3. The extremities of any diameter on Mohr's circle represent: a) principal stresses. d) none of the above. 4. A body is subjected to a two normal stresses 20MPA (tensile) and 10MPa (compressiv perpendicular to each other. The maximum shear stress is: b) normal stress on plane at 45°. c) shear stress on plane 45°. a) 5MPA. b) 10MPA. с) 30МPа. d) 15МPа.

3. The extremities of any diameter on Mohr's circle represent: a) principal stresses. d) none of the above. 4. A body is subjected to a two normal stresses 20MPA (tensile) and 10MPa (compressiv perpendicular to each other. The maximum shear stress is: b) normal stress on plane at 45°. c) shear stress on plane 45°. a) 5MPA. b) 10MPA. с) 30МPа. d) 15МPа.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A 10 mm thick steel tank has an outside diameter of 500 mm and a length of 4m. It is subjected to an internal pressure of 10000 kPa. a) Determine the circumferential stress in the tank. b) Find the longitudinal stress in the tank. c) To what value could the internal pressure be increased if the allowable design stress is 110 MPa?
a) b) Question 2: Draw the bending moment diagram identifying the location and value of maximum bending moment. Find maximum tensile and compressive stresses and draw the stress diagram. 150mm 500mm Cross-section 1m 20KN Figure Q2 10kN/m 3m 20KN +- 1m
The reference state of stress shown in the element sketch below results in the Mohr’s circle plot indicated. For this element, as described below, determine:a)The principal stresses.b)The principal directions (angles to the principal planes).c)The maximum in-plane shear stress.d)Is the maximum in-plane shear stress the absolute maximum shear stress?
3- A loaded structure with a two-dimensional stress state has the stress in the x-axis is 13.5 Mpa, in the y-axis is - 3.2 Mpa, and the shear stress in the x-y is - 4.4 Mpa. a) Write the stress transformation equations b) Calculate o and t for the inclination angle 0 between the n values 0 to 180°, in 15° increments. c) Draw the profile graph of normal stress and shear stress with e in the x-axis d) Obtain from the graph, the principal stresses o,, o,, and 2' maximum and minimum shear stresses Tmax and tmin e) Obtain from the graph the corresponding inclination angle Op1, Op2, Os1, and es2 for each of principal stresses and shear stresses, respectively
a) If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the maximum allowable stress in the pipe is 7.5 x 109 N/m2 , calculate the minimum wall thickness required for the pipe. Give your answer in millimetres (mm) to 2 decimal places. b)A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2 to 2 decimal places.
A 115 m long steel cable with a cross-sectional area of 1.13 x 104 m? is subjected to a tensile force of 565 N. Find the following: a) the stress b) the strain c) the change in length of the cable
When an object is placed underwater, the pressure on the object is subjected to uniform stress on all sides. a) define volume strain, the bulk modulus, compressibility, and the relationship between the bulk modulus and compressibility. b) A 100 litre volume of liquid is subjected to a 2000 psi increase. If the compressibility of the liquid is 5 x 10-5 per atm, find the bulk strain and absolute decrease in the volume of the liquid c) explain the concepts of shear stress and shear strain? could these concepts be applied to the fluid problem above?
Question 3 For the figure shown below, compute the normal force in section 1. Neglect the weights of the member. Note that point B is pin- connected. 50KN B ... 2m, 5m AG 5m 5m 13.66 kN B) 43.66 kN 23.66 kN D) 33.66 kN E) 3.66 kN F 6.66 kN G. 18.66 kN 2.66 kN
For the state of stress given, determine: A) The principal stresses and the maximum shear stress. B) The orientation of the element of the principal stresses and the orientation of the element of maximum shear with corresponding normal stresses. C) Draw Mohr's circle
In the case of plane stress given in Figure 1 a) normal and shear in the shaded plane Find their stresses b) principal stresses c) principal directions. d.) Results obtained Show on Mohr Circle and oriented element
A 3.00 m long, 8.0 kg pole is attached to a wall by a hinge on its left side. A cable attached to the right end of the pole holds it horizontal. The cable attaches at a 55.0° angle. A 10.0 kg box hangs from the pole at a point 1.25 m from the right end of the pole. (see diagram) hinge. 55° 1,25m a) Write out the sum of the forces and sum of the torques equations. b) What will be the Tension on the cable? 10k₂ c) What will be the magnitude and direction of the force on the hinge?
The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast iron. Calculate the followings: a.) b.) 3 kN Normal stress at point H. Shear stress at point H. Normal stress at point K Shear stress at point K. d.) 5 kN 450 mm 150 mm 150 mm 2 kN 200 mm 5 kN