4-11. Compute the pressure in the pipe at the location shown on Figure 4-17. The flow rate through the pipe is 10,000 L/hr. The pipe is commercial steel pipe with an internal di- ameter of 50 mm. The liquid in the pipe is crude oil with a density of 928 kg/m³ and a vis- cosity of 0.004 kg/m s. The tank is vented to the atmosphere. 10,000 liters per Hour 3 m Vent 3 m Leak Occurs Here Figure 4-17 Process configuration for Problem 4-11.

4-11. Compute the pressure in the pipe at the location shown on Figure 4-17. The flow rate through the pipe is 10,000 L/hr. The pipe is commercial steel pipe with an internal di- ameter of 50 mm. The liquid in the pipe is crude oil with a density of 928 kg/m³ and a vis- cosity of 0.004 kg/m s. The tank is vented to the atmosphere. 10,000 liters per Hour 3 m Vent 3 m Leak Occurs Here Figure 4-17 Process configuration for Problem 4-11.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mechanical-Energy Balance and Friction Losses. Hot water is being discharged from a storage tank at the rate of o.223 ft3/s. The process flow diagram and conditions are the same as given in Example 2.10-6, except for different nominal pipe sizes of schedule 40 steel pipe as follows. The 20-ft-long outlet pipe from the storage tank is 1-in. pipe instead of 4-in. pipe. The other piping, which was 2-in. pipe, is now 2.5-in. pipe. Note that now a sudden expansion occurs after the elbow in the 13-in. pipe to a 2}-in pipe.
Based on the layout of the water supply system, as show in Figure 1, the pressure, in psi, is estimated be 46 at the faucet in the and floor of the residential building. Consider flow through the delivery pipe, Q = 1.50 cfs and diameter of the pipe, D = 2.65 inch with e = 0.015 inch. Ingore the minor pressure losses and use the following formulae to calculate the major pressure losses. The additional power in hp required to provide the recommended pressure of 58 psi at the building is nearly. Assume f = 0.0175. Use g = 62.4 lb/f3 for water. Water temperature is 20°C (68°F).
Compute the Cross sectional area of Pipe Discahrge=0.8 m3/s Velocity=2 m/s
3. Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50 mm, the density of water is 998 kg/m', the volumetric oil flowrate is 720 L'min, and the dynamic viscosity of water is 1.2 centipoise
What is the time is taken by the system to fill a tank of capacity 315 liters and flow rate 25 x 10 3 m³ per hour?
Compute points on the velocity profile from the pipe wall to the centerline of a 3/4-in Type K copper tube if the volume flow rate of water at 60'F is Q 0.5 gal/min. Use increments of 0.05 in and include the velocity at the centerline. please be through and provide all calculus and graphs/tables
Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
As shown in the figure, the water flows from the ground floor of a three-storey house to the second floor through pipes of 20 mm diameter (average roughness of the pipe material = 0.0015 mm) at a volumetric flow rate of 0.75 L / s. Water is discharged from the system to atmospheric pressure through a tap with a 12 mm diameter outlet. There are 4 winged elbows, one ball valve and one faucet throughout the installation. Calculate the effective pressure at point 1. (pwater=998 kg/m3, uwater=1.12x10-3 Pa s, g=9.81 m/s2)
Three pipes A, B and C are interconnected as shown in Figure 1. The pipe dimensions are as follows : 1)Find the the rate at which water will flow in each pipe, ignoring the shock losses at P 2)Find the pressure at P
Industrial pipes Do the guides allow movement of a pipe only in two directions (in a plane)?
Gasoline at 77°F flows from a pressurized upper tank to a vented lower tank as shown in the figure below. A length of 1-inch Schedule 40 pipe connects the two tanks a Calculate the air pressure (in psi) above the gasoline in the upper tank that will result in a flow rate of 35 gpm into the lower tank for the dimensions shown The head loss due to pipe friction is 52.8 feet and you DO NOT need to calculate this! As the upper tank drains does the air pressure in the upper tank need to be neld constant to maintain the flow rate at 35 gpm? Briefly explain your answer. C The pressurized upper tank is converted to an atmospheric tank and a pump is installed in the system. If flow rate and pipe friction remain the same, how much horsepower does the pump put into the system?
Answer the question considering the information given in the image. Explain each step a)Calculate the Reynolds number for the flow in the pipe.