QUESTION 1. Cross-sectional dimensions ofa beam is given in the figure. The allowabletension and the allowable compression stressvalues that appear on the cross-section are(Otension)all = 150 MPa and (Ccomprassion)all = 100Mpa. Determine the resultant intermal bendingmoment value, M on the cross-section so the80 mm12 mmM100 mm8 mmallowable stress values are not exceeded.

Givenσtensionall=150Mpaσcompressionall=100Mpa

80 mm QUESTION 1. Cross-sectional dimensions of a beam is given in the figure. The allowable tension and the allowable compression stress values that appear on the cross-section are (Gtension)all = 150 MPa and (Ocompression)all = 100 Mpa. Determine the resultant internal bending moment value, M on the cross-section so the allowable stress values are not exceeded. 12 mm M 100 mm 8 mm

80 mm QUESTION 1. Cross-sectional dimensions of a beam is given in the figure. The allowable tension and the allowable compression stress values that appear on the cross-section are (Gtension)all = 150 MPa and (Ocompression)all = 100 Mpa. Determine the resultant internal bending moment value, M on the cross-section so the allowable stress values are not exceeded. 12 mm M 100 mm 8 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.9.9P: A U-shaped cross section of constant thickness is shown in the figure. Derive the following formula...

See similar textbooks

Similar questions

A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
The cross section of a sign post of constant thickness is shown in the figure. Derive the formula for the distance e from the cent crime of the wall of the post to the shear center S: where I2. = moment of inertia about the z axis. Also, compare this formula with that given in Problem 6.9-11 for the special case of ß = 0 here and a = h/2 in both formulas.
Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE= ILS mm,andV = 38 kN.
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A U-shaped cross section of constant thickness is shown in the figure. Derive the following formula for the distance e from the center of the semicircle to the shear center. Also, plot a graph showing how the distance e (expressed as the non dimensional ratio e/r varies as a function of the ratio b/r. (Let b/r range from 0 to 2.)
. A cantilever beam (width b = 3 in. and depth h = 6 in,) has a length L = 5 ft and is subjected to a point load P and a concentrated moment M = 20 kip-ft at end B. If normal stress trx= 0 at point C, located 0.5 in. below the top of the beam and 1 ft to the right of point Atfind point load P. Also show the complete state of plane stress on the element at point C.
YU Fixed end 4.25 KN.m 0.3m 5KN · 100 KN 100 KN 0.4 m 3.0 KN-m 5 KN 200 KN 200KN 0.1 m X Find the axial, torsional, bending and transverse shear stresses at the four critical points (top, bottom, left and right) of the central cross section. Draw the stress state cubes and then represent them as plane stress states, if applicable. This stainless steel beam has a circular cross section and a diameter of 7 centemeter
Z y q 0.3m 4.25 kN 5 KN 0.4m 100 KN 100 KN 3.0 kN m 0.1m 2 kN 2,00 KN 200 KN X This stainless steel beam has a circular cross section and a diameter of 7 centemeter. Find the axial, torsional, bending and transverse shear stresses at the four critical points (top, bottom, left and right) of the central cross section. Draw the stress state cubes and then represent them as plane stress states
A uniform wind load of q = 0.2 kN/m? acts on the billboard with dimensions of b = 1.5 m and a = 1 m. The allowable normal stress is oalow = 140 MPa, c = 0.5 m for the circular cross section panel pole. Draw the shear force, bending moment and torsional moment diagrams for the panel pole. a) Calculate the cross-section diameter d, using the maximum shear stress (Tresca) criterion. b) Calculate the cross-section diameter d, using the maximum distortional energy (von Mises) criterion. SOLUTION kesit
A WT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAg - 2 m, Lac- 7 m, Lco- 4 m, PA- 14 kN, Wac- 8 kN/m. Consider the entire 13-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam.
Find the max shear stress in a 200mm tall, 150mm wide rectangular cross section using the appropriate reduced shear stress equation. Assume Vmax = 12kN. Find the max shear stress in a W12x50 cross-section using the appropriate estimated shear stress equation. Assume Vmax = 236kips. Find the max shear stress in bending in the cross section below if Vmax = 10 kips. 10" Flange 2" Web 2" 8" Flange 2" 10" • Identify where in the cross section the max shear will occur. • Determine the thickness of the cross-section at the location you wish to find shear stress. • Calculate the Ix for the shape (assume bending in the x with most basic beams). • Calculate Q by dividing the section into two pieces at the point you want shear stress. Select one of the pieces (either will work), I picked the top piece. • Use the Shear Stress equation to determine the requested stress. • Compare you answer: Max shear stress = at the center of the cross section.
A WT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAB = 3 m, LBc = 7 m, LcD = 2 m, PA = 17 kN, WBC = 10 kN/m. Consider the entire 12-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. PA LAB Answers: (a) 07 = (b) oc= B 287.45 121.1 WBC LBC WT305 x 41 MPa. LCD क 88.9 mm 211.1 mm MPa. X