. Two members of a truss apply the forces shown to the gusset plate. a. If the Resultant of these forces is horizontal, determine P. b. Knowing that P = 12,200 lb, determine the resultant of these forces.

. Two members of a truss apply the forces shown to the gusset plate. a. If the Resultant of these forces is horizontal, determine P. b. Knowing that P = 12,200 lb, determine the resultant of these forces.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter3: Resultants Of Force Systems

Section: Chapter Questions

Problem 3.17P: The 3200-1b weight is supported by two cables. Knowing that the resultant of the cable tensions T1...

See similar textbooks

Related questions

Q: The truck carries the spool which has a weight of 460 lb and a radius of gyration of kg = 2 ft.…

Q: 3. A rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the…

Q: 13. Shown in the figure is a section through a balcony. The total uniform load of 600 kN is…

Q: 5-37C A glass manometer with oil as the working fluid is connected to an air duct as shown in Fig.…

A: It is needed to determine which diagram is correct as per the given flow condition.

Q: Problem 2.154: Critically Damped Torsional Vibration The needle indicator of an electronic…

A: For critically damped instrument the damping constant is equal to twice the product of inertia and…

Q: A rotating machine of 400 kg is similar to the system shown below. It operates at 3600 rpm (note: 1…

A: Given data: M=400 Kgm=4 KgN=3600 rpmK=8*106 N/mC=2*104 Ns/me=20 cm

Q: A two degree of freedom damped system has natural frequencies 2 rad/s and 3 rad/s and corresponding…

Q: A 75 mm diameter jet of an oil having specific gravity 0.8 strikes a normally stationary flat plate.…

A: Given data:- Diameter of the jet (d)=75 mm Specific gravity of the oil =0.8 Force exerted (F)= 1200…

Q: Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow…

Q: A 4-kg collar A is at rest on a spring with stiffness k1 = 310 N/m, but the spring is not connected…

A: The initial compression in the bottom spring can be determined as shown below. W=k1x14 kg9.81…

Q: 6.92* At a particular axial position, the beam whose cross section is shown is subjected to a shear…

A: Given: Shear force: →V=40 KN=40×103 N Radius of the inner circle→r1=50 mm Radius of the outer…

Q: An oil having viscosity 0.08 N S/m², Specific weight 8829 N/m, density 900 kg/m flow at the rate of…

Q: Compute the mass fractions of a ferrite and cementite in pearlite. Assume T 726 C°. W₁ = WFe3 C i =

A: Given: T = 726 C To find the mass fraction of α ferrite and cementite in Pearlite

Q: Two kilograms of air within a piston-cylinder assembly execute a Carnot power cycle with maximum and…

Q: A winch mechanism with a handle length of 30 cm and a drum diameter of 8 cm is used to lift a 45 kg…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 3) A hot cup of coffee at 90 °C is placed on the table in a room at 22 °C. After some time a thermal…

A: During thermal equilibrium between coffee and it's surrounding, heat lost by coffee will be equal to…

Q: A closed container contains 1.5m high of water, 2.5m high of oil (SG= 0.8), an unknown liquid (SG=…

Q: able weighing 25 newtor per meter length is suspended hall pulley at B. Calculate the mass m of the…

A: Given-Information:- Length, AB = 100 m Length, BC = 12 mWeight of cable, W = 25 N/mSag = 9 m…

Q: A spherically symmetric object, with radius R = 0.70 m and mass M = 1.5 kg, rolls without slipping…

A: Given data:- A spherically symmetric object, with radius R = 0.70 m mass M = 1.5 kg, velocity V =…

Q: Case 1 1.3. dia=4 mm dia=2 mm dia=4 mm V Case 2 dia=2 mm, X 14 mm Case 3 dia=4 mm dia=8 mm dia=4 mm…

Q: When a u-tube (manometer) is connected to the atmosphere on one side and a pressurized tire on the…

A: It is asked to choose correct answer from given option when u-tube manometer is connected to…

Q: Required information Heat dissipated from an engine in operation can cause hot spots on its surface.…

Q: Consider a 102 mph airflow over a flat plate with a span of 9.7 ft and a planform area of 60 ft2.…

Q: 11) A support block is acted upon by two forces as shown. Knowing that the coefficients of friction…

A: Given data as per question μs=0.35μk=0.25

Q: In (Eigure 1). P₁ = 12 kN and P₂ = 18 kN. Determine the components of reaction at D. Figure nih 4 m…

Q: The mass flow rate is m, the volume flow rate is, density is 1 P₁ □A.V=m/v B.m=Vlp OC.V=m/p OD.m=V/v…

A: We know mass density , ρ = m/V V=mp

Q: Engineer Batman asked a steel manufacturer for a specialty item where he will carve his monument. He…

Q: If the tank is held so that the top is 3.0 m below the surface of water, what is the force on the…

A: Write the given diagrams.

