* Z 4.5G+ İl.HW2.pdf"STATICS"HOME WORK (2)Q1: The machine part of negligible weight is supported by a pin at A and a roller at Casshown in Fig. 1. Determine the magnitudes of the forces acting on the part at A and C.Q2: The tool shown in Fig.2 is used in a gluing operation to press a thin laminate to a thickersubstrate. If the wheels at points A and B both have 2 in diameter and have frictionlessbearings, and a 20 lb vertical force to the handle of the tool, determine the forces applied tothe top of the laminate and the bottom of the substrate.Q3: For Fig.3, determine the tension in cable ABD and the reaction at support C.Q4: The 2-Mg uniform pole in Fig.4 is supported by a ball-and -socket joint and two cables.Determine the tension in cables AC and BD.termine the horizontal and vertical components of reaction at the pin A and thereacu. of the smooth collar B on the rod shown in Fig.5.2010 in-124 LN-mlaminate200230250300-substrateNTE3ENDimeraioea in mmFig.1Fig.240LN125 mm450 b300 b175 mmft--225 mm -75 mm150 NFig.3Fig.5Fig.4

As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Answered: 450 b 300 b Fig.5

Engineering

Mechanical Engineering

450 b 300 b Fig.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal. Response
4. A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the wall. A 700N man stand 6m up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping. Draw the FBD
Open with Google Docs The homogeneous semicylinder rests on a horizontal surface and is subjected to the force P applied to a cord firmly attached to its periphery. The force P is slowly increased and kept normal to the flat surface of the semicylinder. If slipping is observed just as 0 reaches 40°, determine the coefficient of static fric- tion u, and the value of P when slipping occurs. B 3.
Q2): Body A is weight 100 N and tied to a rigid wall using a steel cable and it is located on body B of weight 300 N which rest on a rough surface (coefficient of fraction is 0,3). If the fraction coefficient between body A and B is equal to 0.25 and the pulling force P= 600 N. calculate the tension force of the steel cable. A 530 37 B TTTTTT
An engineer trying to determine whether her crane will tip over when attempting to lift a 13K load. Her crane has a 15K chassis and 35K counterweight. Assume all other parts of the crane have negligible weight. Answer all questions relative to the rotation point. How much torque is caused by the load? How much torque is caused by the chassis? How much torque is caused by the counterweight? What is the normal force on the rear (right) outriggers? What is the normal force on the front (left) outriggers? *each box in picture = 5 ft
3. The figure shows a 100.kg box suspended from the extreme side of the horizontal truss. Assume that the truss's weight is negligible; what is the tension (N) in the cord supporting the truss. Angle is 38 degrees from the horizontal side of the truss IS CORD truss 4. A 3,000. kg truck is towed up along a hill with a cord whose functional strength is 10,000 N. The hill is inclined at 15 degree from the horizontal. Find the maximum acceleration of the truck in m/s^2.
Answer in this format. Sketch: Given: Required: Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) An electrical worker stands in the bucket that hangs from a pin at end D of the boom of the cherry picker in Fig. 1. The worker and bucket together weigh a total of 300 lb. Between A and C the boom weighs 1.1 Įb/in., and between C and D it weighs 0.8 Jb/in. Assume that AC and CD are uniform beams. Determine the normal force, the transverse shear force, and the bending moment that act at cross section E, midway between A and B. В Eaxial Eshear Emoment Ib Ib Ib Ib in 50" 40" D 10"10 INDICATE WHETHER POSITIVE OR NEGATIVE |20° Bucket 60° Fig. 1 (a) “Bucket truck."
2. Problem 2: A flat plate, shown below, with a fillet radius of 0.1875 in. is subjected to an axial tension force of 1000 lbs on the right side. The plate is fixed on the left side. The dimension of the plate is given in the figure below and the thickness of the plate is 0.25 in. Note that all dimensions are in inches. It will be faster to model this in Creo Parametric Or Solid Works and then save it as a step file. Material is Structural Steel, same used in the tutorial (RECTANGULAR PLATE WITH CIRCULAR HOLE SUBJECTED TO TENSILE LOADING). 22500 2.25 4.0000 4.00 H PRT_CSYS DEF 0.1875 VPRT CSYS DEF R. 1875 f*f* R₁ 11 10.00 10.0000 3.0000 0.7500 3.0000 -0.7500 1.5000 $ 1.50
4. A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the wall. A 700N man stand 6m up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping.
Question 1 a) Figure Q1a shows a bracket that can roll and move horizontally along a beam. A 1600 N force at 15° relative to the horizontal axis acts at A. Determine the force P at 25° relative to vertical axis necessary to keep the bracket static; (i) (ii) Calculate the downward resultant force acting vertically at A. Assume coplanar forces. 150 1600 N 250 P Figure Q1a b) If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the maximum allowable stress in the pipe is 7.5 x 10º N/m², calculate the minimum wall thickness required for the pipe. Give your answer in millimetres (mm) to 2 decimal places. c) A wire with a Young's Modulus, E, of 8.5 x 106 N/m² and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m² to 2 decimal places.
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
The figure shows a mechanism that raises packages in a transfer mechanism. A 500-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 400 rpm CW. At the position shown the crank OA is vertical and the output link O4B is horizontal. we need to determine the torque required from the motor at the crank 02A and the force in member AB The weights of the links are negligible. 30mm 450mm 500N 220 mm B 374 mm 374 mm The angular velocity of the link O,BD in rad/s is = The magnitude of the velocity of point D in m/s is =