A 150 HP, 3-phase, 6 pole, 460 V, 60 Hz induction motor draws 195 A line current at full load speed of 1170 rpm and 0.85 pf. Solve for the percent slip at full load. (a). 2.5% (b). 3.0% (c). 2.8% (d). 2.0%

A 150 HP, 3-phase, 6 pole, 460 V, 60 Hz induction motor draws 195 A line current at full load speed of 1170 rpm and 0.85 pf. Solve for the percent slip at full load. (a). 2.5% (b). 3.0% (c). 2.8% (d). 2.0%

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Related questions

Q: b) A 20kVA 8000/277V distribution transformer has the following resistances and reactances: Rp = 320…

A: This question is related to single phase transformers

Q: The position of modulation in a transmitter determines whether the circuit is low- level or…

A: The Amplitude Modulation scheme is implemented to transmit a low power signal over large distances…

Q: 6.) A voltage v = 320 sin (100t + π/3) is applied to a resistor of 43 ohms. Find the value of power…

Q: The values of Vmax and Vmin as read from an AM wave on an oscilloscope are 2.6 V and 0.29 V…

Q: A three-phase source has a phase sequence of EAS- Esc - ECA and delivers the following delta load…

Q: Assume that is(t) = 4√2 cos(2t) A in the circuit below. Use Thévenin/Norton, series-parallel…

A: To calculate Thevenin equivalent impedance,we deactivate the independent sources and calculate the…

Q: Two balanced three-phase motors in parallel, an induction motor drawing 400 kW at 0.8 pf lagging and…

A: Power Triangle is the right angle triangle it represent the reactive active and apparent power .…

Q: The diagram below shows a mid-point reactor tap-changer in one phase of transformer winding. What is…

A: Given A circuit diagram of mid-point reactor tap changer. We need to determine the purpose of…

Q: . Choose the correct answer for the power of element 2 and identify if the power is consumed or…

Q: * 12. Evaluate y"+y' = 0; y(0) = 0, y'(0) = 1

Q: The word "carrier shift" is frequently misunderstood or misinterpreted. Carrier shift is also known…

A: According to the question, we need to select the true statement.

Q: A balanced delta-connected load with impedance per phase of 30/30° is connected to an abc-sequence…

Q: A three-phase source has a phase sequence

A: Active Power- It is power utilized by the load. Active power is equals to the multiplication of…

Q: circular flat surface has a radius of 3.5 ft in a uniform magnetic field. Calculate the magnetic…

Q: C + EAN A B Ia Vca – 20 Ω, + -j 15 0 Ica/co Lab Vab -j15 Ω -be 20 Ω 20Ω –j 15 Ω www 46 Vbc +

Q: Three audio waves with 100, 200 and 300 volts amplitude respectively, simultaneously modulate a 450…

Q: Ceramic Filter Band-reject Filter Butterworth filter Chebyshev Filter Commutating Filter Bandpass…

A: Here are few questions related to the filter, related to its frequency range and it's selectivity.

Q: 9.16. What are the values of VH, V₁, VREF, AV, the noise margins, and the average power dissipation…

A: Kirchhoff Voltage Law: KVL is the sum of the voltages in a closed circuit at node when circuit is…

Q: 7 WHAT IS THE MAGNITUDE OF THE SURFACE MAGNETIC FIELD B CREATED BY A CURRENT I CIRCULATING IN AN…

Q: QUESTION 2 Consider the feedback system illustrated: r(t) S+3 where C(s) = s(s+10) and G(s) == Which…

Q: Sketch the signal x(n) shown below as: 1. xn) u(l-n) ال 4 3 2 1 0 1 2 3 4 5

Q: For the circuit in the figure, Rab =6002, Zbc = 8022+ j6022. Compute the following: a. Phase and…

Q: The Laplace transform of f(t) = sin() is: Select one: O F(s) = 2 (28)²+1 O F(s) = 2+1 28 O F(s) =…

Q: 1. Z-Transform of 8(n+3) is a) z b) z² c) 1 d) z³ 2. A system which is linear is said to obey the…

Q: 4. An RC filter stage (R = 33 02, C = 120 µF) is used to filter a signal of 24 V dc with 2 V rms…

A: It is given that: R=33ΩC=120μFVdc=24 VVrms=2VIL=100 mA

Q: Q Using mesh current analysis technique to find the current , in the circuit of Figure below. 6 cos…

Q: Produce a ladder diagram that will cause output Y to go HIGH when switch A and B are closed OR when…

A: Ladder Diagram: Industrial control logic systems are documented using ladder diagrams. Ladder…

Q: 2. Sketch the output V and determine the DC level of the output signal for the given network below.…

A: The given circuit is full wave rectifier which means for both positive and negative half cycle of…

Q: = 1. For the circuit shown below, the values are Vab=20020°, Vbc = 200/120° and Vea 200/240° V, Z4…

A: Given circuit Where Vab=200∠0° V Vbc=200∠120° V Vca=200∠240° V And Z4=Z5=Z6=25∠30° Ω…

Q: Passes frequencies below a critical frequency called the cutoff frequency and greatly attenuates…

A: Answer is given in step 2 & step 3 for Q32(7) & Q32(8) respectively

Q: Does maximum power transfer imply maximum efficiency of power transfer? Explain

A: In this question we will write that maximum power imply maximum efficiency or not....

