8- A converging elbow (see Figure) turns water through an angle of 135° in a vertical plane. The flow cross section diameter is 400 mm at the elbow inlet, section (1), and 200 mm at the elbow outlet, section (2). The elbow flow passage volume is 0.2 m³ between sections (1) and (2). The water volume flowrate is 0.4 m³/s and the elbow inlet and outlet pressures are 150 kPa and 90 kPa. The elbow mass is 12 kg. Calculate the horizontal (x direction) and vertical (z direction) anchoring forces required to hold the elbow in place. Section (1) D₂ = 200 mm D₁ = 400 mm 135 Section (2)

8- A converging elbow (see Figure) turns water through an angle of 135° in a vertical plane. The flow cross section diameter is 400 mm at the elbow inlet, section (1), and 200 mm at the elbow outlet, section (2). The elbow flow passage volume is 0.2 m³ between sections (1) and (2). The water volume flowrate is 0.4 m³/s and the elbow inlet and outlet pressures are 150 kPa and 90 kPa. The elbow mass is 12 kg. Calculate the horizontal (x direction) and vertical (z direction) anchoring forces required to hold the elbow in place. Section (1) D₂ = 200 mm D₁ = 400 mm 135 Section (2)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A converging elbow (see Figure) turns water through an angle of 135o in a vertical plane. The flow cross-section diameter is 400mm at the elbow inlet, section (1), and 200 mm at the elbow outlet, section (2). The elbow flow passage volume is 0.2 m3between sections (1) and (2). The water volume flowrate is 0.4 m3/s and the elbow inlet and outlet pressures are 150 kPa and 90 kPa. The elbow mass is 12 kg. Calculate the horizontal (x-direction) and vertical (z-direction) anchoring forces required to hold the elbow in place.
Q2/ A pump delivers water from a tank A (water surface elevation = 110 m) to tank B (water surface elevation = 170 m) as shown in figure below. The suction pipe is 45 m long ( = 0.024) and 35 cm in diameter. The delivery pipe is 950 m long (f = 0.022) and 25 cm in diameter. The head discharge relationship for the pump is given by H, = (90 – 8000 Q*), where H, in m and Q in m³/s. Calculate the discharge in the pipeline and the power delivered by the pump. Delivery pipe. elevation 170 m Suction pipe, elevation- 110 m Good Luck Rasha H. Salman
Q4 Water flows from a large reservoir to a smaller one through a 5cm diameter cast iron piping system, as shown in Figure below. Determine the elevation z₁ for a flow rate of 5 L/s. ₁ =? Sharp-edged entrance - Standard elbow, flanged =₂=4m Gate valve fully open D=5 cm -System boundary 9m 80 m -Exit
The spiral conical draft tube are connected to Francis turbine. The diameters of the internal and external of tube are equal to 60 cm and 90 cm respectively. The tube should be drowned-approximately 1.5 meter below the lowest tail race level and draft tube high of 600 cm. The velocity at the exit is 1.5 meter per second. (Friction head loss in draft tube = 0.034 m ), calculate:- Find the pressure head at the entrance and the bottom in m of water and in Kg / cm?. the total heads at the same point with reference to the tail race as a datum find the power at the entrance and bottom the efficiency of a draft tube
A 50 mm diameter siphon discharges water from a reservoir (Point 1 elev 20m) into open air (Point 3 elev. 10m). The head loss from the reservoir (point 1) to the summit (point 2 elev =22m) is 3 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. Determine the velocity in the siphon in m/s? 1 The correct answer has a margin of 0.05 from the exact answer. 2.
The square-section duct in atmospheric conditions is exposed to air flow from outside as seen in the figure. Air temperature Tair=5°C velocity Vair= 10m/s. entering the canal at a flow rate of Mwater = 0.01 kg/s and a temperature of Twater = 50°C, Find the outlet temperature of the water. Geometric dimensions are given on the figure.
Please include a free body diagram Three pipoes A,B and C coonected in seies discharges 160 L/s of water. The properties of pipe: for pipe A,L= 1800 m, diameter= 0.90 m f= 0.012; for pipe B, L= 1500 m, diameter= 0.60 m f=0.012 and for pipe C, L= 800 m , diameter = 0/45 m, f= 0.012. Disregarding minor losses, find the diameter of an equivalent single pipe which can replace the three pipe. a. 0.750 m. b. 0.492 m. c. 1.15 m. d. 0.574 m.
(1) shown in the figure below is only 2 mm in diameter. Take water density p dynamic viscosity u = 0.001 kg/(m.s) In Tinyland, houses are less than a foot high! The rainfall is laminar! The drainpipe = 998 kg/m and (a) When the gutter is full, simplify the steady flow energy equation by neglecting the gutter velocity and using the head loss due to a laminar flow, determine the draining velocity V and draining flow rate Q. (b) The gutter is designed for a sudden rainstorm of up to 5 mm per hour. For this condition, what is the maximum roof area that can be drained successfully? (c) What is the Reynolds number Rea? Water Tinyland governor's mansion 20 cm
Water is flowing in a piping system as shown tin figure, Find the i. diameter of section 2 pipe. ii. Mass flow rate in section 1 Section 1 Q1= 0.4 m /s d1=30 cm Section 3 Q3=0.7 m/s V3= 5 m/s Section 2 V2=4 m/s d2=?
2500kW power is generated shown in the Figure with a water flowrate of 20 m3/s. The head loss for the entire flow is 2.5m. (a) Find the pressure difference P1 - P2 across the turbine. (b) Find h You can neglect the head loss between point 1 and 2.
Problem Set No. 1 1. A 200 kg chunk of lead falls from a height of 30 m and smashes into a rigid concrete floor. Calculate the increase in the internal energy AU (MJ), assuming that no energy is transferred as heat from the lead. 2. Assess the capabilities of a hydroelectric power plant from the following field data: Estimated water flow rate, 40 m³/s River inlet at 1 atm, 10 °C Discharge at 1 atm, 10.2 °C, 200 m below the intake 3. How much energy transfer as heat is required to evaporate completely 1 kg of nitrogen for a constant pressure process, with T = 89.5 K? 4. One kg of CO₂ is heated in a 0.5 m³ vessel from -18 °C to 93 °C. Determine the initial and final states, and the amount of energy transfer as heat to the CO2. 5. The condensate pump on the Navaho power plant raises the water pressure from 3.5 in of mercury to 390 psia at a flow rate of 5,100 gal/min. If the pump isentropic efficiency is 0.8, calculate the power required in hp. 6. Calculate the thermal efficiency of a…
3) The system in the Figure consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m³/s of water at 20°C into the reservoir? 45° Open globe 45° Elevation 500 m = Sharp exit