A 1,000-2 resistor is in series with a 2-mH inductor. An ac voltage source operating at a frequency of 100,000 rad/s is attached as shown in the figure. The impedance (N) of the RL combination is most nearly: 22. 1,000 2 2 mH O A. 200 + j1,000 O B. 1,000 + j200 о с. 38.4 + j192 O D. 1,000 – j200 ll

A 1,000-2 resistor is in series with a 2-mH inductor. An ac voltage source operating at a frequency of 100,000 rad/s is attached as shown in the figure. The impedance (N) of the RL combination is most nearly: 22. 1,000 2 2 mH O A. 200 + j1,000 O B. 1,000 + j200 о с. 38.4 + j192 O D. 1,000 – j200 ll

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
The rms value of the resultant current in a wire carries a dc current of 10 A and a sinusoidal alternating current of peak of value 20 A is-
In an experiment, the function generator is adjusted to generate a square voltage at a certain frequency. This voltage is displayed on an oscilloscope and the reading is 16 V peak-to-peak. The rms value of this voltage is .What will be the rms value of this voltage if the frequency is doubled? Select one: O 16 Vrms 32 Vrms O 8 Vrms . 8 Vrms ..... O 5.657 Vrms 5.657 Vrms ....... O 8 Vrms . 16 Vrms O 16 Vrms 8 Vrms ......
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
2-A resultant current is made of two components: a 10 A D.C. component and a sinusoidal component of maximum value 14.14. The average value of the resultant current is amperes (a) 0 (b) 24.14 (c) 10 (d) 4.14 and r.m.s. value is - amperes (e) 10 (f) 14.14 (g) 24.14 (h) 100
can you please give me the comple solution for this question, thanks. A certain voltage function contains a constant term, a fundamental and third harmonic. The maximum value of the fundamental is 85 % of the constant term and the maximum value of the third harmonic is 55 % of the constant term. If the effective value of this function is 180.3V, find the magnitude of the two harmonics. A.IstHarmonic = 75 V , 3rd Harmonic = 120V B. Ist Harmonic = 80 V , 3rd Harmonic = 125V C. IstHarmonic = 120 , 3rd Harmonic = 75V D. Ist Harmonic = 125 V , 3rd Harmonic = 80V E. NOTA
A voltage wave of 250 kHz has a Vmax-5 V and Vmin=-35 V. The duty cycle of this wave is 0.875. This voltage waveform has been applied across a 2.5 µH inductor for a very long time so that steady state has been achieved. Diagrams of the wave parameters and circuit are shown in this figure: L What is the average voltage of this wave? Average voltage = 35 V Voltage (arb, unit) 1.25 Minimum current: -3.5€ Amps 1 0.75 0.5 0.25 0 4.25 05 Have you integrated the wave over full cycle? 4.75 4 -1.25 Vmax 0.5 Vmin What is the average current flowing through the inductor? Average current = 3.56 A 15 Period/s On average, there is no power consumed by the inductor. Have you considered this? What are the maximum and minimum currents that flow through the inductor? Maximum current: 0.50 Amps D= 25 TH TH Have you used the relationship for current and voltage in an inductor? Have you considered the slope of the current wave?
Determine the rms current in the figure for Vrms = 16 V and C = 74µF V f=10 kHz
The below figure shows the waveform of the voltage and current in a purely inductive AC circuit. Voltage Current Using the voltage phasor as the reference, the current phasor Lags by 90° Is in phase with the voltage Leads by 90° Lags and then leads by 160°
Apply a sinusoidal input voltage with 2V p-p and vary the frequency according to the table below. Measure the voltage Vr and current I from the voltage across R and find the phase angle between the Vi and I.
How do I find the phase of this sinc function?