69. Which of the following instrument is used for angular measurement? Select one: a.COMPARATOR b.MICROMETER c.SINE BAR d.OPTICAL FLAT
Q: Q.6) Complete the following table: No. Part of vernier calliper 1 Main Scale Vernier Scale 3 Screw
A: The main scale reading is that to the left of the zero on the vernier scale. The vernier reading…
Q: The advantage of Vernier caliper over Micrometer is Select one: O a. Both devices not useful O b.…
A: Option d is correct.
Q: Steps in the procedure of measuring the volume of liquid using a graduated cylinder.
A:
Q: 6. What is accuracy in measurement?
A: Measurement: It is the numerical quantification of the attributes for a body that are used to…
Q: In transition fit, tolerance zone of hole is entirely above that of shaft tolerance zones of hole…
A:
Q: Displacement Volume - Retraction 11 Calculate the volume of the cylinder during retraction.…
A:
Q: - The dimensions for the shaft size are o10*00 0.009 mm and the hole size are b 10*0.015 +0.000 mm.…
A: Shaft sizeϕ10-.009+0.00Maximum limit of shaft =10+0.000=10.00 mmMinimum limit of shaft=…
Q: 6. What material is used 7. What is the unspecified tolerance for angular dimensions? 8. What is the…
A: Given figure CHART DOWEL SPLIT TYPE TO FIND : 7 .What is the unspecified tolerance for angular…
Q: per use to block mo
A: introduction: In the steel business, the vernier calliper is a crucial tool. It's a tool for…
Q: Differentiate between operation (i) Plain Turning and Facing operation…
A: Plain turning and Facial operation: plain turning is the operation of removing extra amount of…
Q: Try square is a measuring tool used to measure the straightness and squareness of a workpiece.…
A: The square of the measure consists of two main elements, the blade, often referred to as a beam or…
Q: The depth measurement is done by ___________________part of a Vernier Caliper. Ratchet Anvil Spindle…
A:
Q: Describe two scales in Vernier Caliper?
A: Vernier caliper instrument is mainly used for taking accurate linear measurements. Vernier caliper…
Q: among the ruler and vernier caliper gave the least % err
A: Ruler and vernier caliper both are measuring devices.
Q: ribe a situation where you might use a Vernier caliper or micrometer. Explain why you would use this…
A: We need to discuss where we can use vernier caliper/ micrometer
Q: What is center of percussion? Write down Procedure for finding COP of a wooden compound pendulum
A: Given;To define contre of percussionTo write procudure for finding COP of a wooden compound…
Q: What is the lowest allowable dimension for the flats?
A: Solution:
Q: 1st image : What is the reading on the micrometer? 2nd image : What is the reading on the…
A:
Q: How can angular displacement be determined by angular acceleration?
A:
Q: If the basic diameter of shaft is 20mm with -0.02mm unilateral tolerance, and diameter of hole is…
A:
Q: What is an advantage of advantage of the metric system over the u.s. customary system?
A: The metric system is a worldwide standardly used unit system for measurements and it is used in…
Q: 9) To obtain a guide for centering irregular shaped workpiece in the lathe, its face should be laid…
A:
Q: ___________ tool is used for verifying the flatness of the component. A. Protractor…
A: Protractor is a device used to measure the angles. Engineers square is a checking tool which is used…
Q: What component does a tubular inside micrometer include that allows it to measure a wide range of…
A: Adjustable anvil is the correct answer.
Q: The tool used for marking center is __________. a. Steel rule b. Divider c.…
A: Solution:
Q: What is the use of gyroscope compass?
A: Gyroscope compass is a nonmagnetic device based on spinning disc and rotation of earth.
Q: The advantage of Vernier caliper over Micrometer is Select one: a. Both devices not useful b. Not…
A: vernier calipers is used to measure inner, outer dimensions and depth can also be measured.
Q: er than 5mm annot be used when position ta han 0.1mm annot be used when position ta er than 4mm
A: Given Data : Counter sink fasteners
Q: Which of the following is not a type of direct measuring instrument? a Micrometre Ob Vernier…
A: Among the given instrument names, it is required to state the name of the instrument that is not a…
Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…
A: 1—position 2 – the shape of the tolerance zone
Q: Which of the following will brake of blades O a.
A: Angle Of Blades
Q: Explain anyone practical measurement system with all of its functional elements.
