A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 4 teeth/in drives a 30-tooth gear. The two shafts are at right angles and in the same plane. The illustration below shows a typical right-angle bevel gear set. Bevel gear pitch diameters are measured on the outside face along the back-cone, as shown in the figure. Calculate the face width of the gearset, in inches. Note: use table 13-3 to calculate face width.

A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 4 teeth/in drives a 30-tooth gear. The two shafts are at right angles and in the same plane. The illustration below shows a typical right-angle bevel gear set. Bevel gear pitch diameters are measured on the outside face along the back-cone, as shown in the figure. Calculate the face width of the gearset, in inches. Note: use table 13-3 to calculate face width.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 4 teeth/in drives a 30-tooth gear. The two shafts are at right angles and in the same plane. The illustration below shows a typical right-angle bevel gear set. Bevel gear pitch diameters are measured on the outside face along the back-cone, as shown in the figure. As shown in figure 13-35, the resultant force acts at the average radius of the gear/pinion. If the power transmitted by the pinion is 10 at 1,453 rpm, calculate the pinion tangent force in lbf. Cone distance A Face Pitch angle Pitch angle Back cone Uniform clearance Pitch diameter Da Back-cone radius, h
The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of 982 rev/min. The tooth numbers are: N2= 18, N3= 45, N4= 12, N5= 34 Teeth respectively. Calculate the speed of output shaft 'c' in rev/min. Specify a positive number with 2 decimals
The spur gear arrangement shown in Figure has a pinion (driver Gear A) that rotates at 700 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degree. Given the number of teeth as shown, determine: The pitch diameters of the idler gear. 50 teeth A -90⁰- B 80 teeth C 60 teeth
The Diameters of pulleys of belt drive and number of teeth on the gears 2 to 7 are indicated in the figure. Find the speed and direction of rotation of gear 7?
A bicycle's gear ratio is the number of times the freewheel turns for every one turn of the chainwheel (see figure). The back half of a bicycle is given. A line labeled "Freewheel" is pointing at the center of the rear wheel. A line labeled "Chainwheel" is pointing to the center piece connecting the two pedals. The table shows the numbers of teeth in the freewheel and the chainwheel for the first five gears of an 18-speed touring bicycle. The chainwheel completes one rotation for each gear. GearNumber Number ofTeeth inFreewheel Number ofTeeth inChainwheel 1 32 24 2 26 24 3 22 24 4 32 40 5 19 24 Find the angle through which the freewheel turns for each gear. Give your answers in both degrees and radians. (Round your answers to one decimal place.) gear 1 = rad= gear 2= ° rad= gear 3= ° rad= gear 4= ° rad= gear 5= ° rad=
Problem 2. A compound gear train as shown in the following figure, Gear 1 has 24 teeth and Gear teeth of diametral pitch of 4. Gear 3 has 30 teeth and Gear 4 has 50 teeth of diametral pitch of 3. Gear 1 turns 12 rpm in clockwise direction. 2 has 70 (a) Computer the speed and direction of the shaft carrying Gear 4. (b) Find the torque at Shaft c if the input horsepower at Shaft a is 50? Shaft b Shaft c Shaft a Gear 1 Gear 2 Gear 3 Gear 4
Figure shown below illustrates the gears in a speed-change gearbox used in machine tool applications. By sliding the cluster gears on shafts Band C, nine speed changes can be obtained as shown in Table given below. The problem of the machine tool designer is to select tooth numbers for the various gears (2 to 10) so as to produce a reasonable distribution of speeds for the output shaft. The gears 2, 6 and 9 are having 20, 25 and 50 teeth respectively. The input shaft speed is 450 rpm and the output speed can vary from 137 rpm to 580 rpm depending on the sequence of the gears. If the output speed obtained through the gear sequence 2-5-5-8 is 257 rpm and if the minimum and maximum number of teeth in the gear system are 20 and 50 respectively, (i) Suitable tooth numbers for the remaining gears (3,4,5,7,8 & 10)
An epicyclic gear train as shown in figure. Gear D has 65 teeth, gear C has 15 teeth and annular gear A has 120 teeth. Gears B and C are compound. If the annual gear A is fixed and gear D rotate 600 rpm, find the speed of arm. A B- D -C
Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 inches. The addendum equals the module, and the clearance equals 0.135 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles. Draw simple circles showing the diameters and the center distance. Complete solution and drawing is required.
Consider the gear train in the following figure. Assume the angular velocity of driving gear is Win = 1000 rpm. Find the angular velocity of driven gear (@out). Driving Gear 12 Tooth Linked by Shared Axle Driven Gear 60 Tooth 60 Tooth
An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.