3. Two identical 600 kW, 230 V dc generators are operating in parallel and take equal shares of an 800 kW, 250 V busload. The voltage regulation of each machine is 5%. If one of the generators is accidentally tripped off from the line, what is the voltage of the remaining machine?

3. Two identical 600 kW, 230 V dc generators are operating in parallel and take equal shares of an 800 kW, 250 V busload. The voltage regulation of each machine is 5%. If one of the generators is accidentally tripped off from the line, what is the voltage of the remaining machine?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 10. Determine the shunt resistance needed to convert a galvanometer to an ammeter with a full scale…

A: In this question, We need to determine the shunt resistance needed to convert the galvanometer to…

Q: 4.17 The circuit shown in Fig. P4.17 is known as a noninverting integrator. For the ele- ment values…

Q: 2. superposmon a) 6V(+ 2mA OITTe 2 km www 4th 2kf Cons 6 kn ww 01

Q: - الترد وتم - Y(s) 2s+1 U(s)

Q: A magnetic circuit has a m.m.f. of 400 AT and a reluctance of 2 x 105 AT/Wb. The magnetic flux in…

Q: Q3/ Consider the circuit in Figure (2), answer (a)-What type of circuit is this? (b)-What is the…

Q: The zeros of the transfer function * s²+2s+2 s4 +6s3 +4s²+7s+12

A: Given transfer function: F(s)=s2+2s+2s4+6s3+4s2+7s+12

Q: Q.3 When a line-to-ground fault occurs, the current in faulted phase 'a' is 100A. The zero-sequence…

Q: an output voltage of 20V across a 1K0 load with an input that will vary between 30V and 50V. That…

A: The required resistance and the maximum current have been identified.

Q: H (jw) = Y(jw) 105 (10 + jw) (1000 + jw) X (jw) (1 + jw)(100 + jw)(10000 + jw) =

Q: Q2) Determine and draw the output voltage for the circuit in Figure 2.

A: It is given that:

Q: Vin C₁ HE 0.0022 μF 4 mH 4 00000- R₁ 150 22 Vout What is the bandwidth in the given circuit. If the…

Q: Two long parallel current carrying wires are separated by 5 cm in air and are carrying current of…

Q: An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 900Hz.…

Q: For a 4 pole induction motor find the synchronous speed if its running at 440V, 50 Hz A.C. supply.

A: Given, For an induction motor, Total number of poles, P = 4. Supply voltage, Vs = 440 V. Frequency,…

Q: A DSB-SC modulation generates a signal y(t) = Acm(t) cos (wet+0). (a) Sketch the amplitude and phase…

Q: Question 7: A 415V, three-phase, 50 Hz, 4-pole, star-connected induction motor runs at 24 rev/s on…

A: NOTE: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts…

Q: A loss-less transmission line having characteristics impedance Zo is terminated in a load of Z₂. If…

A: Given, A lossless transmission line having, Characteristics impedance = ZO. Terminated to load…

Q: The electron concentration in a piece of Si at 300 K is 10^5 cm^-3. What is the hole concentration?

Q: Find current i using mesh current analysis for the circuit. 4.3 V 2.2 V 6.8 ΚΩ Μ 3.3 ΚΩ Σ 9.1 ΚΩ

A: Given circuit,

Q: What factor is directly proportional to PC in ?Normal AM Amplitude of signal Signal types O carrier…

A: Modulation: Modulation is a process enhancing the strength of the signal. Modulation increases the…

Q: :One kilowatt-hour is the power consumed by a 1kW- load during one hour.a None of the answers is…

A: Kilowatt-hour: It is the standard unit of measurement of representing electrical energy. It is…

Q: A 100 kV, 50 Hz supply is fed to a rectifier ammeter (using a bridge rectifier) through a capacitor.…

A: The PMMC meter problem is solved as below

Q: What are the modes of operations used in 8253?

Q: 1. Two shunt generators A and B operate in parallel, and their load characteristics may be taken as…

Q: 7 3- 4- The directivity of the Infinitesimal dipole equal to dB. 5- The return loss (RL) equal to…

Q: We have a nonlinear resistor that is approximated by a piecewise linear model, as is shown in Fig.…

Q: N₁ = h(t) = [1-e-Ju(t) No = ? to find (t). 18 N Use the convolution theoren to find

Q: 5.5 Straight Outta Compton In class, we looked at Compton Scattering of a photon and a free…

A: Solution of question (A): It is asked to discuss the relation between the change in wavelength and…

Q: What are the advantages of switching from copper to fiber optics as a transmission medium?

A: Optical fiber cables have been the strongest transmission medium as well as a technology that…

Q: A drawing hall 30 m by 15 m with a ceiling height of 5 m is to be provided with general illumination…

A: Given,Area of the hall, A=30m×15mCeiling height, h=5 mGeneral illumination, E=120 luxUtilization…

Q: B: Drive the radiation intensity equation of an isotropic antenna.

