4.8 An ideal chopper is operating at a frequency of 500 Hz from a 60 V battery input. It is supplying a load having 3 2 resistance and 9 mH inductance. Assuming the load is shunted by a perfect commutating diode and assuming battery is loss less, what is the mean load current at an on/off ratio of 1/1? (a) 10 A (b) 15 A (c) 20 A d.c.(1-K)

4.8 An ideal chopper is operating at a frequency of 500 Hz from a 60 V battery input. It is supplying a load having 3 2 resistance and 9 mH inductance. Assuming the load is shunted by a perfect commutating diode and assuming battery is loss less, what is the mean load current at an on/off ratio of 1/1? (a) 10 A (b) 15 A (c) 20 A d.c.(1-K)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 20-V-rms 60-Hz ac source is in series with an ideal diode and a 100-Ω resistance. Determine the peak current and PIV for the diode.
Determine the voltage across the diode in the figure below, using the complete diode model with: r'd = 10-? and r'R = 100-M?a. The value of the forward current. (in Amperes)b. The value of the forward voltage. c. The value of the voltage across the diode.
A sinusoidal voltage of peak value 50 V is applied to a diode as shown in the figure. Sketch the waveform of voltage Vo treating the diode as an ideal one.
An ac voltage of peak value 20v is connected in series with a silicon diode and load resistance of 5002. if the forward resistance of diode is 102 find: i- Peak current through diode. ii- Peak output voltage. ii- What will be these values if the diode is assumed to be ideal (Vdiode =0)?
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
p4. A biased clamper is connected to a rectangular AC input with 20V on the positive half cycle and -10V on the negative half cycle. The orientation of the Si diode is the same with Vo while the 5V biasing voltage is in opposite connection. The value of R is 100K ohms while the capacitor is 1 microFarad. In P4, what is the voltage across the capacitor? a. 34.3V b. 14.7V c. 24.3V d. 20.7V
Q4- Give a possible applications for a Zener diode ?
In the circuit shown in the figure; A) When RL = 5Kohm and capacitor C is switched on, draw VA and V0 in scale according to input voltage Vs. NOTE = diodes are ideal
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
Using ideal diodes (voltage drop across ideal diodes is zero) and resistors, construct a circuit that results in the following output vs. input voltage characteristics.
4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