5) Link AB, of width b-2 in. and thickness t-0.25 in., is used to support the end of a horizontal beam. If the average normal stress in the 1ink is 20 ksi and that the average shearing stress in each of the two pins is 12 ksi determine (a) the diameter d of the pins (b) the average bearing stress in the link Answer: Answer:

5) Link AB, of width b-2 in. and thickness t-0.25 in., is used to support the end of a horizontal beam. If the average normal stress in the 1ink is 20 ksi and that the average shearing stress in each of the two pins is 12 ksi determine (a) the diameter d of the pins (b) the average bearing stress in the link Answer: Answer:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The maximum tension in the wèr link of a Porter governor is 580 N and the maximum stress in the link is 30 N/mm?. If the link is of circular cross-section, determine its diameter.
1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view 160 mm 13 D CB Top view 18 mm 120 mm C D Side view 6 mm
A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
6. In the steel structure shown, a 6mm diameter pin is used at C and 10mm diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Note that link BD is not reinforced around the pin holes. a. Determine the largest load P that can be applied at A maximizing the shearing capacity of the pin at C. b. Determine the largest load P that can be applied at A maximizing the shearing capacity of the pins at B and D. c. Determine the largest load P that can be applied at A maximizing the axial capacity of link BD. Front view -X 15 mm mm B Side view -120 mm Top view
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
2. Member AB shown in the figure supports a 5 N/mm uniformly distributed load and 4kN concentrated load as shown in the figure. Determine the position x of these loads so that the average tensile stress in the tie rod AC is equal to 90% of the compressive stress at the smooth support B. The rod has a diameter of 19 mm and the contact area at is 700mm². (Hint: quadratic formula) B A X 5 N/mm 4 kN 300mm B
ABDE rigid rod with single action rivet from point A, point B Connected with BC rod. B and C points of the rod are fence effect rivets. The maximum shear stress that the rivets can bear is 550 MPa, that of the BC bar Since the maximum tensile stress is 440 Mpa, the safety factor FS = 2; 1 ) Calculate the diameter of rivets A and B 2 ) Calculate the diameter of the BC rod
A torsion member is fabricated from two concentric thin tubes. At the ends, the tubes are welded to rigid discs so that both the tubes are twisted as a unit. The radius of the outer tube is 2r and that of the inner tube is r. If the shear stresses developed in the outer tube is 'T', then the shear stress in the inner tube will be (a) (b) 0.25t (c) 0.75t (d) 0.5t
Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.8-in. diameter is used at each connection, determine the maximum value of the average normal stress (a) in link AB, (b) in link BC
A gusset plate is connected to the flange of column with the help of fillet weld on both sides as shown in the figure. The direct shear stress and bending tensile stress are 70 MPa and 130 MPa respectively. Find the equivalent stress (in GPa). Gusset plate I-section flange
A plate with width of 300mm and thickness of 20mm is to be connected between two plates 12mm thick with same width by 4-25mm diameter rivets a shown. The rivet holes have a diameter 2mm larger than the rivet diameter. The plate is A36 steel with yield strength Fy=248 Mpa and Fu-400MPa. The rivets have nominal shear stress capacity of 165MPa. O 803 O 1490 • Determine maximum load (P1) that can be applied without exceeding design tensile stress in plates (consider yielding and rupture of plates ONLY) in KN O 1180 O 1340 ο ο ο ο ο P3 O 1968 O 590 O 670 O 893 O 707 OO 150 O 1180 P1 P2
A plate with width of 300 millimeters and thickness of 20 milimeters is to be connected to two plates of the same width with half the thickness by 25 millimeters by 25 millimeters diameter rivets. The rivets holes have a diameter 2 millimeters larger than the rivetdiameter. The plate is A36 with yield strength F, = 248MP.. Allowable tensile stress on net area is 0.6Fy and allowable bearing stress of 1.3Fy. The rivets are A502, Grade 2, hot-driven rivets with allowable shear stress of 150MPA. 1. Detemine the maximum load that can be applied to the connection with consideration to the yielding failure in the plates. 2. Detemine the maximum load that can be applied to the connection with consideration to the fracture failure in the plates. 3. Detemine the maximum load that can be applied to the connection without exceeding the allowable shearing stress in the rivets. 4. Detemine the maximum load that can be applied to the connection without exceeding the allowable bearing stress between…