A: ISOTROPIC ANTENNA PROPERTIS No pre- specified direction of the radiated wave It can radiate in any…

Q: In an ac circuit if the peak value of the voltage is 200 V what is the rms value?

Q: A current of 20A flows through a load having a resistance of 2 ohm. Determine the power dissipated…

A: Current I = 20 A Load resistance RL= 2 Ω Coil resistance Rc = 0.01 Ω We have to find the the value…

Q: For the closed-loop system shown, and given: 5 G(s) 20 8²+ 2.938+ 5 Pref + C(s) control G(s) plant…

Q: 4. Find the unknown currents marked in below figure. A 20 A B 50 A D 15A 13 120 A F E 15 40 A

Q: Given the following nodes from A to G as shown in the diagram, determine the shortest path network…

Q: A magnetic circuit has a m.m.f. of 400 AT and a reluctance of 2 x 105 AT/Wb. The magnetic flux in…

A: Given- m.m.f of magnetic circuit = 400 AT , Reluctance=2×105 AT/Wb , To find - Magnetic flux in…

Q: 5- The return loss (RL) equal to source. ............ when all power injected to the antenna…

A: These have been answered.

Q: A communication channel has magnitude spectrum and phase spectrum defined as: H()=1 0h() = sin 2xƒT…

A: We need draw magnitude and phase response ,

Q: Determine alpha dc if I E = 2.8 mA, I C = 2.75 mA and ICBO = 0.1 mA

Q: Assuming that a 4-bit ADC accepts analog input ranging from 0 to 6 volts, solve the following: a)…

A: ADC stands for analog to digital converter. It convert analog signal in to digital form . Digital…

Q: Find the voltages U₁ and ₂ f

A: Given data, In the given circuit there are two unknown variables V1 and V2 when two resistors R1 and…

Q: Figure 2-17. 08. +||||| 0} I T I I T ||||||| T I I 1 1 1 1 T " I T 100 1111

Q: 22. Minimize the Boolean function F(A,B,C,D) = Em(0,1,3,5,8,11)+ Edm (2,7,10,15) using K map in both…

Q: For the circuit shown, the potential of point A is zero. Determine the potential of poir 2.00 Q A…

A: Here basic properties are applied to solve it.

Q: Find the complement of the Boolean function F F(x, y, z)=x + yz Select one: O a. y'z O b. O c. x'y'…

A: Given, The Boolean function, Fx,y,z=x+yz.

Q: The formula used to fit ILED versus VLED was Y = a (1-e^-bx). Compare this equation to the shockley…

A: SOLUTION GIVEN--> Y = a(1- e-bx) Compare this…

Q: pe or basic meter is configured as a wattmeter? 6. Two 150V voltmeters are being compared; meter A…

Q: A workshop 100 m x 50 m is to be illuminated with intensity of illumination being 50 lux. Determine…

Question

Neeeded answer of it

3. Two identical 600 kW, 230 V dc generators are operating in parallel and take
equal shares of an 800 kW, 250 V busload. The voltage regulation of each
machine is 5%. If one of the generators is accidentally tripped off from the line,
what is the voltage of the remaining machine?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the voltage at the terminals of the generator and the voltage at the feeder in a dc series generator is supplying a current of 8.5 A to a load through a feeder of total resistance, 1.25 ohm. The generated voltage is 480 volts. The armature and series field resistances are 0.35 and 0.48 ohms respectively.
D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage
What are the main effects of losses on the performance of the alternator?
A dc generator is run at 500 rpm. The eddy current losses and hysteresis losses are found to be 100 and 200 W, respectively. At what speed will it be run to reduce the core losses by 20%?
When the field resistance in the synchronous generator decreased, its flux and terminal voltage: Select one: a. both not affected b. Flux increased and terminal voltage decreased c. Flux decreased and terminal voltage increased d. both decreased e. both increased
Mention what is the difference between generator and alternator?
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
A 35-ohm diverter resistance is shunted across the series field of a DC series generator is supplying a current of 6 A to a series lighting system through a feeder of total resistance, 1.25 ohm. The terminal voltage is 2,300 V. The armature and series field resistances are respectively 18 and 15 ohms respectively. Determine the power developed in the armature of the generator?
What is difference in alternator and generator?
The voltage induced in 8 poles lamp wound generator is 120 V with armature resistance = 0.3 2. What will be the terminal voltage at a load = 3.6 A when the machine is rewound as a wave?
The condition for maximum efficiency for a D.C. generator is variable losses = constant losses copper losses = 0 hysteresis losses = eddy current losses eddy current losses = stray losses
2- A 4-pole, wave-wound d.c. shunt generator has an armature winding consisting of 300 turns each of 0.0020. The armature resistance is a) 0.152 b)0.62 c) 0.30 d) none of above