need correct and urgent V (2)3.94is 2.0 m wide as shown in Fig. P3.94. The up-stream depth is 70 mm. The water surface rises40 mm as it passes over a portion where the chan-njlj bottom rjsejs 10 mm. If viscous effects arenegligible. what is the flowrate?Water flows in a rectangular channel that100 mm(1)Q 70. mm10 mmFIGURE P3. 94

Answered: Image /qna-images/answer/c4145b89-b848-45ea-930c-5ec9012440d5.jpg

3.94 Water flows in a rectangular channel that is 2.0 m wide as shown in Fig. P3.94. The up- stream depth is 70 mm. The water surface rises 40 mm as it passes over a portion where the chan- nel bottom rises 10 mm. If viscous effects are negligible. what is the flowrate?

3.94 Water flows in a rectangular channel that is 2.0 m wide as shown in Fig. P3.94. The up- stream depth is 70 mm. The water surface rises 40 mm as it passes over a portion where the chan- nel bottom rises 10 mm. If viscous effects are negligible. what is the flowrate?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. Consider a rectangular channel section having a length of 500 feet. The width of the channel is…

Q: For the flow situation below whereby saturated unit weight of soil is 19.62 kN/m^3 and unit weight…

Q: 4. Determine the dimensions and the critical depth of the following open channels cross-sections of…

A: Given information in question Area Discharge Angle made by side of trapezoidal channel To find out…

Q: Problem #3 Hydraulic Jump A hydraulic jump occurs in a rectangular channel 4.0 m wide. The water…

Q: The flow rate in a channel with area of 25 m2 has an average depth of 3 meters - was recorded at…

A: Given that Flow rate =Q= 200 m3/s Area of channel= A= 25 m2 Depth = y= 3 m first of all we have…

Q: 11. The depth and widths of a rectangular channel are 4m and 5m respectively. Determine the…

A: To find the hydraulic radius (R)-

Q: A downward step of height 0.5 m causes a hydraulic jump in a wide channel when the depth and…

A: Given :

Q: Sketch the Specific Energy Diagram, and show that for a given open channel and discharge, the Spec…

A: The Specific Energy Diagram is shown below: The assumptions are: 1. The channel bed is horizontal.…

Q: at a depth of 360 mm. A hydraulic jump occurs and the depth of water downstream from the

A: Given data- Width(B) = 5m Depth(y1) = 360 mm = 0.36 m Hydraulic jump(y2) = 1300 mm = 1.3 m

Q: .Water emerges from an ogee spillway with velocity = 13.72 m/s and depth = 0.3 m at its toe. The…

Q: Problem 4 isosceles trapezoidal channel of bottom base of width 3 m and sides sloping 1:1 in channel…

Q: Question: The 1 meter wide rectangular cross-section open channel system, whose longitudinal profile…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: the incoming flow rate is 100m3/s on a rectangular channel with: depth = 3m width = 4 meters Then, a…

A: Using conjugate alternate depth formula

Q: 1. The discharge and velocity of water in a rectangular channel are 75m^3/s and 5m/s respectively.…

A: To find : Hydraulic radius.

Q: Water flows over a concrete spillway into a rectangular channel 9 m wide through a hydraulic jump.…

Q: Determine the hydraulic radius in meters if the total bottom width is 20 meters. Total Base width 3m

A: This problem is related to Fluid mechanics. In this problem given about the dimensions of Tank and…

Q: (B) In a rectangular channel, water flows under the partially opened sluice gate. If the water has…

A: step 1-

Q: Part 1: Determine the Froude number and the type of flow. Water flows at a rate of 8.5 m3/s in a…

A: Water flow rate = 8.5m3/sec Width of channel = 2.25m Depth of channel = 0..32m It has been asked in…

Q: A- In a rectangular channel, a hydraulic jump occurs at a point where depth of water before and…

Q: In the case of a rectangular channel 3 m wide and 1 m deep, the value of Manning's constant is 0.022…

A: step 1-

Q: Compute for the Froude number when the velocity of flow is 2m/sec in a rectangular channel measuring…

