5. A water sample has been analyzed. Upon titration with EDTA, the following results were gathered. Volume of water sample: 10 mL Volume of CaCO3 solution in water sample: 5 mL Initial burette reading: 22.5 mL Final burette reading: 27.8 mL Determine the CaCO3 equivalent to 1 mL EDTA.

5. A water sample has been analyzed. Upon titration with EDTA, the following results were gathered. Volume of water sample: 10 mL Volume of CaCO3 solution in water sample: 5 mL Initial burette reading: 22.5 mL Final burette reading: 27.8 mL Determine the CaCO3 equivalent to 1 mL EDTA.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rectangular concrete beam (fixed at both ends) supports a dead load of 20 kN/m (including self…

A: Using NSCP 2015 f'c = 28 MPa If f'c ≤ 28 MPa , then β = 0.85 Also , a = β1 c where ; c = actual…

Q: For the following beam a. Draw the shear and moment diagra Determine b if the maximum allowa…

Q: a rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

Q: 30 kN C a 1m E b e 20 kN/m 8m HO- f 20,KN g 10 kN/m 6.0 2m 2m 2m ↓2m↓

Q: of a rectangular suppressed weir that will increase the depth

Q: A solid cube has an sg of 2.15 will float in salt water sg = 1.026 a. true b. false

Q: A centrifugal impeller has 17 radial blades in the impeller of 45 cm diameter. The tip diameter of…

A: Given:- The number of radial blades of the centrifugal impeller = 17 The diameter of the impeller is…

Q: 2 14 Edit & 12. What is the vertical effective stress at point, X in the soil profile given below? ▼…

A: Effective stress at point X is given by ; σ' = σ - U where ; σ' = Effective stress σ = Total stress…

Q: A rectangular canal is designed to carry 5 cu.m./s at a velocity of 1.8 m/s. For a most economical…

A: Q= 5 cu m/s Velocity = 1.8 m/s Cross sectional area = by= 5/1.8= 2.778 m2. for most economical…

Q: Names Fig 2 I T A 20 TR₁ 100 N/m 4M 4 G Answer 120N-m 三 R₂ Datet Time: Draw the shear and moment…

Q: the equivalent spring constant for below if the constant spring is 80 ?N/m 1110 k1 k2 m3 k3 k6 m1 k4…

A: k36=k25=180+180-1= 40N/m k4=80 N/m k23456= 40+80+40=160N/m k123456= 180+1160-1= 53.33N/m So…

Q: Water flows at the rate of 0.09 ml/s in an upward direction through a sand sample with a coefficient…

A: For bottom pressure = option a is correct = 364N/m2

Q: 6 kips 7 kips+ 3' 5' 5 kips 4' 4 kips

Q: Show

Q: Problem 9: For the state of a certain soil stress shown, maximum shear stress. Express your answer…

Q: 2) Find the support reactions, and draw M, N, V diagrams of the frame. P = (10+B) KN Q = 30 kN q =…

A: Given:- A frame is loaded with distributed load and point loads The magnitude of horizontal point…

Q: If the flow rate is 50 liters per second, what is the head loss in meters per kilometer on a 150 mm…

A: Asked: To compute the frictional head loss for flow through pipe. Given: Flow rate (Q) = 50 liters…

Q: 11-15. Analysis problem in an unbraced frame-using loads and moments obtained using the re-…

Q: Figure (101) the allowable bearing stress for the maternal under the supports at A and B 14MPa,…

A: Given:- The allowable bending stress at A and B = σallow = 1.4 MPa The magnitude of the uniform load…

Q: 2) Draw shear force and bending moment diagrams of the beam and find the maximum values of the shear…

A: shear force and bending moment : Shear force is defined as the algebraic sum of the vertical forces…

Q: 1. A triangular gate with a horizontal base 1.5 m long and an altitude of 2.1 m is inclined 42" from…

A: Force : A pressure is a power that could alternate the movement of an item. A pressure can reason an…

Q: F6-4. Determine the greatest load P that can be applied to the truss so that none of the members are…

Q: A diagram or a curve which is a used as a reference to picture the internal forces in a beam

Q: The beam shown is reinforced for tension at the bottom with 6-28 mm bars and at the top with 3-22 mm…

Q: Determine the allowable permissible Twisting moment, T (N-m) as shown in the figure: τst ≤ 83…

Q: - Add to Ú 14 Edit & Cr 12. What is the vertical effective stress at point, X in the soil profile…

A: Given data- unit weight of water γw=62.4 pcfunit weight of loose water γsat=115 pcfunit weight of…

