4/106 In the special position shown for the log hoist booms AF and EG are at right angles to one an other and AF is perpendicular to AB. If the hoist is handling a log weighing 4800 lb, compute the forces supported by the pins at A and D in this one position due to the weight of the log. E 8° 10 A 45° B 12 24

4/106 In the special position shown for the log hoist booms AF and EG are at right angles to one an other and AF is perpendicular to AB. If the hoist is handling a log weighing 4800 lb, compute the forces supported by the pins at A and D in this one position due to the weight of the log. E 8° 10 A 45° B 12 24

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

Pulley A delivers a steady torque of 1100 lb-in. To a pump through its shaft at C. The tension in the lower side of the belt is 165 lb. The driving motor weighs 200 lb and rotates clockwise. Determine the bearing reaction force at O. A 9" B 30° 37 8" 150 lb - 5"-- 5"-
The round stepped shaft (diameters d and D) shown below is a design for an exoplanet rover wheel axle. Assuming the wheel is stuck, a torque from the motor is transmitted to the axle but it is not rotating. The reaction of the weight of the rover on the ground and the torque the wheel applies to the ground are represented by the force F acting in the center of the wheel hub (not shown) at point C. There is a sharp fillet at B with radius r shown below. Bearings are shown at point A and next to point B. You may assume the bearing at B resists the bending moment caused by the force F and acts like a fixed reaction. В A L2 L1 T L3 - ØD Ød R. r F SUBMIT ANSWERS HERE: Paramete Parameter Value Value SUT (tension) 400 MPa | L1 400 mm Suc (Compression) 600 Мра L2 200 mm Sy 380 MPа L3 100 mm 600 N-m ø d 40 mm F 0.2 kN ø D 55 mm R. r 8 mm
The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
Calculate all forces acting on the bar AB described in Prob. 5.1.
Current Attempt in Progress In the special position shown for the log hoist, booms AF and EG are at right angles to one another and AF is perpendicular to AB. If the hoist is handling a log weighing 4380 lb, compute the magnitudes of the forces supported by the pins at A and D in this one position due to the weight of the log. 50° A = Answers: i D= i 15" A 13' 26" B eTextbook and Media E C lb lb R 10" 3' -"( 14' G
A wheel radius 0.4meter has mass 3kg se figure. Center of wheel goes a rope to point A, the wheel has contact with the edge of the table in point B. An mass of 2kg is hanging from the edge of wheel in point C. Find the tention force for the rope attached in the centrum of the wheel.and point A
is formed in a quar- C6-67 The lever shown in Fig. ter circular arc of radius 20 in. Plot A and B, the magnitude of the pin force at A and the force on the smooth support B, as a function of e (0° s 0s 85°), the angle at which the support is located. 125 lb B A 20 in.
Frames & Machines The truck shown is used to deliver food to aircraft. The elevated unit weighs 2000 Ib with center of gravity at G. 1- Derive the expression for the force in the hydraulic cylinder AB as a function of 0 (the angle that member FD makes with the horizontal). 2- Plot the force over the range 0° < 0 < 45° and discuss your observations. Note: | would suggest that you first solve the problem based on the position (angle) shown. You will need to determine the length of members FD and FB before solving the problem for arbitrary 0. Note that the location of the roller at D and hence the force reactions will change as 0 varies. 40" 17" 57" C 54" E 54" H AB
For the same question, the Driving force (pressing force) of the Nut will be measured with the Torque wrench. While tightening the nut, the contact surface rubs against the fixed surfaces. Accordingly, how much MOMENT do we need to read from the Torque wrench in order to create a force of Fçak=1101 kgf? (Given: Screw pitch M30, Root diameter d1=25.8 mm) Outer diameter of the friction surface under the nut D42 mmFriction coefficient μ=0.6
solve with free body diagram
4/6- Frames & Machines / Charpente et Mécanisme Sample Problem / Exemple (4-6) The frame supports the 400-kg load in the manner shown. Neglect the weights of the members compared with the forces induced by the load and compute the horizontal and vertical components of all forces acting on each of the members. ↑ 1.5 m 0.5 m Тв 1.5 m 1.5 m ✓ C A 3 m -2 m E F 0.5 m 400 kg La structure supporte une charge de 400 kg de la façon représentée. Négligez les poids des barres par rapport aux forces développées par la charge et calculez les composantes horizontales et verticales de toutes les forces qui agissent sur chacune des barres.
Practice Problem 3: Solve for the resultant force. F = 500 lb 30 45° F= 800 lb