50 mm C 175 mm B. -225 mm -300 mm Bar ACB shown in the Figure is subjected to a uniform temperature increase of 35°C. Knowing that the diameters of AC is 50 mm and CD is 75 mm, the modulus of elasticity E is 6.0 GPa, and the thermal expansion coefficient is 100x10^(-6) * 21/°C. What is the displacement of point C

50 mm C 175 mm B. -225 mm -300 mm Bar ACB shown in the Figure is subjected to a uniform temperature increase of 35°C. Knowing that the diameters of AC is 50 mm and CD is 75 mm, the modulus of elasticity E is 6.0 GPa, and the thermal expansion coefficient is 100x10^(-6) * 21/°C. What is the displacement of point C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The column in the figure shown has a strain on its compressive edge equal to -0.003 and has a tensile strain of +0.00185 on its other edge. Detemine the nominal values of Pn and Mn that cause this strain distribution if f'c = 21 MPa, fy = 414 MPa. Draw the column interaction diagram. en 600 Pn mm 8 - 6 32mm 75 225 225 75 600
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE (express answer in MPa) if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm^2. Use 73.1 GPa and 23 x 10^-6/°C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively.
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE (express answer in MPa) if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm^2. Use 73.1 GPa and 23 x 10^-6 /°C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively.
In the figure, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 126°C. The 0.5-mm gap exists at 25°C. 0.56 mm 366 mm 255 mm Aluminum A = 2TTT mm² E = 75 GPa x = 23 x 10*/°C B Stainless Steel A = 8QQ mm² E = 190 GPa α = 17.3 x 10/°℃
An aluminum right-circular cylinder surrounds a steel cylinder as shown in Fig. 1-29. The axial compressive load of 200 kN is applied through the rigid cover plate shown. If the aluminum cylinder is originally 0.25 mm longer than the steel before any load is applied, find the normal stress in each when the temperature has dropped 20 K and the entire load is acting. For steel take E = 200 GPa, a = 12 × 10°°C, and for aluminum assume E = 70 GPa, a= 25 × 10ºC. 200 kN 500 mm 80 mm -85 mm- 141 mm
A brass wire of diameter d = 2.33 mm is stretched tightly between rigid supports so that the tensile force is T = 93 N (see figure). T The coefficient of thermal expansion for the wire is 19.5 x 106/°c, and the modulus of elasticity is E = 110 GPa. (a) What is the maximum permissible temperature drop (in °C) if the allowable shear stress in the wire is 60 MPa? (Enter the magnitude.) °C (b) At what temperature change (in °C) does the wire go slack? °C
The assembly shown in the figure consists of an aluminum tube AB and a steel rod BC. The rod is attached to the tube through the rigid collar at B and passes through the tube. The cross-sectional area of the rod is 75 mm2 and the cross-sectional area of the tube is 400 + UV in mm2, where UV is 99. A tensile load of 80 kN is applied to the rod. Take Est = 200 GPa for the steel rod, Eal = 70 GPa for the aluminum tube. Determine: (a) the displacement of end C with respect to end B (i.e., the elongation of the steel rod), (b) the displacement of end B with respect to the fixed end A (i.e., the shrink of the aluminum tube), (c) the displacement of the end C of the rod (i.e., (a) + (b)).
1. An axial force of 250 kN is applied to the assembly shown, made of cylindrical brass core surrounded by an aluminum shell. The axial force is applied through rigid end plates. a) Determine the normal stress in each of the metal components, given that Ebrass = 105 GPa and Ealum = 70 GPA. 100mm b) What is the axial deformation of the assembly? 200mm 200mm
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in each rod if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm2. Use 73.1 GPa and 23 x 10-6/ °C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively. 2 m 1 m D 1.1 m B. 1 m 1.25 m 1.5 m
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm
THERMAL STRESS 3. A rigid bar is supported by two copper rods and the gap between the aluminum rod and the bar is 1.50 mm. If the temperature for all materials is increased by 40 degrees Celsius, will the aluminum rod touch the rigid bar or not? Prove your answer. For each copper bar, A = 500 mm^2, E = 120 GPa and a = 16.8 um/(m C). For the aluminum bar, A = 400 mm^2, E = 70 GPa , and a = 23.1 um/(m C).
A steel rod having a cross-sectional area of 0.002 sq. m. and length of 1.5 m. is attached to unyielding supports. If the temperature falls 60 degrees Celsius, the modulus of elasticity of steel is 200 x 109 N/m2, and the coefficient of linear expansion is 11.5 x 10–6 per degree Celsius, finda. the deformation due to the temperature drop in mm, andb. the force exerted by the rods on the supports in kN..