3. Determine the daily load and the peak power required (with the help of daily load curve time schedule diagram) by a PV system that has three appliances connected to it with the following characteristics: 1. LED Lamp, 20 W operated for 3 h (10 am to 1 pm). 2. CFL Lamp, 10 W operated for 8 h (9 am to 5 pm). 3. DC Fan, 30 W operated for 2 h (2 pm to 4 pm)

3. Determine the daily load and the peak power required (with the help of daily load curve time schedule diagram) by a PV system that has three appliances connected to it with the following characteristics: 1. LED Lamp, 20 W operated for 3 h (10 am to 1 pm). 2. CFL Lamp, 10 W operated for 8 h (9 am to 5 pm). 3. DC Fan, 30 W operated for 2 h (2 pm to 4 pm)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

An alternating voltage, given by v = 100 sin 314t is connected to a full-wave rectifier. The average value will be _________. 31.8 volts 63.7 volts 70.7 volts 50 volts A sinusoidal current has a rms value of 3 amperes, its maximum value will be ______. 3.46 amp 2.1213 amp 0.866 amp 4.2426 amp A sine wave has a maximum value of 20 volts; its value at 135° is _________. 15V 5V 10V 14.14V
9. When making a high energy measurement: a. Attach the meter to the energized line first, then to ground. b. Attach the meter to ground first, then to the energized line. c. Attach both meter leads concurrently. d. Remove power completely, attach the meter, then restore power.
Could you slove this dc electrical circuit
Two 115-V incandescent lamps A & B are connected in series across 230-V dc source. Lamp A is rated 100 W and lamp B is rated 60 W. Which lamp is abnormally bright and hence will burn out soon? a) Lamp A b) Lamp B c) Both lamps will be abnormally bright d) Both lamps will work normally O a. Lamp A O b. Lamp B O c. Both lamps will be abnormally bright O d. Both lamps will work normally
i. Draw the block diagram of a solar Photo-Voltaic system with the stand by diesel generator and explain about each component in it? ii. Discuss how you can you avoid the overcharging of the battery?
Discuss the operating principle of the hydroelectric power plant
Answer the question briefly. 1. What is Alternating Current (AC)? Draw a simple graphical representation of AC. 2. What are the advantages of using alternating current over direct current?
List out all the major components in a thermal power plant
refer to the circuit below, a. what is the secondary voltage of the circuit (answer in Vrms) b. what is the DC current and rectified DC voltage across the load? c. what is the maximum current in the circuit? d. what is the direction of the DC current through the load?
An alternating current was measured by a DC milliammeter in conjunction with afull-wave rectifier. The reading on the milliammeter was 7.0 mA. Assuming thewaveform of the alternating current to be sinusoidal, calculate: (a) the r.m.s. valueand (b) the maximum value for the alternating current.
What are the range of voltages can the Logo SIEMENS work within? Which model DC and which one AC supply?
Make three plots using Excel: 1. Voltage vs current for the linear resistor data (voltage on vertical axis, current on horizontal). Add a linear trendline with the equation and R² value shown. 2. Voltage vs current for the lightbulb data (voltage on vertical axis, current on horizontal). 3. A plot showing both curves on the same set of axes (voltage on vertical axis, current on horizontal).