3.7 A reaction turbine runner diameter is 3.5 m at inlet and 2.5 m at outlet. The turbine discharge 102 m 145 m. Its inlet vane angle is 120°. Assume radial discharge at 14 m/s, breadth of wheel constant and hydraulic efficiency of 88%, calculate the power developed and speed of machine. per second of water under a head of (128 MW, 356 rpm)

3.7 A reaction turbine runner diameter is 3.5 m at inlet and 2.5 m at outlet. The turbine discharge 102 m 145 m. Its inlet vane angle is 120°. Assume radial discharge at 14 m/s, breadth of wheel constant and hydraulic efficiency of 88%, calculate the power developed and speed of machine. per second of water under a head of (128 MW, 356 rpm)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

16. A centrifugal pump runs at 1540 rpm and discharges 120 litres per second against a head of 25 metres. If the diameter of the impeller is 25 cm and its width is 8 cm, find the vane angle at the The manometric efficiency of the pump is 75%. (32 30) outer periphery. 17 A centrifural pumn
1- A double jet of Pelton turbine driven by double nozzles to produce (4250 kw) to the shaft of an electrical generator when running at (400 rpm). The height of (180 m). wheel diameter is (1450 mm). The velocity of relative= 0.9 of jet velocity. If the angle of bucket is (165'), determine: a) Hydraulic efficiency b) Diameter of the jet
PROBLEM 5 An axial flow pump is required to deliver 1m3/s at 7m head while running at 960 rpm. Its outer diameter is 50 and hub diameter is 25 cm. Find the following: (1) flow velocity, which is assumed to be constant from hub to tip, and A. 4.59 m/s B. 6.791 m/s C. 60.7 m/s D. 39.3 m/s (2) power required to drive the pump if overall efficiency is 84%. A. 81.75 kW B. 12.03 kW C. 40.7 kW D. 60.9 kW
A Francis water turbine has a runner of 1m outer diameter. It rotates at a speed of 160 rpm, flow velocity is 2.8 m/s and the supply head is 10 m. The flow is radial at exit. The turbine efficiency is 89%. Find the guide vanes angle (a₁) and the vanes angle at inlet (B₁).
A Pelton wheel develops 70 kW under a head of 60 m of water. It rotates 400 rpm. Overall efficiency is 80%. Find the discharge rate in m³/s. Use the equation below, where P is power of the turbine shaft and no is the overall efficiency, where specific weight of water is is 9.80 kN/m³ no P YQH A generator is driven by a small, single-jet Pelton turbine designed to have a power specific speed sp 0.20. The effective head at nozzle inlet is 200 m and the nozzle velocity coefficient is 0.985. The runner rotates at 880 rev/min, The turbine overall efficiency is 80%. Find (a) the power delivered by the shaft of the turbine and (b) find the power delivered by the water to the turbine. where density of water is 1000 kg/m³ and g is 9.80 m/s². Use Stup Ω P/p (gHE)* Overall efficiency ne and Power developed at turbine shaft hydraulic power P YQH
An axial flow pump discharges water at the rate of 78 m³/min and runs at 550 rpm. The total head is 10 m. Assume blade velocity of 22 m/s, flow velocity of 4.5 m/s, hydraulic efficiency of 0.87, and overall pump efficiency of 0.83. Calculate Cr OP 3.1. The power delivered to the water, and power input The impeller hub diameter and tip diameter 3.2. 3.3. The inlet and outlet blade angles for the rotor 30 07:30 S
A Kaplan produces 60 MW, water available head of 40 m with an overall efficiency of 85%. The speed ratio is 1.6 and flow ratio 0.5 and hub diameter is 0.35 times the tip diameter. Determine the mean speed of turbine.
Asap
A Francis turbine develops 500 kW at 500 rpm under a head of 50 m. The hydraulic efficiency is 95% and the overall efficiency is 85%. The flow ratio is 0.20cand the ratio of width to diameter is 0.15. The blades occupy 5% of the outlet area and the inside diameter is half of the outside diameter. Find the guide blade angle at inlet, blade angles at inlet and outlet. The velocity of flow at inlet and outlet are equal.
A supply water is available at a head of 684 meters. It is proposed to build a turbine to operate at 6 rev/s and develops 14.92 MW.Compute the specific speed in rpm.a. 3297rpmb. 4356rpmc. 6568rpmd. 3477rpm
A Petlon Wheel having semicircular buckets and working under a head of 150 m runs at a speed of 600 rpm. If the discharge through the nozzle is 45 lit/s. Find the power available at the nozzle and the hydraulic efficiency. Take wheel diameter as 0.5 m and C,, for the nozzle as 0.98.
A. A water jet of diameter 180 mm impinges on the buckets of a Pelton turbine having overall efficiency of 85% while operating under a net head of 500 m and at speed of 420 rpm. Find the specific speed of the turbine. Take coefficient of velocity of the jet as 0.98 and speed ratio as 0.46. B. The pitch circle diameter of a Pelton wheel is 0.9 m. A jet of water of diameter 80 mm gets deflected by an angle of 170° when it impinges on the buckets. The bucket friction coefficient and coefficient of velocity of jet can be taken as 0.93 and 0.97 respectively. If the net head available on the wheel is 500 m and speed ratio is 0.45, calculate (a) the power transferred to to the wheel by the jet, (b) hydraulic efficiency, and (c) specific speed of the turbine. Take mechanical efficiency of wheel as 0.9.