A:
Q: List three rules to follow when using or storing semi-precision measuring tools.
A: Semi precision tools are used for the measurement of the various dimensions of the workpiece.
Q: what is the most digital multimeters can measure?
A: A digital multimeter is a measuring instrument used to measure two or more electrical values mainly,…
Q: State any THREE conventions in dimensioning.
A:
Q: Countersinking process is carried out by using twist Drilll. O True O False
A:
Q: 18. Which is not an equation for determining RPM: A. surface speed x 12/ pix diameter (in.) B.…
A:
Q: Surface grinding is done to produce
A: grinding is a machining operation in which extra material on the workpiece is removed. in grinding,…
Q: Right the accuracy in millimete
A: The screw gauge with a micrometer. The micrometer screw gauge is used to measure dimensions that are…
Q: With what precision caliper type can we measure 19,86 mm measurement? O A) 1/10 mm O B) 1/50 mm C)…
A: We can measure the value if the least count is come to the smallest measuring range...
Q: From the value in table 1.1 calculate the precision of Oth measurement?
A: Precision refers to the consistency of an instrument. It can be calculated as following: Precision =…
Q: wheel
A: Correct answer is given below
Q: A steel cylinder 5 inch in diameter is to be machined in a lathe. If the desired linear velocity of…
A: Given information V=2.3 ft/sec=2.3*12 in/sec, D=5in
Q: Which of the following is the correct sequence of the ability of the machining process to produce…
A: There are many processes which are used to get better surface finish. The type of machining process…
Q: Identify the part not belonging to micrometer. Frame Ratchet Locknut Clamp
A: Identify the part not belonging to micrometer. Frame Ratchet Locknut Clamp
Step by step
Solved in 2 steps
- Draw front and top view of the following isometric drawing of a bushed bearing. All dimensions in mm. Scale 1:1.High precision in angular measurements can be made using a sine bar. For using a 300 mm sine bar to inspect an angle on a part. The angle has a dimension of 37 45' and the sine bare rolls have a diameter of 40 mm. Determine: (a) The height of the gauge block stack (value accurate to four decimals). (b) The total number of gauges used including protector slips.Solve using parallelogram and Trigonometry please explain how
- For using a 200 mm sine bar to inspect an angle on a part. The angle has a dimension of 49º 20’ and the sine bare rolls have a diameter of 35 mm. What is the height of the gauge block stack accurate to four decimals.Which method specifies the tolerance by providing dimensions for the upper and lower limit in place of the dimension? a. general tolerance b. angular tolerance c. single-unit dimensioning d. plus-minus dimensioning e. limit dimensioningHigh precision in angularmeasurements can be made usinga sine bar. For using a 200 mm sinebar to inspect an angle on a part. The angle has a dimension of 49 degree 20' and the sine bare rolls have adiameter of 35 mm. Calculate the height ofthe gauge block stack is accurate tofour decimals.
- Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary dimensions as basic. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.Chapter 2: 6. Angular units of measurement are specified either in 7. Each feature must be or . Those dimensions specifically identified as reference, maximum, minimum, or stock do not require the application of a tolerance. and of the feature. 8. Dimensions must be selected and arranged to suite the function and mating relationship of a part and must not be subject to more than one 9. Unless otherwise specified, all tolerances and datum features apply for the full 10. Unless otherwise specified, all dimensions and tolerances are applicable at 11. What are the three types of direct tolerancing methods? 12. Where specifying decimal inch dimensions, a (temperature). Compensation may be made for measurements made at other temperatures. and is never placed before the decimal point for values less than one inch.State any THREE conventions in dimensioning.
- List 6 parts of Multimeter including each corresponding function.With measurement in diagram6. Angular units of measurement are specified either in 7. Each feature must be and of the feature. Those dimensions specifically identified as reference, maximum, minimum, or stock do not require the application of a tolerance. 8. Dimensions must be selected and arranged to suite the function and mating relationship of a part and must not be subject to more than one 9. Unless otherwise specified, all tolerances and datum features apply for the full 10. Unless otherwise specified, all dimensions and tolerances are applicable at 11. What are the three types of direct tolerancing methods? 12. Where specifying decimal inch dimensions, a or (temperature). Compensation may be made for measurements made at other temperatures. and is never placed before the decimal point for values less than one inch.