A 2-wire d.c. street mains AB, 600 m long is fed from both ends at 220 V .Loads of 2O A, 40 A, 50 A and 30 A are tapped at distances of 100m, 250m, 400m and 500 m from the endA respectively. If the area of X- section of distributor conductor is 1cm2, find the minimum consumer voltage. Take p = 1-7 x 10-6 Q cm. * 220 V

A 2-wire d.c. street mains AB, 600 m long is fed from both ends at 220 V .Loads of 2O A, 40 A, 50 A and 30 A are tapped at distances of 100m, 250m, 400m and 500 m from the endA respectively. If the area of X- section of distributor conductor is 1cm2, find the minimum consumer voltage. Take p = 1-7 x 10-6 Q cm. * 220 V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. Find the average power spent by the load circuit?
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3- phase side. The main transformer primary to secondary turns ratio is (12/1).
use kirchhoffs Junction rule and loop rule to solve for currents I1 , I2 and I3..
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
60. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the real power. a. 65.3899 b. 392.4372 c. 397.848 d. 588.6559
Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent circuit elements are as follows R1=0.10 x1=0.20 R2= 0.250 X2 = 0.75 RO = 500 XO = 150 It feeds a 90 kVA load at a voltage of 2000 volts and a power factor of 8.0 delayed. Calculate the initial voltage and current? Rogl JXql a Mmm T I', 2₁ Acti Go to
If the core of LVDT is at the middle, then the output voltage will be a. maximum b. minimum c. Output voltage is no relation with core position d. 0
Problem 5 Consider a three winding transformer with the following particulars: = Z₁ Z2 Z3 =0.02 + j0.08 £, V₂ = 400 V, 12 = 60/30° A, and I3 = 50/-40° A. Assume that V₂ is the reference phasor, calculate: The intermediate voltage Vo. a. b. The primary current I₁ and the primary voltage V₁. c. The tertiary voltage V3 referred to the primary side. d. The apparent powers and the power factors at the primary, secondary and tertiary terminals. e. The transformer efficiency.
A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So