446 CHAPTER 17 17-102. The slender, 200-kg beam is suspended by a cable at its end as shown. If a man pushes on its other end with a horizontal force of 30 N, determine the initial acceleration of its mass center G, the beam's angular acceleration, the tension in the cable AB, and the initial acceleration of the end A. 30 N- PLANAR KINETICS OF A RIGID 2 m B Prob. 17-102 4 m 17-103, The spool has a mass of 75

446 CHAPTER 17 17-102. The slender, 200-kg beam is suspended by a cable at its end as shown. If a man pushes on its other end with a horizontal force of 30 N, determine the initial acceleration of its mass center G, the beam's angular acceleration, the tension in the cable AB, and the initial acceleration of the end A. 30 N- PLANAR KINETICS OF A RIGID 2 m B Prob. 17-102 4 m 17-103, The spool has a mass of 75

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A cord is wrapped around a homogeneous disk of radius r = 0.5 m and mass m = 14. 25 kg. If the cord is pulled upward with a force T of magnitude 171 N, determine a. the acceleration of the center of the disk, b. the angular acceleration of the disk, c. the acceleration of the cord. T 0.5 m Go A Draw the Free Body Diagram.
(A) A uniform rod 4 m long slender rod AB of mass 40.775 kg is rigidly connected to the center of a think disk of mass 30 kg as shown in the figure. The diameter of the disk is 2 m. At the instant shown the counterclockwise angular velocity of the disk is 10 rad/sec. • (a) Find the resultant acceleration of the center of the rod AB and • (b) determine the support reactions at A. Im B 200 kg
ANSWER= 3.621790, -9.99745 19 (aB)₂ = (aB)y 0 -12.49 A Two identical uniform slender rods with length 2.2 m and mass 3 kg are pin-connected at A. One of the rods is also pin-connected at its other end to fixed point O. If the system is released from rest in the position shown in the figure, find the initial acceleration of point Bat the end of the rightmost rod. The angle is 21°. For the purposes of reporting the acceleration, consider + to the right and +y upward. 3.8999 B x0% → x 0% m/s² m/s²
4 -(Kinetics of Curvilinear Motion) Tow weights W, and W2 of 8KN and 5KN are attached at the ends of a flexible cable. The cable passes over a pulley of 100 cm diameter. The weight of the pulley is 600N with a radius of gyration of 50cm about its axis of rotation. Find the torque which must be applied to the pulley to raise the 8KN weight with an acceleration 1.5 m/s?. Neglect friction in the pulley bearing. 50 cm 600N T 8kN 5kN W,
Given: A uniform slender rod is at rest upon a frictionless horizontal surface when a force (F) is applied in the direction shown. Assume that the rod has mass m and length L. A L Horizontal Plane Given that F = 74lb, L = 7.1 ft, mg = 4.6lb, and 0 = 73deg What is the component of acceleration of the mass at point G in the i direction? Answer: Check What is the component of acceleration of the mass at point G in the j direction? Answer: Check What is the component of angular acceleration of the mass in the k direction? (remember your signs) Answer: Check
The uniform slender rod, witha mass of 9.6 kg and a length ofE = 0.76 m, is fixed to a light vertical shaft at 0. The shaft can rotate freely in the stationary socket on the floor. A constant moment of M 11.8 N m is applied to the shaft, as indicated. What is the magnitude of the angular acceleration (in rad/s) of the rod? The rod moves in a horizontal plane.
A single cylinder horizontal engine runs at 120 r.p.m. The length of stroke is 400 mm. The mass of the revolving parts assumed concentrated at the crank pin is 100 kg and mass of the reciprocating parts is 150 kg. Determine the magnitude of the balancing mass required to be placed opposite to the crank at a radius of 150mm which is equivalent to all the revolving and 2/3rd of the reciprocat- ing masses. If the crank turns 30° from the inner dead centre, find the magnitude of the unbalanced force due to the balancing mass.
The 100 kg cylinder has an angular velocity of 30 rad/s If the coefficient of kinetic friction is 0.2. The axle through the cylinder is connected to 2 symmetrical links (only AB is shown) Assume that the links are massless. 11 20⁰ 500 mm Mass moment of inertia (kg.m²) FAB (N) Normal force with the ground N (N) co = 30 rad/s Choose C 2 D B 200 mm
A locomotive consists of multi cylinder reciprocating engine running at a speed of 8 r.p.s having a stroke length of 25cm, which carries a mass of reciprocating part whose magnitude is 8kgs with a revolving part of 4kgs rotating at 17cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 560 from top dead centre to bottom dead centre. 1. Maximum primary unbalanced force of reciprocating mass in newtons 2. Balancing mass required at a radius of 35cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 72cm between the two cylinders in (N-m) 5.…
A locomotive consists of multi cylinder reciprocating engine running at a speed of 8 r.p.s having a stroke length of 29cm, which carries a mass of reciprocating part whose magnitude is 11kgs with a revolving part of 5kgs rotating at 17cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 500 from top dead centre to bottom dead centre. solve 4 and 5 1. Maximum primary unbalanced force of reciprocating mass in newtons 2. Balancing mass required at a radius of 41cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 76cm between the two cylinders in (N-m) 5. Magnitude…
Help me please
R - m 130° A hollow wheel of mass given by m 50 kg rolls down an incline of 30° without slipping. The inner radius of the wheel is given by R = 50 mm and its thickness is given by d = 5 mm. Gravity acts down. (a) Show that the moment of inertia of the wheel is given by Ī = 138 125 kg mm². (b) Show that the linear acceleration of the wheel's centre of gravity ā is related to the angular acceleration of the wheel a via a (55 mm)a. = (c) Analyse an appropriate free-body diagram to determine the linear acceleration of the wheel's centre of gravity ā.