A 15 horsepower pump operating at 56% efficiency is moving water from below ground to ground level at a rate of 200 gallons per minute. The intake line has a diameter of 1.5 inches and a C value of 120. The water temperature is 60 degrees F. How far below the ground surface can the pump reach? Answer in feet to the nearest foot. Can the pump satisfy NPSH at this depth? Answer yes or no.

A 15 horsepower pump operating at 56% efficiency is moving water from below ground to ground level at a rate of 200 gallons per minute. The intake line has a diameter of 1.5 inches and a C value of 120. The water temperature is 60 degrees F. How far below the ground surface can the pump reach? Answer in feet to the nearest foot. Can the pump satisfy NPSH at this depth? Answer yes or no.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What size pump is needed to supply 10 gpm to a cylinder when the electric motor is rotating at 1725 rpm? Assume 100% efficiency and state your answer in in3/rev to two decimal places.?
A pump delivers 5000 gallons per minute of fluid with specific gravity of 0.9 at a head of 100ft. Find the horsepower needed for the motor if overall efficiency is 60% and motor efficiency is 80%. A. 142.18hp B. 178.45hp C 162.34hp D. 189.54hp
Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above the river (dimension "a" on the diagram below) and is supplied by a 6.00 inch schedule 40 pipe. The tank is 19.5 m above the pump (dimension "b" on the diagram below) and is supplied by a 4 inch schedule 40 pipe. The water level in the tank is 4.3 m above the inlet (dimension "c" on the diagram below). The pump delivers 0.021 m/s. Losses are estimated to be 1.2 m between the river and the pump, and 4.2 m between the pump and the tank. Discharge line Suction line Pump River a) Calculate the losses in the suction line in kPa, based on the given head loss in m. kPa b) Calculate velocity in the suction line in m/s. m/s c) What is the pressure at the inlet to the pump in kPa? kPa
Use the Goulds Pump Selection System to find a pump capable of delivering at least 500 gpm against an elevation gain of 120 ft. Use 150 ft as the pump head to be safe.
URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by step solution. Box the final answers. Do not shortcut your solution. I will give an upvote if it satisfies. Thank you! If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a. What is the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? b. How much power is required to drive it if the diameter of the suction side is 600mm? c. If the pump is rated at 120hp, what is the efficiency of the pump neglecting energy losses in the system?
A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
Seven hundred gpm of water are being discharged by a centrifugal pump 5 ft. above the pump inlet. The inlet pressure is 4-in Hg above atmospheric and the discharge pressure is 29 psia. Assume the pump input is 8 hp, if the pump has an 8-inch diameter inlet and a 4-inch diameter discharge: 1.How much pressure loss in the pump? a. 28.4 ft-lbf/lb b. 5 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 2. How much is the velocity loss in the pump? a. 28.4 ft-lbf/lb b. 45.3 ft-lbf/lb c. 4.7 ft-lbf/lb d. 38.1 ft-lbf/lb 3. If the pump speed is increased from 1600 to 2400 rpm, what will be the new net flow rate in the pump? a. 800 gpm b. 1050 gpm c. 1400 gpm d. 1965 gpm 4. Find the new brake horse power if the pump speed in increased from 1600 to 2400 rpm. a. 64 hp b. 20.25 hp c. 8 hp d. 30.375 hp
A cylinder with a bore of 4.5 inches and a rod diameter of 1.5 inches is to be used in a system with a 6 GPM pump. What is the extension speed of the cylinder?
a pump at 1750 rpm delivering 600 rpm aganist a total head of 200 tt. change in the filling system have increase the head of 450 feet. at what rpm should the pump be operate to achieve this new head at the efficiency?
In order to meet the stated goal of delivering 4 gallons per minute at a height of 670 meters, a single pump must have a maximum flow rate of 40 gpm. How many stages are needed if the speed cannot exceed 1352 rpm?
a. the total dynamic head in meters b. the water power in kW c. the motor horsepower if the pump efficiency is 66%
A pump with an impeller diameter of 0.02 m, an impeller speed of 58.3 rpm, a * total capacity of 12 L/s, an available head of 70 m, and a brake power of 12 kW is used to pump water. Determine the capacity of a homologous pump with twice the impeller diameter and operating at half the speed. Choices: A.60L/S B.36 L/S C.48 L/S D.72L/S