Q: = A three-phase source has a phase sequence of EAB - EBC - ECA and delivers the following delta load…

Q: A 3-phase system has a single phase to earth fault (i.e. phase A is short circuit to earth while…

A: here sigle line to ground fault with zero fault impedance fault current Ia calculated as-

Q: 5. The maximum load on the Thermal Plant of 60MW capacity is 50MW at an Annual Load Factor of 50%.…

A: Thermal power plant is generate the electricity . it is also known as a combustion power plant . it…

Q: This circuit is used in low-level AM transmitters to increase the amplitude of the source signal to…

A: To name the circuit which is used in low-level AM transmitters to increase the amplitude of the…

Q: KIRCHHOFF'S RULES (2 LOOPS) Determine the current through, voltages across, and the power dissipated…

Q: 1.2 A ring has two halves. The one half is made from Cast iron, while the other is made from Cast…

A: It is given that: Lr=1mm=1×10-3mA=345mm2=345×10-6m2L=0.6mThe length of core…

Q: - coupled. 1- The primary and secondary of a transformer are ---..... a) Electrically b)…

A: Based on the bartleby guidelines solved the first three questions. 1. Answer: Magnetically…

Q: Evaluate and Sketch the convolution between fi(t) and f2(t) defined in Figure ( fi(t) f₂(1) 8 Figure…

A: Convolution of F1(t) and F2(t) can be done by the following procedure

Q: 10.22: For the following electric circuit, find Z and Y parameters? Also, compute input and…

Q: Determine the following in Combination network. Draw the ac euivalent circuit. Zin Zo Av Ai Vo

A: The dc analysis of the circuit will be Gate voltageVG=10k50k×16VG=3.2VVoltage at emitter terminal…

Q: An inductor of 2H is connected to a circuit at a frequency of 50Hz. Compute the inductive reactance…

Q: Calculate the current I0 in the following circuit:

A: The required current io cam be calculated by using mesh analysis. The kirchhoff's voltage law should…

Q: how was the load 300<-36.86 achieved?

A: We know that power factor can be represented in terms of cosine function as shown below.

Q: The transfer functions of two compensators are given below: G₁ (8) = 10(s+1) (s+10) and G₂ (s) =…

A: Given, The transfer function of two compensators G1s=10s+1s+10G2s=s+1010s+1

Q: A preselector and an amplifier stage make up the RF portion. The RF amplifier determines the…

A: RF is a radio frequency amplifier is amplifier used for the conversion of low-frequency signals to…

Q: b) Outline any THREE constructional differences between the single-value capacitor motor and the…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: How did you know if the battery is charging in TP405

A: Introduction - The TP4056 is a comprehensive constant current/voltage linear charger for individual…

Q: A single-pole causal LTI system has the following impulse response given below. h(n) n Which option…

Q: A 54 conductors/phase three phase lines are spaced asymmetrically but transposed uniformly. The…

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

A 150 HP, 3-phase, 6 pole, 460 V, 60 Hz induction motor draws 195 A line current at full load speed of 1170 rpm and 0.85 pf. Solve for the percent slip at full load.

(a). 2.5% (b). 3.0%

(c). 2.8% (d). 2.0%

A 150 HP, 3-phase, 6 pole, 460 V, 60 Hz induction motor draws 195 A line
current at full load speed of 1170 rpm and 0.85 pf. Solve for the percent slip
at full load.
(a). 2.5%
(b). 3.0%
(c). 2.8%
(d). 2.0%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 concept

VIEW

Step 2 calculation

VIEW

Step 3 final answer

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.
Explain in detail the Starting of Induction Motors
6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
Frequency of emf in the stator of a 8 pole induction motor is 50Hz and the rotor emf frequency is 1Hz. The motor speed is ................ Answer
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights. design the single-phase, full-wave, ac/ dc converter. show design specifications, the reason for DC motor selection. correct manual circuit, and correct automatic closed-loop control circuit
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
Draw the typical speed-torque characteristic of the induction motor and expain it.
A four-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. If the dc-to-ac converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source.
• Q5/ in a DC motor. List and describe the types of losses that occur
A 3-phase induction motor has a starting torque 100% and a maximum torque of 200% of the full load toque. Find the slip at maximum torque. Answer: 26.8%