31. A truck develops 33.5 hp at 1000 rpm. The clutch used to transmit the aforementioned power is a single plate clutch with two pairs of contact surfaces. If the coefficient of friction is to be 0.40 and the mean diameter of the disk if to be 190 mm, and the average normal stress on the clutch lining is 120 kPa, compute the inside diameter. A. 234 mm B. 147 mm C. 120 mm D. 110 mm

31. A truck develops 33.5 hp at 1000 rpm. The clutch used to transmit the aforementioned power is a single plate clutch with two pairs of contact surfaces. If the coefficient of friction is to be 0.40 and the mean diameter of the disk if to be 190 mm, and the average normal stress on the clutch lining is 120 kPa, compute the inside diameter. A. 234 mm B. 147 mm C. 120 mm D. 110 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q) A single plate clutch has to transmit 75 kW at 3000 r.p.m. The spring exerts an axial pressure of 7.35 N/cm3. Determine the inner and outer diameters of the friction surfaces if the ratio of the two diameters is 1.5.
Q2/ A dry single plate clutch is to be designed for an autontotive vehicle whase engine is ated to give 100 &W at 2400 r.p.M. and marimum torque 500 N-m. The outer radus of the friction plate is 25% ore than the inner radius, The intensity of pressure berween the plate is not to exceed 0.07 N/mm. The coefficient of friction may be assamed egual t0 0.3 The helical springs reguired by this cluich to provide axial force mecessary to engage the clutch are eight. If cach spring has stiffness equal to 40 N/mm, derermine the dimensions of the friction plate and initial compression in the springs
A cone clutch is to transmit 30 kW at 1250 rpm. The face angle of the cone clutch is 12.5o and the mean diameter is to be 355mm. The coefficient of friction between the contacting surfaces is 0.20 and the maximum normal pressure is 83 kPa, determine the outside diameter of the clutch. a. 384.3 mm b. 356.2 mm c. 349.5 mm d. 339.2 mm
Situational Problem ( 3 - 4) An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a single plate clutch with two pairs of contact surfaces. The coefficient of friction is 0.4 and the mean diameter of the disk is to be 190 mm. The average normal stress on the clutch lining is 120 kPa. 3. Determine the axial force to engage the clutch based on uniform wear. A. 1.57 kN B. 3.14 kN C. 5.28 kN D. 7.46 kN
A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately steel and phosphor bronze and they run in oil. The coefficient of friction is 0.071. The mean axial pressure is 0.14 N/mm? and the internal radius of the friction surfaces is 0.8 of the external radius, which is 125 mm. Find out the number of plates reauirod
A A multiple disc clutch transmits 55 kW of power at 1800 r.p.m. The coefficient of friction is 0.1 and the axial intensity of pressure is not to exceed 160 kN/m. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque.
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
In a thrust bearing, the external and the intermal diameters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m?. The shaft rotates atę Op rpm. Taking the coefficient of friction as 0.os, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
Q1/ A plate clutch having a single driving plate with contact surfaces on each side is required to transmit 110 kW at 1250 r.p.m. The outer diameter of the contact surfaces is to be 300 mm. The coefficient of friction is 0.4. (a) Assuming a uniform pressure of 0.17 N/mm? ; determine the inner diameter of the friction surfaces. (b) Assuming the same dimensions and the same total axial thrust, determine the maximum torque that can be transmitted and the maximum intensity of pressure when uniform wear conditions have been reach.
A soft surface cone clutch must handle 1865 In-1b of torque at 1250 rpm. The large diameter of the clu is 13.75 in. and the included angle in 12.5°. The face width of the bearing surfaces is 2.5 in. Using efficient of friction 0.20. determine (a) the force (F) to engage the clutch, (b) the required normal unit pa sure on the contact surfaces when operation is at capacity Ans. 428 lb. 13.15 psi
An engine developing 40 hp at 1250 rpm is fitted with a cone clutch built into the flywheel. The con a face angle of 12.5 degrees and a mean diameter of 14 in. The coefficient of friction ta 0.20 and the n pressure on the clutch face is not to exceed 12 psl. Determine the required face width and the force m sary to engage the clutch, assuming uniform wear. Ans. 2.96 in.. 592 lb
Example: An automotive single-plate clutch ,with two of friction Surfaces, transmits a 300 N-mto- pairs rque at 1500 rip.m. The inner and outer diameters of the friction disck are 170 and 270 mm The cofficient of friction is o.35. The normat for- ce on the frichion Surfaces is exerted by nine helical Compre ssion springs, so that the clutch is a lways engia- ged. The clutch is dis engaged when the external force Further Compresses the (5) and the number of active Coile are (6). The Springs are madeof patented and cold -drawn steel wires of minimum tensile Strength (MTS) (N/mm²) as respectively. springs. The spring Lindex is Wire dia. 1 d(mm) 1.21.4 1.6 1.8 2 2.5 3 3.6 44.55 67 IMIm?1900 |1360|182|1480175011구20116401157이 1510|1480|144011390132011260 MTS permissible shear stress for the of the ultimate tensile strength, and (G-81370 Nlmné). Design the springs and specily their dimensiuns. Use this relation to obtaine to the total normal force required to transmit the torque. F Dis outer…