8. A concrete wall footing With a Width or and a depth of 0.6 m supports a centrally placed 0.6-m-thick wall. The ultimate bearing stress for the soil under the footing is 47 kN/m2. What is the height of the wall if a factor of safety of 5.0 is used? Concrete weighs 23.5 kN/m3 (assume depth of one meter) NOTE: please check options

8. A concrete wall footing With a Width or and a depth of 0.6 m supports a centrally placed 0.6-m-thick wall. The ultimate bearing stress for the soil under the footing is 47 kN/m2. What is the height of the wall if a factor of safety of 5.0 is used? Concrete weighs 23.5 kN/m3 (assume depth of one meter) NOTE: please check options

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

Show all calculation and formula used: The second floor portion of a house is about to break down, so it was propped up by an iron column 4.0 meters long with cross sectional area of 30.0 cm^2. The iron column was compressed by 0.015 mm. How much load (N) the iron column is supporting? Y of iron = 19x10^10 Pa
You are asked to design a cylindrical steel tank to hold 100,000 liters of benzene. Calculate the thickness in mm required for the following heights. You can assume Oiensile = Design tensile strengths for different pressure vessels can be found in ASME Codes and Standards for pressure vessels. (ASME – American Association of Mechanical Engineers). 15,000 kPa. а. 8 m b. 6 m с. 4 m d. What are the advantages of a taller and thinner tank? e. What are the advantages of a shorter and wider tank?
A 129 ft tower is located on the side of a mountain that is inclined 19* to the horizontal. A guy wire is to be attached to the top of the tower and anchored at a point 42 ft downhill from the base of the tower. Find the shortest length of wire needed. 129 ft 42 ft 19° NOTE: The picture is NOT drawn to scale. length of guy-wire = ft
Y = 9810 N m FH METHOD 1: Plane Surfaces METHOD 2: Curved Surfaces Fv TAKE NOTE: Use the 2 methods to solve the problem. COMPARE/DIFFERENTIATE THE TWO METHODS. Plane Surfaces F=? 45° gate width=1m 1m Curved Surfaces Directions: Guide Question/s: 1.) Using the procedure employed in calculating FH, F, and F in a curved surfaces, will it be applicable also in calculating the hydrostatic force F in an inclined rectangular gate?
Homework 6- Attempt 1 roblem 9.122 The concrete "gravity" dam is held in place by its own weight (Figure 1). The density of concrete is Pc = 2.5 Mg/m³, and water has a density of P = 1.0 Mg/m³. Suppose that a = 1.5 m h = 7.5 m. igure a A -d-a- -d- h Part A 6 of 10 > ■Review Determine the smallest dimension & that will prevent the dam from overturning about its end A. Express your answer to three significant figures and include the appropriate units. d= 3.77 A m Submit Previous Answers Request Answer ? Incorrect; Try Again; 17 attempts remaining
A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance measured along the beam; [x]=[L] y = displacement of the beam; [y]=[L] = circular frequency of vibration; []=[T1] = mass of the beam per unit length; []=[ML1] D = bending rigidity of beam; [D]=[FL2] Show that the equation is dimensionally homogeneous. Note that [F]=[MLT2] see Eq. (1.21:).
A foundation must be built on a non-cohesive soil that has the following characteristics: soil density = 18.0 kN/m3, saturated soil density = 19.0 kN/m3, internal friction angle of 30°, depth of planting = 1.5 m and depth of water table = 0.8 mThe gross allowable load with FS = 3 is 700 kN. Determine the dimensions of the proposed footing using Meyerhof theory.
A composite spring consists of a steel close-coiled helical spring and a bronze close- coiled helical spring arranged in series. Data for the springs are given in the table below: Steel Spring Bronze Spring D 40 mm 40 mm 4.5 mm 4.5 mm G 80 GPa 40 GPa TAllowable 250 MPa 181 MPa 10 Determine the ratio between the number of coils in each spring if the deflection of the two springs is to be the same. Calculate the number of coils of the bronze spring Calculate the maximum load that can be carried by the composite spring. Determine the total extension of the composite spring when subjected to the maximum load. * Calculate the total strain energy in the spring assembly.
The cable supports a railway bridge between two tunnels. Given: Distributed load, w = 1.01 MN/m Allowable cable tension, Talllow = 47.2 MN. Distance, a = 21 m a a What is the corresponding value of "h" in meters? Express your answer in 1 decimal place. 3
5. An engineer is planning to use gabion retaining wall to protect a section of Kennon road from landslide. A gabion is a wire mesh container filled with rocks. The engineer must estimate the volume of the rock to be used. If the gabion wall will have a thickness of 5ft, estimate the volume of the rocks given the measured depth of the wall every 10 ft of its width based from the road level. width, ft 10 20 30 40 50 60 70 80 90 depth, ft 5 12 20 18 17 13 10 5 a.) estimate the area of the wall using multiple trapezoidal rule with n=9 b.) estimate the area of the wall using single application of Simpson's 3/8 rule c.) estimate the volume of the rocks to be used using the area in a.) and b.)
a) Column is one of a structural element in a building. The column is made of a steel pipe with total length, L = 1.2 m and modulus of elasticity is E = 210 GPa. The steel pipe has an inner diameter of di = 36 mm and outer diameter of d2 = 40 mm. Relate Euler's critical load, Per for each of the following cases. i) Pinned – Pinned ii) Fixed - Free i) Fixed – Pinned iv) Fixed – Fixed
Determine the parameters for each question below, assume E = 200 GPa. i) Critical load for the square column ii) Radius of the round column for which both columns have the same critical load iii) Express the cross-sectional area of the square column as a percentage of the cross-sectional area of the round column. |A 1'm Im 25 mm |D B