Q: Determine a suitable W profile to limit the maximum stress σd=200 MPa

A: Given, The beam is simply supported having a total length of 9.9m Our aim is to select a lightest W…

Q: A block weighing 100 N is placed on an inclined plane of slope angle 30 degrees and is connected to…

Q: F6-1. Determine the force in each member of the truss. State if the members are in tension or…

Q: A 10m- propped cantilever beam, that is, the support at one-end is roller and the other end is…

Q: Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions…

A: Solution-The given values are ,f'c=21MPafy=420MPaTo DetermineThe tensile steel ratio

Q: Determine the equivalent amount pf money at the beginning of the second year if interest is 6% per…

A: Given principal amount = 10000 Interest rate =6% Compounded monthly

Q: Three pipes are connected in series. Pipe 1 has length of 850m and diameter of 600mm. Pipe 2 has…

Q: W ^^ 3m 6m 3m W 6m 6m

Q: 4. Determine the stresses in two segments of the bar shown. The hollow segment A has an O.D. 2 in.…

Q: x 240 Cool T A 400 KN Determine the FF. 12m Area = 0.0012m² | REA = 1. Bc 2. = 3. Stress BO 4.…

Q: The absolute pressure in a closed gas tank is 260 KPa. Compute the pressure head in meters of water.…

Q: A solid cube has an SG of 2.15 will float in fresh water a. true b. false

A: given- solid cube in fresh waterspecific gravity SG=2.15

Q: Determine the total deformation in inches if the flexural rigidity is equivalent to 5,000 kips. 6…

Q: Compute the mid-span deflection y = what is the max. deflection Yax mm

A: Given figure is a simply supported beam with uniformly distributed load acting at a distance of 1.5m…

Q: 20KN/m 4m R₁ Compute the following: (1-2) Vc = (5-6) V₂ = (9-10) Max. Moment occurs @ x= C 4m 10 KN…

Q: 2. (D³ - 7D + 6)y = 0

Q: Three pipes 1, 2, and 3 are connected in parallel and a fourth pipe is connected at B. The…

Q: L 0.6m 5m K-1 n-0.012 Q-18 m³/s Formulas: Rh 70- Q==AR 23S 112 n Determine the channel slope [A] use…

A: Asked: To compute the slope of the channel. Given: Manning's roughness coefficient (n) = 0.012…

Q: -3 m- WDL = 30 kN/m WLL 13 m 22 kN/m ती 3 m-

Q: If the height of a tower is 50 m, flying height of the aircraft above the base is 5000 m and the…

A: given- height of tower h=50 mflying height of aircraft H=5000 mimage of the top of the tower r=20 cm…

Q: For the following beam: (a) Find the reactions at supports. (b) Draw the Shear and moment diagram…

A: As there is no loading present, the reactions at A and B are zero. The shear force and bending…

Q: What is the maximum beam deflection? if W = 50KN/m, L = 3.7m, E = 52.5x10³, 1= 15.23x106 Choose the…

Q: 1) Find the support reactions, and draw M, N, X diagrams of the beam. P = (4+B) KN Q = 40 kN q = 60…

A: Asked: To draw the normal force (N), shear force (V) and bending moment (M) diagrams for the given…

Q: A rectangular beam 300 mm wide is to be designed for an ultimate moment of 750 kN·m with f’c = 28…

Concept explainers

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.

Question

Complete Answer, please. Thank you :)

