4.A. What type of seal system is constructed of a hard brittle material and is often used in a pump to seal between the pump and the motor? A. Steel B. Ceramic C. Glass

Q: In Lin the center position port A and B are connected to tank port and pump port is blocked.

A: Hydraulics is a part in which the fluid power is used for various applications. The fluid pressures…

Q: introduction about Control of Pneumatic Cylinder with AND and OR Functions

A: Pneumatic cylinders (also known as air cylinders) are mechanical devices that generate force in a…

Q: Type of Mechanism

A: As given in question we have to match the following mechanism; hence; (P) SCOTT (Q) Geneva mechanism…

Q: Write in detail about working of any one pneumatic application in manufacturing area with neat…

A: Pneumatic robotic  arms Robotic arms are useful for activities that are tedious or may be too risky…

Q: Is a hook good on a compression spring launcher trigger mechanism

A: Given Spring triggered mechanism To find Verify hook is good for spring triggered mechanism

Q: Explain the operation of Buchholz relay.

A: Buchholz relay Buchholz relay in a transformer is an oil tub containing the connecting line from the…

Q: Which of these equipment that does not belong to the class of equipment listed below Pneumatic tired…

A: Answer is b).Bitumen distributor.

Q: Explain and give details about Run to failure strategy under plant maintenance

A: The Run to failure strategy is the simplest maintenance strategy. In this strategy assets are…

Q: What's the similarity,  advantage and disadvantage between hydraulic system and pneumatic system?

A:

Q: swejbeip eu Me diagrams TIS load on overhang point of contra-fle

A:

Q: 16. When a pneumatic solenoid fails, the failure is normally due to a O A. weak pilot. O B. bad…

A: When seal is damaged, the valve does not shut off properly. after a close inspection damaged…

Q: 2. Technician A says that load-carrying ball joints should always have some play in them. Techni-…

A: The ball joints basically serve as the pivot point between the tyre and the suspension in an…

Q: ring a load of/ 10 sunports are at th

A:

Q: le for the key to fail in an overload condition rather than more costly

A: While designing a shaft it is always use to design key weekend . Because in case of failure less…

Q: Select the main steps in the life cycle of of a pneumatic system.

A: Pneumatic System. A pneumatic system is a compressed air system that transmits energy and…

Q: a. Explain resonant earthing system with diagram b. How will you give Combined Leakage and Overload…

A: (a) Resonant earthing system : Resonant earthing is a sure uncommon sort of high impedance earthing…

Q: 7 - Which is not a type of freight car? A) safe

A: Option (e) is correct. high edged is not a type of freight car.

Q: The capacity control for a screw compressor is accomplished with cylinder unloading true or false

A: A rotary compressor makes use of a rotary type displacement mechanism. These compressors are usually…

Q: Name and describe the two principal types of conveyor holdbacks

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: What areas within a vane pump or motor are the most susceptible to contamination-induced clearance…

A: Vane Pump :  A vane pump is a type of positive displacement pump that delivers a constant flow rate…

Q: B2. Explain the function of Thermocouple with neat diagram and mention its advantages.

A: The thermocouple is a thermoelectric device that is used for temperature sensing. It is based on See…

Q: write discussion about to determination of the capacity of a belt conveyor.

A:

Q: Materials that can be used as housing for the Wedge belt Drive

A: The materials used are -

Q: Write in detail about working of any one pneumatic industrial application with neat diagram.

A: Pneumatics is the technique which utilizes high pressure gas in order to obtain a mechanical…

Q: ist two main types of robot joints ar

A: The moveable components of the robot that result in relative motions between adjacent connections…

Q: What is Belt-conveyor system?

A: The belt conveyor system is essential in a material handling industry. It is used to transport bulk…

Q: .1. A chain-drive system can be aligned easier than a belt-drive system since the chain-drive system…

A: A chain-drive system an be aligned easier than a belt-drive system since the chain-drive system A.…

Q: 3. With a neat sketch explain the Analysis of simple hydraulic Jack.

A:

Q: /5 --- A computer cannot "boot" if it does not have the

A: An operating system is the system software that handles the software and hardware resources and…

Q: Derive an expression for the height of propell governor

A: Governors are the most effective way to manage or regulate an engine's speed based on variable…

Q: Industrial issues that can be solved by conveyor belt water cleaning machine.

A: Belt cleaners with superior performance keep belts clean, reducing carryback and improving belt…

Q: Importance of Dual side working system using scotch yoke mechan

A:

Q: How are mechanical cooling system clutch fans often engaged? Select one: a. A ratcheting mechanism…

A: Whereas numerous unused vehicles utilize electric cooling fans, numerous more seasoned vehicles…

Q: Define relay

A: Relay is also called an electromagnetic switch. It uses low amperage electrical circuit used to…

Q: B2. Explain the function of Thermocouple with neat diagram and mention its advantages. [-

A: A Thermocouple may be a sensor utilized to degree temperature. Thermocouples comprise of two wire…

Q: 19.a. A machine has a coupling that fails once every year and a half. What type of PM task can be…

A: Preventive maintenance - It is routine maintenance of equipment in order to keep them running and to…

Q: out and Tagout

A: given: Explain the difference between Lockout and Tagout

Q: Forcesin Cable BA d ch-7 lom 2om

A: Given: W=100 kg

Q: 11. Fluid sealing in a dashpot is achieved using

A: GIVEN DATA A MCQ GIVEN ASKING WHICH SEALING USED IN FLUID DASHPOT SYSTEM

Q: Differentiate between a fast and loose pulley.

A: Difference between fast pulley and loose pulley is given below.

Q: A So Find tension in AC and BC Hoola

A:

Q: What is the problem arise when design a pneumatics system with more than 1 cylinder

A:

Q: Transmission angle is the angle between and link of a four bar mechanism

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.