A 2 m copper bar subjected to a tensile load 180 kN is suspended from a pin that is supported by two identical steel posts as shown. Determine the total deformation of the lower end of the copper bar due to the applied tensile load. HINT: Note that the steel posts support the pin where he copper bar is attached. Use 3 decimal places in every solved value. steel post L = 0.5 m A = 4500 mm? E = 200 GPa соррer bar L = 2 m A = 4800 mm² E = 120 GPa

A 2 m copper bar subjected to a tensile load 180 kN is suspended from a pin that is supported by two identical steel posts as shown. Determine the total deformation of the lower end of the copper bar due to the applied tensile load. HINT: Note that the steel posts support the pin where he copper bar is attached. Use 3 decimal places in every solved value. steel post L = 0.5 m A = 4500 mm? E = 200 GPa соррer bar L = 2 m A = 4800 mm² E = 120 GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 18 ksi, determine the maximum load that can be applied to each component. (a) 1 in. (b) The maximum load that can be applied to component (a) is The maximum load that can be applied to component (b) is lb. lb.
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between the jaws. In this case; a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the figure. b) Show the distribution of normal stresses across the section height. (draw) c) Since the clamp material has tensile strength (apull) safety = 50MPA and compression safe stress (opress) safety = 80MPA, what is the great compressive load (P) that can be applied without damaging the a-a section? %3D %3D (Please solve in detail and according to engineering rules.) Material mechanics Sectional view a-a - 20mm T. 183mm 40mm
a. Calculate "P" in KN considering tension failure on gross area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
!! Show Complete & Detailed Solution w/ FBD !!The figure shows that when the rigid bar is in the horizontal position, the wires are unyielding. The bar rotates clockwise about the pin B through an angle of 2.1° when a force is applied at the handle. Determine the average normal strain developed in wires.a. AHb. CGc. DF
SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the bearing stress in each bolt. F 150 mm Force "F" is equal to F 200 KN. The diameter of each bolt is 20 mm. 50 mm 340 mm
A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa
PROBLEMS: 1. The bolt connection shows 8-22mm diameter bolts in a bolt hole diameter of 25 mm and spaced according to the following: Sı = 40mm T = 16mm S2 = 80mm S3 = 50mm S4 = 100mm te = 12mm Determine the force T if the allowable tensile stress is 200 MPa, the allowable bolt shear stress is 120MPa and the allowable plate bearing stress is 120 MPa. 2. A long retaining wall is braced by wood shores set at ang angle of 30° and supported by concrete thrust blocks as shown. The shores are evenly spaced, 3m apart. For analysis purposes, the wall and shores are idealized on the second image. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall I assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the wall is F= 190KN. If each shore has a 150mmx150mm square cross section, what is the compressive stress in the shores? Retaining wall Soil Concrete Shore thrust block 30 30 1,5 m…
1. A fork joint connects two links as shown in the figure. What is the number of DOF of this system? Prove.