3. In Amplitude modulation, Vestigal Side Band (VSB) is one of the technique used to overcome its limitations in terms of power and bandwidth. With this in mind; a. Explain how a VSB signal is generated in the transmitter. b. Draw and compare the frequency spectrum of the original message signal and the spectrum of the VSB signal in a frequency domain. c. Show how the bandwidth of VSB is calculated by writing the equation. d. Give one application of VSB in broadcasting.

3. In Amplitude modulation, Vestigal Side Band (VSB) is one of the technique used to overcome its limitations in terms of power and bandwidth. With this in mind; a. Explain how a VSB signal is generated in the transmitter. b. Draw and compare the frequency spectrum of the original message signal and the spectrum of the VSB signal in a frequency domain. c. Show how the bandwidth of VSB is calculated by writing the equation. d. Give one application of VSB in broadcasting.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. Write down the general expressions of frequency modulated signal and phase modulated signal. And show the methods to generate FM signals.
4. Given FM modulator with the following parameters: Frequency deviation = 44 kHz Modulating signal, vm = 2 sin (2rókt) a) Determine the modulation index. b) Determine number of sets of significant side frequencies. c) Determine the bandwidth using both Bessel function and Carson's Rule. d) Sketch the output frequency spectrum for the Bessel approximation.
Question 4. Select the statement that best describes the PM wave.a. Carrier phase angle changes represent the PM modulated signal, however, unlike FM and AM modulatedcarriers, it is not always easy to see these phase changes in the plot.b. The FM signal accurately represents the message.c. Although PM and FM techniques are classified as angular modulation techniques, they cannot be usedinterchangeably (i.e., modulated with FM and demodulated with PM, and visa versa).d. All statements are correct.
Direct method for generation of FM signal does not give high stability to FM signal frequency O a. True O b. False
Q7. Figure Q7(a) shows the spectrum of a frequency modulated waveform with a sinusoidal modulation. 12 4.8 5.0 5.2 5.4 5.6 5.8 6.0 Frequency/MHz Figure Q7: (a) Spectrum of a frequency modulated waveform with a sinusoidal modulation. (a) Is this modulated waveform described as narrowband or as wideband? (b) What is the value of the carrier frequency? (c) What is the value of the modulation frequency? (d) Determine the value of the peak frequency deviation. Plots of Bessel functions of the first kind are provided below in Figure Q7(b) to assist you. (e) Estimate the fraction of the total signal power at the carrier frequency. (f) Detection of such a frequency modulated signal is usually accomplished with the use of a discriminator. Describe the function of a discriminator. (g) What is the equivalent AM modulation index obtained if this signal in Figure Q7(a) is demodulated with a high-pass RC filter discriminator? J„(x) 1.0 0.8 0.6 0.4 0.2 -0.2 -0.4 Figure Q7: (b) Bessel functions of the…
A 1500 KHz carrier with amplitude of 50 V is amplitude modulated by 2 –KHz sine wave tone with a peak voltage of 15 V. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
2 (AM) A 10 V amplitude sinusoidal signal is used as a modulating signal to generate an AM signal with modulation index 0.8. What is the amplitude of the carrier? What is the power of the side bands? What is the efficiency of the modulated signal?
S Answer the two following questions: A. A sinusoidally modulated AM waveform is shown below: Determine: (a) Peak amplitude of the upper and lower side frequencies. (b) Peak amplitude of the unmodulated carrier. (c) The modulation index. (d) The transmission efficiency. (e) The amplitude of the carrier which must be added or subtracted to attain a modulation index of 0.5. 16V 8V- -8V. -16V-
The phenomenon of a strong FM signal dominating a weaker signal on a common frequency is reffered to as the a. Calcify effect b. Caption effect c. Capture effect d. Capstone effect
Q6. Figure Q6 shows the line spectrum of a modulated signal (all components are positive and real). 3 1 232 234 236 238 frequency/kHz Figure Q6: Line spectrum of a modulated signal (a) Describe the modulation scheme. (b) What are the values of the carrier frequency, modulation frequency and the modulation index? (c) What is the transmission efficiency (ratio of modulated to total power) in this example? (d) The reception of this signal is undertaken with a superheterodyne detector using an intermediate frequency of 110 kHz. What is the appropriate local oscillator frequency? (e) Demodulation of this type of signal is usually accomplished using an envelope detector. Describe the principles of operation of an envelope detector and sketch an example circuit. (f) What considerations should be made about the component values in the design of an envelope detector in order to demodulate the signal after shifting to the intermediate frequency? Relative unitsS
A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform is shown below. 3.5V- 1V- a) What is the amplitude of the carrier signal? b) c) To achieve 75 percent modulation, what amplitude of the modulating signal is needed? d) Calculate the effective voltage of the AM signal What is the modulation index?
Q2. For the scheme shown in Figure Q2, i. Draw the spectrum of the baseband signal (multiplexer output) for the multiplexer. ii. Determine the bandwidth of the baseband signal (multiplexer output) for the multiplexer. i. Determine the minimum transmission bandwidth of the multiplexer. Explain, briefly, the modification needed for the multiplexer in the figure to achieve this bandwidth. 4 kHz cos 10,000xt Basebund signal cos 24,000mt cos 2000mt cos 32,000nt Figure Q2