5. A water sample has been analyzed. Upon titration with EDTA, the following results were gathered.
Volume of water sample:
10 mL
Volume of CaCO3 solution in water sample: 5 mL
Initial burette reading:
22.5 mL
Final burette reading:
27.8 mL
Determine the CaCO3 equivalent to 1 mL EDTA.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A water sample was tested for water hardness. A 50.00 mL sample, prepared andbuffered to pH 10, required 23.55 mL of 0.0250 M EDTA. A second 50.00 mL aliquot,prepared with NaOH, was titrated with 14.53 mL of the same EDTA solution.a. Calculate the total hardness of the water sample, express in ppm CaCO3b. Calculate the concentration of CaCO3in the sample in ppmc. Calculate the concentration of MgCO3in the sample in ppm
Calculation: Mmoist - Maryx 100% MC = : Mary Where: MC = moisture content in percent Mmoist = mass of original specimen Måry = mass of oven dry specimen Tabulated Data and Result Sample No. Mmoist (kg) Mdry (kg) MC 1 0.5 0.25 0.4 0.18 3 0.5 0.22 4 0.3 0.13
JQuestion a) Write down the chemical equations for the reactions that take place in the DO test. b) Discuss the environmental significance of DO. c) Why should DO fixation be performed in the field rather than in the laboratory? Data Sheet Volume of solution for titration = Samples Sample A Sample B (i) (ii) (iii) (i) (ii) (iii) Average Average Titration reading Start End (+0.05mL) (+0.05mL) mL Volume of Na2S2O3 (mL) Dissolved Oxygen (DO)(mg/L)
A water sample was examined and following observations were made: Species Concentration(milliequivalent) Calcium, Ca2 10 Magnesium, Mg2 Chloride, Cl 4 Sulphate, SO,- 11 Use above data, and choose the correct statement(s). Permanent hardness is caused by NO3 , S042, ions. Correct Option B Carbonate hardness of sample is 150 mg/l as Caco3 Your answer is IN-CORRECT Special method such as base-exchange process can be used to remove permanent hardness. Your option is Correct D Non-carbonate hardness in a 200 ml sample of given water is 150 mg as CaCo3- Correct Option
Ca+2 = 36.8mg/L Mg+2 = 2.9mg/L HCO3 = 98mg/L pH = 7.53 Temp = 9C Calculate the following: a. Hardness in units of mg/L as CaCO3 b. Ionic strength (be sure to include H++ and OH--) c. PCO2 in equilibrium with the sample d. Saturation index with respect to calcite (SIC) e. Saturation index with respect to dolomite (SID)
6-39 The following data were collected from a 10.16 mm-diameter test specimen of polyvinyl chloride (lo = 50.8 mm): Load (kN) Al (mm) 0.00000 1.334 0.1895 2.668 0.38 4.003 0.603 5.34 0.813 6.67 1.168 7.38 1.778 (maximum load) 7.12 2.388 6.316 3.048 (fracture) After fracture, the total length was 53.086 mm and the diameter was 9.982 mm. Plot the engineering stress strain curve and calculate (a) the 0.2% offset yield strength; (b) the tensile strength; (c) the modulus of elasticity; (d) the % elongation; (e) the % reduction in area; (f) the engineering stress at fracture; and (g) the modulus of resilience.
The Professor demonstrated the proper application of the procedure by analyzing a 50 mL sample of water from a local lake (Rivers Parkway) via titration with a standard solution of EDTA 0.0100 +0.0001 M standard. This sample consumed 5.00 mL to reach the Total Hardness (TH) end point; therefore, the TH of the lake was determined to be XX ± YY mg/L as CaCO,.
d) Calculate total hardness in ppm of a solution of both 55 mg/L Al2(SO4)3 and 45 mg/L Mg(NO3)2.
A commercial screen cloth of market grade is used to separate different fractions of 300 m³/hr of crystals obtained from crystallization via nucleation process in a cylindrical vessel of 3 m height and 9.25 m OD of thickness 3.6 cm. The properties of the slurry are: M, = 220 g/L; p = 1.26 g/mL; P = k, = 0.97 Mesh Sizes wt % -7 mesh +9 mesh 1.68 -9 mesh +12 mesh 2.31 -12 mesh +14 mesh 2.12 -14 mesh +18 mesh 13.90 -18 mesh +24 mesh 32.89 -24 mesh +40 mesh 45.78 -40 mesh Find: Kinetic equation b. Dominant particle c. What is the cumulative weight fraction at 700 microns? а.
6. The mineral analysis below was reported for a water sample. 6.0 Bicarbonate 120 as CaCO3 Ca2+ 50.0 SO?- 94.0 Mg* 20.0 pH 7.3 Na* 5.0 Note: All reported as "mg/L as the ion" unless stated otherwise. e. Draw a bar chart that includes all the ions listed above. f. What is the total hardness of the water in mg/L as CaCO3? g. What is the carbonate hardness of the water in mg/L as CaCO;? h. What is the non-carbonate hardness of the water in mg/L as CaCO3? How would you characterize this water (very soft, moderately hard, etc.)? Explain your i. answer.
A commercial screen cloth of market grade is used to separate different fractions of 300 m3/hr of crystals obtained from crystallization via nucleation process in a cylindrical vessel of 3 m height and 9.25 m OD of thickness 3.6 cm. The properties of the slurry are: MT = 220 g/L; ρ = 1.26 g/mL; φ = kv = 0.97 Mesh Sizes wt % -7 mesh +9 mesh 1.68 -9 mesh +12 mesh 2.31 -12 mesh +14 mesh 2.12 -14 mesh +18 mesh 13.90 -18 mesh +24 mesh 32.89 -24 mesh +40 mesh 45.78 -40 mesh Find:a. Kinetic equationb. Dominant particlec. What is the cumulative weight fraction at 700 microns?
Why are the sum of the anion concentrations and the sum of the cation concentrations are not identical in water analysis?