6) Determine the following parameters according to power amplifier BJT circuit which is given below. 6.a) Calculate input power, output power and efficiency of the amplifier circuit. 6.b) Draw the load line using parameters which are found above and show Q point on it? VcC Rc = ... RB C; ... IB(p) Figure 5. Power Amplifier Circuit

6) Determine the following parameters according to power amplifier BJT circuit which is given below. 6.a) Calculate input power, output power and efficiency of the amplifier circuit. 6.b) Draw the load line using parameters which are found above and show Q point on it? VcC Rc = ... RB C; ... IB(p) Figure 5. Power Amplifier Circuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q. What is the purpose of using DC supply in amplifiers & oscillators circuits?
1 The AC input to a common emitter amplifier (Figure 1) is such that it is comparable to thermal voltage VT. For such an amplifier: a. Please show how a hybrid – T small-signal model would look like. Do not ignore early effect. b. Please derive relation for the terminal voltage gain and overall voltage gain. Vcc Rc R RE C Figure 1 You uolont oirouit
One of the following is not a property of a common-emitter amplifier: Select one: a. high voltage gain b. No phase inversion c. high current gain d. Emitter is at ac ground
With an aid of a. c. equivalent circuit, derive an equation representing common- mode gain (Ac) of the circuit.
A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is 50μA. Collector voltage is 10 V and biasing voltage being +20 V. Find followings a. Collector current b. Resistance (R1) c. Collector voltage , Emitter voltage , Base Voltage & Collector-Emitter Voltage.
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
Draw the dc and ac equivalent circuits for the amplifier. Determine the voltage gain of common-source amplifier.
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. Calculate the current gain, the input resistance, and the output resistance.
MOSFET Amplifier: 1. Determine the drain-to-source voltage (VDs) if VDD = +1sV and RD = 6202. The MOSFET data sheet gives and Ipss = 12 mA. (Ans: Vps=10.6 V) %3D
3. Write down which transistor structure each curve characteristic belongs to in the figure. Ip -VGS -VGS +VGs (c) VGS (b) (a)
Q1. (a) Consider the amplifier circuit in Figure Q1(a). Given the following: RI = 100 k2 R2 = 56 kN Rc =2 k2 Vcc = +8 V Assume the transistor has B = 100 and VBE(on) = 0.7 V. You may neglect Early effect and use VT = 26 mV. (i) Draw the DC equivalent circuit, then determine Iç and VCE. Draw the AC equivalent circuit using re model. Based on this, determine the parameters Av, Rin and Rout. (ii) Vcc Rc R1 R2 C3 Vout C2 Ci Vin Figure Q1(a)
draw the following systems: 1- AM generation -Square law product. 2- PM generation- frequency modulator.