Q: Water flows in a long, 2.50 m wide rectangular channel at a uniform flow depth of 1.07 m and a…

Q: 6. Find the discharge through totally drowned orifice of width 3.3 m if the difference of water…

Q: If the water depth immediately upstream or downstream of the hydraulic jump in a rectangular channel…

A: V=1m/s To find conjugate depth

Q: Example: A rectangular channel 5.5 m wide conveys water of 16.5 m/sec at a depth of 1.5 m: a) What…

A: Thank you for the question. As per honour code we are allowed to answer three subparts at a time so…

Q: 2. A rectangular channel 4 m wide flows at a flow rate of 10 m^3/s at a depth of yt=2.5m.lf the…

Q: 3.1. A trapezoidal channel convey 15 m³/s of water on a bed slope of 1 in 200. The base width of the…

A: As per our guidelines we are supposed to answer only one question. Kindly repost the other questions…

Q: Water on the horizontal apron of the 30 m -wide spillway shown in Fig. E10.8a has a depth of 0.2 m…

Q: 13. (LAB) A discharge of 25 m/s is passing in a rectangular channel of bed width 8.0 meters and…

A: Hydraulic jump: The hydraulic jump occurs in the open channel flows. The flowing water is having…

Q: EXAMPLE 1: Determine the normal discharge for the channel shown in Fig 2.7a. The water surface in…

A: Flow in most channels is turbulent, and laminar flow in open channels is very rare. Laminar…

Q: fficient section if the wetted area is 1.0 square meters. Draw the cross section of the channel with…

A: Given- A=1m2 θ=45°

Q: Question 4: Water flows at a rate of (20+b) m³/s with 2 m depth and (5+a) m wide rectangular…

Q: A trapezoidal channel 6.3 m wide and 1.1 m water depth has a bed slope of 1 in 900 and side slope of…

Q: Water flows in a 5-ft-wide rectangular channel with a flowrate of Q = 30 ft³/s and an upstream depth…

Q: Water flows over a concrete spillway into a rectangular channel 9 m wide through a hydraulic jump.…

A: The answer is found to be Discharge= 93.70 m^3/s For explanation please refer the attached solution,…

Q: Find the rate of flow in m3/sec/m through the permeable soil layer. Given: H = 5.5 m, H1 = 2 m, h =…

A: Given values: Permeability of soil= 0.085 cm/s Soil layer thickness = 5.5 m Width of the soil layer…

Q: Q2/ Water flow in rectangular section at the flow rate of (3 m³/sec ) at width of (1 m), the depth…

Q: 8 m³/s discharge flows through 4 m wide rectangular channel at a velocity of 2 m/s. The hydraulic…

A: Given:- Discharge, Q=8 m3/sWidth of rectangular channel, w=4 mVelocity, V=2 m/s To find:- Hydraulic…

Q: A 170-m long pipeline, composed of two pipes connected in series, discharges freely at a point 40 m…

Q: 5) A hydraulic jump occurs in a rectangular channel 3 m wide. The water depth after the jump is 2.0…

A: Given data Width Depth after jump Bottom slope Roughness coefficient

Q: 2. Flow occurs through a sand-filled pipe with a cross- sectional area of 60 cm?. If K is 10 cm/s…

Q: In a rectangular channel, if the water depth just upstream or downstream of a frictionless vertical…

A: Given :- A rectangular channel is given Water depth just upstream or downstream of a friction less…

Q: The depth of flow of water at a certain section of a 5 m wide rectangular channel is 0.6 m and the…

A: Given: Width = 5 m Depth of flow before jump = 0.6 m Flow rate = 21 m3/s

Q: The depth of flow of water at a certain section of a rectangular channel 4 m wide is 0.5 m and the…

A: Given: Width = 4 m Depth of flow before jump = 0.5 m Flow rate = 16 m3/s

Q: 6) Water flows down spillway at the rate of 12 m/s per meter of width into a horizontal channel,…

A: Discharge per meter width q=12 m3/s/m.Velocity v1 = 20 m3/s/m. y1=qv1 =1220=0.6 m.

