 1984), what is the required sheetpile section in in^3? Use USS Mariner steel.
Stresses Due to Combined Loads: The 300-mm-diameter concrete pile is pushed into the soil by the 600-kNforce while being rotated about its axis by the torque T. Find the largest allowable value of T (kN-m) for which the tensile stress in the pile does not exceed 1.8 MPa.
Answer the following 1-Point bearing piles extend to a stable soil or rock layer below the superstructure. [T\F] 2- In loose sand, the unit skin friction is lower for a high-displacement pile, when compared to a low-displacement pile (at similar depths). [T\F] 3-Typically we place shallow foundations underground. [T\F] 4- If the spread footing covers more than 50% of the building footprint, a mat or deep foundation is more economical. [T\F]
Q2/What are the Classification of Piles According to Method of Construction?
Estimate ultimate capacity of a timber pile with tip diameter of 180 mm and top diameter of 360 mm, driven to 12 m depth in the following soil profile: 0-3m sand: medium dense 3-7m clay: clay: with unconfined compressive strength 100 kPa compressive strength 200 kPa 7-11m 11-15m gravel: N6o=30 Water Table at 3m depth Assume soil unit weight 19 KN/m³
A concrete pile 458 mm by 458 mm square cross section is embedded in a saturated clay. The length ofthe embedment is 16 m. The undrained cohesion, Cu of clay is 60 kN/m2, and the unit weight of clay is 19 kN/m2• Use a factor of safety of 4 to determine the allowable load the pile can carry.
1. A ten-story building is to be constructed at a site where the water table is close to the ground surface. The foundation of the building will be supported on 0.5 m diameter and of length 25 m concrete piles. The bottom of the pile cap will be at the ground level. The soil investigation at the site and laboratory tests have provided the saturated unit weights, the shear strength values under undrained conditions, and the soil profile of the soil. The soil profile and the other details are given in Table below. Required: a. Draw the soil-pile system. b. Determine the ultimate bearing capacity of a single pile. From 0 6.0 22 30 Depth To 6 22 30 40 Soil Sand Med. stiff clay Sand Stiff clay Y sat kN/m³ 19 18 19.6 18.5 0° 33 30 Cu kN/m² - 60 75
(i) What are the components of elastic settlement of piles? Name two parameters that affect the settlement. A 300 mm diameter pile penetrates a deep deposit of soft clay 9 m deep. Compute the skin friction and point bearing capacity. The clay has an undrained unit cohesion of 60 kN/m?. Assume a (ii) constant friction coefficient of 0.75 and use a method.
What is the design capacity of a square pile 0.3 x 0.3 m if it has a skin fiction of 660 KN. Assume cohesion of soil is 90 KPa and the bearing capacity factor Nc = 9. Use factor of safety of 2.