3. The following characteristics are specified for a particular Zener diode: V₂ = 29 V, VR = 16.8 V, Izt = 10 mA, Ir = 20 mA, and Izm = 40 mA. Sketch the characteristic curve in the manner displayed in Fig. 1.47. H 0.7 V 10μA-V₂ -0.25A- 125 mA FIG. 1.47 Zener diode characteristics with the equivalent model for each region

3. The following characteristics are specified for a particular Zener diode: V₂ = 29 V, VR = 16.8 V, Izt = 10 mA, Ir = 20 mA, and Izm = 40 mA. Sketch the characteristic curve in the manner displayed in Fig. 1.47. H 0.7 V 10μA-V₂ -0.25A- 125 mA FIG. 1.47 Zener diode characteristics with the equivalent model for each region

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
uO 9:.0 A docs.google.com * ZAIN IQ l. Q3/B: Assume an ideal diode model for all the diodes in the circuit below. calculate voltages and currents through D1 and D2 9kQ 1N1199C R2 D1 18KQ 1N1199C D3 1N1199C V2 =12 V R3 1kQ R4 5kQ 1.22 V 11 mA 0.5 A O VD1 ID1 VD2 ID2 صفحة 4 من 6
Given the following circuit with VDD = 9.5 V, R = 3.2 k2, then the current Iis: Use the CVD model for the diode, with VD = 0.65 V. VDD I a. 0 A O b. 0.002766 A c. 0.002969 A d. 2.968750 A e. 2.765625 A R N V₂
A semiconductor diode having ideal forward and reverse characteristics is used in a half-wave recti- fier circuit supplying a resistive load of 1000 Q. If the r.m.s. value of the sinusoidal supply voltage is 250 V, determine (i) the r.m.s. diode current * 170mA O 171 mA O 172mA None of the above
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
A diode whose internal resistance is 20 ohms is to supply power to a 1000-ohm load from a 110V(rms) source of supply. determine the percent regulation from no load to the given load. A 1.81 % B 2.06 % C 3.19 % D 5.45 %
Consider all Si diodes Find Vi and Vo relationship assuming diode ON and OFF Draw the timing diagram between Vi and Vo Draw the transfer characteristics
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms
Question 1: In the circuit shown below, the output (Vo = 10V Max.) Unipolar. The frequency of Primary is 60 Hz. The diodes are Silicon with VD = 0.7V. a. Sketch the output without a Capacitor. b. Determine Voc without a Capacitor. c. Sketch Vs (at the Secondary). d. Determine Voc with a Capacitor of 10 uF across RL. e. Determine the RMS Value of Vp (at the Primary). f. PIV (Peak Inverse Voltage). 10:1 Output C. 22 k1 All diodes are IN4001. | 00000
Assuming an ideal diode model for all the diodes in the circuit below, Calculate the voltage across and current flow through each diode R1 D2 9kQ 1N1199C R2 D1 18k0 1N1199C V2 12 V R3 1kQ D3 1N1199C R4 5k0