3. Water flows through the horizontal branching pipe which is fixed by a flange as shown in the following figure. At section 1, the pipe continues to the left and hence the gauge pressure is not zero (see Figure below). At sections 2 and 3, gauge pressure is zero (atmosphere). A₂ 14 kPa A₂ 60⁰ stationary? A₂ For this problem: A₁= 600 cm² V₁=3 m/s A2= 100 cm² V₂= 3 m/s A3 = 300 m/s g= 10 m/s² p= 1000 kg/m³ What is the velocity at section 3 (V3)? What is the horizontal force F that the flange applies to keep the pipe system

3. Water flows through the horizontal branching pipe which is fixed by a flange as shown in the following figure. At section 1, the pipe continues to the left and hence the gauge pressure is not zero (see Figure below). At sections 2 and 3, gauge pressure is zero (atmosphere). A₂ 14 kPa A₂ 60⁰ stationary? A₂ For this problem: A₁= 600 cm² V₁=3 m/s A2= 100 cm² V₂= 3 m/s A3 = 300 m/s g= 10 m/s² p= 1000 kg/m³ What is the velocity at section 3 (V3)? What is the horizontal force F that the flange applies to keep the pipe system

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

13. A U-tube differential manometer connects two pressure pipes A and B. Pipe A contains carbo tetrachloride having a specific gravity 1.594 under a pressure of 11.772 N/em and pipe B contains ofl of sp. gr. 0.8 under a pressure of 11.772 N/em. The pipe A lies 2.5 m above pipe B. Find the difference of pressure measured by mercury as fluid filling U-tube. 14. A differential manometer is connected at the two points A and B as shown in Fig. 2.25. At B air pressu is 7.848 N/cm (abs.), find the absolute pressure at A. [Ans. 31.36 cm of mercuryl (Ans, 6.91 Nicm) AIR WATER OIL Sp. gr.0.8 OIL Sp. gr. 0.8 50'cm 30 cm 100 am 60 cm 10 cm MERCURY Sp. gr.13.6 WATER Fig. 2.25 Fig. 2.26
Part B: Water at 20 °C steadily flows through the reducing section at 70 kg/s. We know the following about the dimensions of the system • D1= 220 mm • D2 = 80 mm d1 P1 (1) Compute the average velocity at section 2. •{ m p2 d2
Water in the reservoir is used to control the water pressure in the pipe at A. Take pHg = 13550 kg/m³ and p = 1000 kg/m³ Neglect the diameter of the pipe. (Eigure 1) Figure AQ B E h 400 mm C 150 mm 100 mm 200 mm Mercury pe he Y Part A If h= 140 mm, determine the gage pressure in the pipe at A when the mercury is at the elevation shown. Express your answer to three significant figures and include the appropriate units. PA 76.8 Submit 4 Provide Feedback kPa CINC Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining
3. Obtain the gage pressure at the center A of the pipe shown. Ignore surface tension effects. Given: Liquid 1 S.G. = 1.5 Liquid 2 S.G. = 3.2 hi = 15 cm h2 = 30 cm h3 = 75 cm a. 589 Pa с. 452 Ра d. -452 Pa b. -589 Рa Liquid 1 Liquid 2 X1 h,
13. A U-tube differential manometer connects two pressure pipes A and B. Pipe A contains carb tetrachloride having a specific gravity 1.594 under a pressure of 11.772 N/cm2 and pipe B contains oil of sp. gr. 0.8 under a pressure of 11.772 N/em. The pipe A lies 2.5 m above pipe B. Find the difference of pressure measured by mercury as fluid filling U-tube. 14. A differential manometer is connected at the two points A and B as shown in Fig. 2.25. At B air pressu is 7.848 N/cm² (abs.), find the absolute pressure at A. [Ans. 31.36 cm of mercury] [Ans, 6.91 N/em) AIR B WATER OIL Sp. gr.0.8 OIL Sp. gr. 0.8 50'cm 30 cm om 100 cm 50 cm 10 cm MERCURY Sp. gr. 13.6 WATER Fig. 2.25 Fig. 2.26
1. Water flows through Pipe A and into parallel pipes 1,2 and 3, and out through Pipe B. The properties of the pipes are listed as follows: Pipe Length (m) Diameter (cm) 30 Friction Coefficient, f A 1 300 10 0.020 240 600 2 15 0.018 3 20 0.017 В 30 The upstream junction (near A) has an elevation of 90m with a pressure of 205 KPa; the downstream junction is at elevation 30 m. If the average velocity in Pipe A is 3.0 m/s, find the pressure at the downstream junctions and rate of flow in each pipe. Also, draw the pipe system.
%TE l, UPUOM A 9;Y) 团 / د امتحان مد1.docx The pipe assembly is subjected to the force of F = {600i + 800j – 500k} N Determine the moment of this force about point B. 0.5 m 0.4 m 0.3 m 0.3 m II
Water flows in a steel pipe (e = 0.00020 feet) at a flow Q = 12.5 cfs. The diameter of the pipe is D = 18 inches and the length of the pipe is L = 2,500 feet between section 1 and section 2. The elevation at section 1 is z = 100 feet above the datum. The elevation at section 2 is z2 = 75 feet above the datum. The temperature of the water is 70°F. The kinematic viscosity of the water is 1.06 x 10° ft/s. The pressure at section 1 is p1 = 90 psig (pounds per square inch gage). a) Determine the velocity v in feet per second (fps). b) Determine the Reynolds number Re. c) Classify the flow based on the Reynolds number Re. d) Determine the Darcy-Weisbach friction factor f. e) Determine the friction head loss hfäic in feet in the pipe between section 1 and section 2. f) Determine the pressure p2 in psiq at section 2.
Water flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.1ft 3.1ft ↓s -0.12 ft (1) 5 -0.1 ft -free jet ft³/s lb/ft²
A U-tube differential manometer connects two pressure pipes A and B. Pipe A contains carbon tetrachloride having specific gravity 1.594 under a pressure of 117.72 kPa and pipe B contains oil of sp. gr. 0.8 under a pressure of 117.72 kPa. The pipe lies 2.5 m above pipe B. Find the difference of pressure measured by mercury as fluid filling U-tube.A. 120.58. Choose the best answer below: a.31.36 cm of mercury b.25.11 cm of mercury c.64.74 cm of mercury d.13.62 cm of mercury
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
Q2: Find the diameter of the pipe 2 in the loop shown below which contains two pipes connected in parallel. Q = 10 I/s, V3= 1 m/s, A3 = 0.03 m', CHw=100, d,=150mm, L1 =1500 m, L2 =2000m. di:150 1 V-123 2. 63 21:2000m P: 2.78Td dz?? 74 7.