Q: Catalogue data of a water-cooled condenser of a manufacturer gives the following details:…

Q: A compressor is a device that can_ A. consume work from external devices B. produces work to…

A: ANS): option A & D Consume work from external device Increase the working fluid pressure…

Q: E דך 74 360 mm 450 mm 60° B, 002 D OC = 140 mm AD = 800 mm DE = 250 mm ₂= 21 rad/s B on slider C on…

Q: The disk is originally rotating at wo = 8 rad/s and is subjected to a constant angular acceleration…

Q: Please give the answer as in the format asked

Q: 16–109. The ends of bar AB are confined to move along the paths shown. At a given instant, A has a…

Q: Water vapor enters a nozzle at 400 °C and 800 kPa, with a speed of 10 m/s, and leaves at 375 °C and…

A: Given data and to be determined variables. T1=400 °CP1=800 kPaC1=10 m/sT2=375 °CP2=400 kPaQl=25…

Q: 8-93. If a force of P = 30 N is applied to the handle of the lever, determine the largest couple…

Q: Compute the mass fraction of eutectoid ferrite in an iron-carbon alloy that contains 0.60 wt% C. The…

Q: Problem 2.121: Variation of Displacement Find the variation of the displacement with time, x(t), of…

Q: 4. A tank contains 80 gal of pure water. Brine solution with 2 lb/gal of salt enters at 2 gal/min,…

Q: An overheating vehicle is being discussed. Technician A states that the vehicle may be overheating…

A: The part that gathers some of the hot coolant from your engine and directs it to the heater core…

Q: can you send me a written solution?

Q: A 14m bar of negligible weight rest in a horizontal position on the smooth planes as shown. Compute…

Q: For the translational system shown as figure. (1) Give the differential equations of the system or…

Q: As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported…

A: Given data: T0=10°C∆=0.18 mmT=95°CFor each copper bar:A=500 mm2E=120 GPaα=16.8 μm/m°CFor each…

Q: Hot working is a good way to shape brittle material 1) True 2) False

A: It is true that hot working is a good way to shape brittle material.

Q: (a) Establish whether the 3D truss shown below is statically determinate. Justify your answer mathe-…

A: Given: There are total 7 members of the structure in which one is the fixed member. So the number of…

Q: If the Radius of a elbow is 6”, and the duct Diameter is 3”, what is the loss factor if the elbow is…

A: Given data :- the Radius of an elbow (R)= 6 in the duct Diameter (D) =3 in To find :- the loss…

Q: B

A: Given,

Q: A four-stroke cycle engine have an indicated mean effective pressure of 190 lb/in2, a stroke of 6…

Q: Determine the product of inertia Iay for the slender rod of mass m.

Question

100%

4. Two members of a truss apply the forces
shown to the gusset plate.
a. If the Resultant of these forces is
horizontal, determine P.
b. Knowing that P = 12,200 lb, determine
the resultant of these forces.
8000 lb
65°
35°
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.3) Determine the equivalent force R. if the magnitudes of the three forces acting on the plate are T, - 90 kn, t, - 60 kN, and T, - 40 kn.
Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as shown, determine the magnitude F of the equal forces exerted on the four contact points on the 1-in. bolt head so that their external effect on the bolt is equivalent to that of the two 50-lb forces. Assume that the forces are perpendicular to the flats of the bolt head. 1"- A 50 lb A C View C Detail (clearances exaggerated) 14" 50 lb 14"
A steel tank is to be positioned in an excavation. Knowing that the magnitude of P= 500 lb, determine the required angle a if the resultant R of the two forces applied at A is to be vertical. Also, determine the corresponding magnitude R. 425 lb 30°
ASSIGNMENT 1 Determine the Resultant of the Forces in the system below. yT 1250KN 726 KN 65° 4 x 318 KN DUE A THURSD
A barge is pulled by two tugboats. The barge is aligned horizontally while the rope of tugboat 1 is inclined with the horizontal 0-degrees upward, and rope of tugboat 2 is inclined with the horizontal 'a'-degrees downward. If the resultant of the forces exerted by the tugboats is a 6,261-lb force directed along the axis of the barge and 0=36 degrees, determine the magnitude of the tension (Ib) in rope 1 if a = 51° Answer in 2-decimal places only if applicable, and don't include units. A
Q2. Determine the x and y components of each of the forces shown. 60 lb 25° 60° 50° 40 lb 50 lb
Q1): The cable stays AB and AD help support pole AC. Knowing that the tension is 120 Ib in AB and 40 Ib in AD. Determine the magnitude and the direction of the resultant of the forces exerted by the stays at A. 10 ft В D 8 ft to 6ft
Q1): The cable stays AB and AD help support pole AC. Knowing that the tension is 120 lb in AB and 40 lb in AD. Determine the magnitude and the direction of the resultant of the forces exerted by the stays at A. 10 t sit -6 it Q2): 425 A steel tank is to be positioned in an excavation. Knowing that the magnitude of P is 500 Ib, determine by trigonometry (a) the required angle a if the resultant R of the two forces applied at A is to be vertical, (b) the corresponding magnitude of R.
Q2): A telephone cable is clamped at A to the pole AB. Knowing that the tension in the left-hand portion of the cable is T = 800 lb, determine by trigonometry (a) the required tension T2 in the right-hand portion if the resultant R of the forces exerted by the cable at A is to be vertical, (b) the corresponding magnitude of R. 25°
Q1): The cable stays AB and AD help support pole AC. Knowing that the tension is 120 Ib in AB and 40 Ib in AD. Determine the magnitude and the direction of the resultant of the forces exerted by the stays at A . 10 ft B. 8 ft 6 ft
The man exerts a force P of magnitude 150N on the handle of the wheelbarrow. Knowing that the resultant of the force P, Q, and W (wt of the wheelbarrow) is zero, determine W.
Q 2. Four ropes are attached to a crate and exert the forces shown. If the forces are to be replaced with a single equivalent force applied at a point on line AB, determine (a) the equivalent force and the dis- tance from A to the point of application of the force when a = 30°, (b) the value of a so that the single equivalent force is applied at point B. 160 Ib 100 lb 46 in. B 25 400 lb 36 in. 90 lb 65° D 10 in. C 66 in.