Question

need correct and urgent

V (2)
3.94
is 2.0 m wide as shown in Fig. P3.94. The up-
stream depth is 70 mm. The water surface rises
40 mm as it passes over a portion where the chan-
njlj bottom rjsejs 10 mm. If viscous effects are
negligible. what is the flowrate?
Water flows in a rectangular channel that
100 mm
(1)
Q 70. mm
10 mm
FIGURE P3. 94

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the water flow over the spillway, the velocity is uniform at sections 1 and 2 and the pressure approximately hydrostatic. Neglecting loses, compute v1. Assume unit width. 6m 2 1m
Size the channel for a mechanically cleaned coarse bar rack for a flowrate of 40,000 m/d. The bar rack will be set at an angle of 75 degrees from horizontal and will have clear bar spacing of 12 mm. The bar rack uses 12-mm-wide by 25-mm deep bars. The upstream chan- nel velocity should be greater than 0.4 m/s. Determine the headloss through the bar rack for the clean screen and for a screen that is 50 percent clogged.
Q-2 Water flows through a vertical contraction (venturi) section. Piezometers are attached to the upstream pipe and minimum area section as shown. The velocity in the pipe is 3 m/s. The difference in elevation between the two water levels in the piezometers is 15 cm. What is the velocity at the minimum area? 15 cm 3 mis
Water flows in a long, 2.50 m wide rectangular channel at a uniform flow depth of 1.07 m and a uniform velocity of 1.68 m/s. The hump height is 0.75 m. a. Calculate the flow depths immediately before, on top of, and immediately after a smooth hump on the channel bed. b. Calculate the force exerted by the flow on the hump.
In Eig. 5a below, the flow rate is 1.2 m³/s per meter of channel width. (a) Compute the velocity and water depth at the top of the budge (hma= 0.1 m). Characterize the flow there. (b) Rework the problem for a flow rate three times as large. 1 + 'o + V(x) Yo =0.85m y(x) Bulge h(x) Fig 5a
23. Water flows in a triangular channel at a depth of 0.90 m. A hydraulic jump occurs at a depth just downstream of the jump is measured to be 1.8 m. The apex angle is 90°. Calculate the discharge of the triangular channel (apex down). 24.If water is flowing in a rectangular channel 30 ft wido Trith tho digoh
A triangular duct flows partly full having a bed slope of (0.004) as shown in Fig. (1) below. If the flow depth is (0.6 m), and manning's n= 0.016, compute: 1- Top width 2- Discharge 3- Is the flow subcritical or supercritical? 4- Is the flow laminar or turbulent? 1 m 1m
A circular conduit is to satisfy the following conditions: Capacity when flowing full is 0.13 m³.sec¹, velocity when the depth is one quarter of the diameter is 0.6 m.sec¹¹. Assume the flow is uniform and determine the diameter and the slope of the pipe if you know that Chezy's coefficient is 58 mº.5 sec¹? Answer// D= 460 mm; S= 0.00158
13. Compute the critical depth for a rectangular canal having a critical velocity of 4 m/s.
: The width of a horizontal, rectangular channel is reduced from 3.5 to 2.5 m and the floor is raised by 0.25m in elevation at a given section. At the upper stream section the depth of flow is Im and the KE correction factor is 1.15. If the drop in water level at the contraction is 0.20m. Calculate loss is i) Discharge if energy • zero. ") Discharge if energy loss is 10th of the upper stream velocity head. KE correction factor for contracted section is unity. 2m y₁ 0.2m y: 2 0.25 m. 3.5 2.5m
Q3/ Determine the state of flow in a rectangular channel of (3m) width and depth of flow is (1m) and the bed slope is (1 in 2500 ) for the following two cases: * 1- friction factor is (0.038). 2- Kuttur constant is (0.013). f نوع الي
A circular conduit is to satisfy the following conditions: Capacity when flowing full is 0.13 m³.sec¹, velocity when the depth is one quarter of the diameter is 0.6 m.sec¹¹. Assume the flow is uniform and determine the diameter and the slope of the pipe if you know that Chezy's coefficient is 58 m0.5.sec-¹?