4.14 The incremental fuel costs for two generating units G, and G, are given by IC, = 25 + 0.2 PG, and IC, = 32 + 0.2 PG, where PG, and PG, are real powers generated by the %3D units. The economic allocation for a total load of 250 MW, neglecting transmission loss, is given by (a) PG, = 142.5 MW and PG, = 107.5 MW %3D %3D (b) PG, = 109.75 MW and %3D PG, = 1140.25 MW %3D (c) PG, = 125 MW and PG, = 125 MW %3D (d) PG, = 100 MW and PG, = 150 MW

4.14 The incremental fuel costs for two generating units G, and G, are given by IC, = 25 + 0.2 PG, and IC, = 32 + 0.2 PG, where PG, and PG, are real powers generated by the %3D units. The economic allocation for a total load of 250 MW, neglecting transmission loss, is given by (a) PG, = 142.5 MW and PG, = 107.5 MW %3D %3D (b) PG, = 109.75 MW and %3D PG, = 1140.25 MW %3D (c) PG, = 125 MW and PG, = 125 MW %3D (d) PG, = 100 MW and PG, = 150 MW

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus (slack bus), and bus 2 is load bus. Using the Gauss-Seidel method, determine the value of the voltage at the load bus 2 and perform two iteration. Moreover determine the complex power flow at bus 1 and also active and reactive power in transmission line. The line impedance on a base of 100 MVA. Use an initial estimate of V,º = 1+ j(0) . S1 Z12 = 0.02 + j0.04 2 S2 = 280 MW +j60 Mvar
Q4(b) The equivalent circuit of a single phase short transmission line is shown in Figure Q4(b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4(b) for the lagging power factor at load point (Vn). ii) Summarize, what if the load change from low value to high value shown in Figure Q4(b). R XL el Vs Vn Figure Q4(b) Load
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
How will you ensure minimum cost for the generation of required power for a given load? You may neglect transmission line losses. Support with mathematical formulations
Discuss why a. Complex power in an AC circuit is more than the DC resistance. b. Receiving end voltage of an unloaded long line may be more than sending end voltage. c. Inductance of the three phase of a transmission line are generally not equal. d. It is necessary to use the geometric means radius in the formula for the inductance calculation whereas the formula for the capacitance calculation uses the actual radius.
In nominal-T method of medium transmission line what is the assumption about the capacitance
The equivalent circuit of a single phase short transmission line is shown in Figure Q4 (b). Here, the total line resistance and inductance are shown as lumped instead of being distributed. i) Sketch the phasor diagram and assess with by labeling the details for the A.C. series circuit shown in Figure Q4 (b) for the lagging power factor at load point (Vn). ii) Summarize, the impact of voltage regulation and efficiency, if the line resistance and line increases are doubled Figure Q4(b). R XL Vs Vn Figure Q4(b) Load
Complete the sentence The power factor must be close to ……………. To insure that losses in the transmission lines will be reduced
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
3. Which one of the following method uses weak coupling between reactive power and voltage angle?. A. Newton - Raphson Method B. Decoupled Method C. Gauss-Seidal Method
Problem 4. A 220-kV, three-phase transmission line has a per phase series impedance z= 0.005 + O/km and a per phase shunt admittance y = j3.5x10 S/km. the line is 80 km long. The transmission line is delivering 200 MVA, 0.8 power factor lagging at 230 kV. Using the nominal pi model. d) Determine the voltage regulation and the transmission efficiency.
please solve for nodal stress method. (if it is possible to apply supernodes)