4. The resisting area of the body against axial stress is perpendicular to the orientation of the internal force. O O 5. The resisting area of the body against bearing stress is perpendicular to the orientation of the force. O True False O O True False 6. To be safe, strength of material is less than the actual stress. True False

4. The resisting area of the body against axial stress is perpendicular to the orientation of the internal force. O O 5. The resisting area of the body against bearing stress is perpendicular to the orientation of the force. O True False O O True False 6. To be safe, strength of material is less than the actual stress. True False

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

il Engineering Dept. /Second Year "Strength of Materials" Home Works: A flat steel bar has axial loads (forces along the centroidal axis of the bar) applied at points A, B, C, and D, as shown in Fig. a. If the bar has a cross-sectional area of 3.00 in.², determine the normal stress in the bar (a) On a cross section 20 in. to the right of point A. (b) On a cross section 20 in. to the right of point B. (c) On a cross section 20 in. to the right of point C. Figure (a) 81 kip 30 in. 45 in. OA BOC 18 kip 54 kip 40 in. (a) Do Prof. Dr. Qais Fadhil 45 kip
B. Shear stress.
PROBLEM 37: A sieel secion havung a Cioss seciion c: 20 mm x 30 mm is subjected to an axial force of 240 KN The steel section has produces a strain of 0.002. If it has a value of Poissons ratio of 0.30.Find the shear modulus a. 76923 MPa b. 73852 MPa C. 78023 MPa d. 80256 MPa
Asap Determine principal stress.
#11 Normal stress in rods 1 and 2
Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load P-75 KN is applied. Neglect the deformation and mass of the horizontal bar AB. Use Ea = 75 GPa, as=23.0 um/m °C. Aa 850 mm2 Es 210 GPa, as = 11.9 um/m.°C and As 650 mm2. %3D Steel Aluminum 2.5m 3m 3m 3 m 3m 75 kN
8 KN 2m 3m 6KN. Am 3m, 3m A B 2m 6KN cross-Section 300mm 150mm Only considering stresses that are normal to the cross-sections you're designing. Where omax is the maximum value of stress developing in the cross-sections. Calculate omax
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
(5) This simply-supported beam has been subjected to an applied moment at midspan. The M(x) equations have been supplied for you. You are to write the v(x) equations for 0
(32 H.W Find longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal pressure. is 0.9 MPa and thickness of Wall is 6.4mm ? Ans: 6 = 42.19 MP₂ °H = 62.8 Mra 4 Also find I ?=0.67 Alir G 0.6m fot TE L = 1.8m O 7 0.6m
Find the stress..
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?