5-84 Hot exhaust gases of an internal combustion engine are to be used to produce saturated water vapor at 2 MPa pressure. The exhaust gases enter the heat exchanger at 400°C at a rate of 32 kg/min while water enters at 15°C. The heat exchanger is not well insulated, and it is estimated that 10 percent of heat given up by the exhaust gases is lost to the surroundings. If the mass flow rate of the exhaust gases is 15 times that of the water, determine (a) the temperature of the exhaust gases at the heat exchanger exit and (b) the rate of heat transfer to the water. Use the constant specific heat prop- erties of air for the exhaust gases. Q Exhaust gases 400°C 2 MPa sat. vap. FIGURE P5-84 Heat exchanger Water 15°C

5-84 Hot exhaust gases of an internal combustion engine are to be used to produce saturated water vapor at 2 MPa pressure. The exhaust gases enter the heat exchanger at 400°C at a rate of 32 kg/min while water enters at 15°C. The heat exchanger is not well insulated, and it is estimated that 10 percent of heat given up by the exhaust gases is lost to the surroundings. If the mass flow rate of the exhaust gases is 15 times that of the water, determine (a) the temperature of the exhaust gases at the heat exchanger exit and (b) the rate of heat transfer to the water. Use the constant specific heat prop- erties of air for the exhaust gases. Q Exhaust gases 400°C 2 MPa sat. vap. FIGURE P5-84 Heat exchanger Water 15°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ammonia and air pass through the heat exchanger. While the ammonia is entering as asuperheated vapor at 16 bar pressure and 60C temperature it is leaving as a saturated liquid at thesame pressure but unknown temperature. The ammonia mass flow rate is 400 kg/hour.Air is flowing backward and is heated from 17C to 42C at the constant pressure of 2 bars.NOTE: Find air properties from https://www.peacesoftware.de/einigewerte/luft_e.html a. Draw the ammonia T-v diagram showing the stages, pressures, and temperatures b. How much heat is transferred from ammonia to air assuming no heat transfer to thesurroundings? c.Determine air mass flow rate Please show all steps in solution thanks
A heat exchanger was installed purposely to cool 0.50 kg of gas per second. Molecular weight is 28 and k=1.32. The gas is cooled from 150⁰C to 80⁰C. Water is available at the rate of 0.30 kg/s and at a temperature of 12⁰C. Calculate the exit temperature of the water.
A fruit juice is being heated in an indirect heat exchanger using steam as a heating medium. The product fl ows through the heat exchanger at a rate of 1500 kg/h and the inlet temperature is 20C. Determine the quantity of steam required to heat the product to 100C when only latent heat of vaporization (2200 kJ/kg) is used for heating. The specifi c heat of the product is 4 kJ/(kg C).
Steam with 90% quality is being used to heat a 40% total solids tomato puree asit flows through a steaming injection heater at a rate of 410 kg/hr. The steam isgenerated at 130oC and is flowing to the heater at a rate 60kg/hr. If the specificheat of the product is 3.5 kJ/kg-K, determine the temperature of the product leavingthe heater when the initial temperature is 50°C. Determine the total solids contentof the product after heating. Assume the specific heat of the heated puree is 3.8 kJ/kg- °C.
The air considered as the ideal gas flows through the compressor and heat exchanger at a volumetric flow rate of 26.91 m3 / min as shown in the figure. At the same time, a stream of liquid water passes through the heat exchanger. The information given in the figure is for continuous flow. Considering the compressor and heat exchanger as adiabatic and ignoring kinetic and potential energy changes, a) the power requirement of the compressor (kW) and the mass flow rate of the cooling water (kg / h),b) Calculate the entropy generation (kW / K) per unit time for the compressor and heat exchanger.
Steam at 1.6 MPa and 350°C enters a steam turbine at a flow rate of 16 kg/s. Thesteam leaves the turbine as a saturated vapor at 30°C. The turbine delivers 9 MW ofpower. A schematic of the turbine and its operating conditions are given in theFigure below. Determine the heat transfer rate from this turbine.
A steam at 169.06 kPa of 90% quality is used to concentrate tomato juice to puree.The specific heats of tomato juice before and after evaporation are 3.89 and 3.45kJ/kg-K. The specific heat of the solid content of tomato juice is 2.67 kJ/kg-K andthe mass flow rate of juice at the feeding section is 2.1 kg/s. What will be the exittemperature of the juice? Assume that the steam after heat exchange exits aspure liquid.
The stream of air and gasoline vapour,in the ratio of 14:1 by mass, enters a gasoline engine at a temperature of 30C and leaves as combustion products at a temperature of 790C. The engine has a specific fuel consumption of 0.3kg/kWh.The net heat transfer rate from the fuel-air stream to the jacket cooling water and to the surroundings is 35kW.The shaft power delivered by the engine is 26kW.Compute the increase in specific enthalpy of the fuel-air stream, assuming the changes in kinetic and potential energy to be negligible.
converted to P6-31 In a desuperheater, superheated steam is saturated steam by spraying liquid water into the steam. Using data on the figure, calculate the mass flow rate of liquid water. Superheated steam m₁ = 0.3 kg/s T₁ = 250°C P₁ = 2 MPa + 1 (2) Liquid water T₂ = 30°C 3 11:00 Saturated vapor
Combustion gases enter the nozzle of a jet engine at 3.8 bar and 820 o C. Thenozzle is well insulated and the gases expand down to an exit pressure of 1.1 bar.Determine the temperature and the velocity of the gases at exit from the nozzleassuming the velocity at inlet is negligible. For the combustion gases takec p = 1.15 KJ/Kg. K and the ratio of specific heats = 1.32
Water inter a condenser at a mass flow rate of (2.5 kg/s) and (21 kPa and 65 C), and exit with (h= 251.5 kJ/kg). Find: a) The mass flow rate of water flow at the exit section b) the rate of heat removed from the water in the condenser. From table: at T1-60-C & P1-21 kPa -hl=2423x10 J/kg
Hot air at 400°C and 150 kPa is to be used to produce saturated steam at 200°C in an insulated, non-mixing heat exchanger. Water enters the heat exchanger at 20°C while the air leaves at 350°C. The mass flow rate of air is 0.8 kg/s, pressure drops are negligible, and specific heats for air are evaluated at the average air temperature.What is the mass flow rate of water, in kg/s. Report your answer to four decimal places using rounding.