Answered: A 200 V, 50 Hz a.c. supply is given to…

A 200 V, 50 Hz a.c. supply is given to capacitance of 25 micro F. If the supply is given, write the formula for the curmate of the capacitor and find the RMS current of the capacitor.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Related questions

Q: Two point charges, q1 = q and 92 = 3q, are 25 cm apart. They repel each other with a force of 2.7 N.…

A: Given data, Charges are given, q1=q, q2=3q Force F =2.7 N Distance between r = 25 cm = 0.25 m

Q: The open-loop transfer function of a discrete system is given by expression: Y(z) 1 U(z) z²z+0.5…

Q: Sketch the root locus of a unity feedback control system with forward path transfer function is…

Q: Capacitors are used after the converter toA. smooth out the DC current.B. suppress the noise.C.…

A: A converter is used to convert the input AC voltage into DC voltage. The capacitor is used after the…

Q: Find the result of the subtraction using 2’s complement method. A= 110101 B= 101000 a) A -B b) B - A

A: 2's complement of some binary number is got by adding 1 to the 1's complement number. All the…

Q: The circuit in Fig. P9.30 is operating in the sinusoi- dal steady state. Find io(t) if v,(t) = 25…

Q: 1- find he transfer function H(jw)= Vo(jw)/Vs(jw). 2- find the kind of the filter, center frequency,…

Q: 4 Difference between circuit breaker and fuse...

A: Circuit Breaker Definition: A Circuit Breaker is a switching device which also offer protection…

Q: For the below circuit, find io across the 24 ohms resistor. 40 ΩΣ + 10ΩΣ 24Ω{ v 30 Ω Σ... 8 A 36 ΩΣ…

Q: 5. When a power Pt is transmitted by an antenna, amount of energy incident on the target is given by…

A: The correct option along with the explanation is provided in the following section.

Q: The open-loop transfer function of a discrete system is given by expression: Y(z) 1 U(z) z²z+0.5…

Q: Q: AM transmitter send the signal VAM = 500(1+0.4sin3140t) sin(6.28x107) t. This signal is feed of…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: If a voltage of 20 V is applied to the coil of a relay with 50 turns and internal resistance of 1 n,…

A: Given data, Voltage V = 20 V Resistance R=1 Ω Number of turns N = 50

Q: Find the voltage VAB in the circuit shown in below? T10v 10Ω, Ак 2052²3 20Ω VAB. 30Ω УВ $4022

A: The above Wheatstone bridge is not balanced as, 1020≠3040 The voltage at terminal A is given the…

Q: d) By block diagram reduction method obtain the overall transfer function of the control system…

A: By using Block diagram reduction method calculation of overall transfer function of given control…

Q: If in an RC circuit, the capacitance is increased by 20% and the resistance, R, is increased by 10%,…

Q: Two concentric Gaussian surfaces encloses a charge. Which is correct? O The outer surface will have…

A: Gauss law : According to Gauss law electric flux passing through any enclosed surface is equal to…

Q: This equation H = Hmax Cs/(Ks + Cs) is known as the O Moser O Powell O Monod O Tessier equation.

A: This is predicated on the notion that the primary influences on growth rate are substrate transfer…

Q: If in an RC circuit, the capacitance is increased by 20% and the resistance, R, is increased by 10%,…

A: Given: In an RC circuit, Capacitance is increased by 20% Resistance is increased by 10%

Q: Find the voltage across the capacitor terminal at time 1 ms for the circuit below. www R 10 Ω |1 100…

Q: When connected to a 4-ohm resistor, a battery has a terminal voltage of 6.5V. If the open-circuit…

Q: Electrical Engineering. What is the function of MCB. Write two advantage and disadvantage of MCB

A: An MCB is a type of electrical switch that operates automatically to guard against overload or short…

Q: Multiply out and factor: (A + B)(A' + E) = Type your answer with no spaces.

A: Given Boolean expression, F=A+BA'+E

Q: Question # 1 a) A certain filter has the following transfer function. 1500 H(jw)= (jw+50)² Find the…

Q: A motor that draws 4.5 kilowatts from the power line and delivers 5 horsepower has an efficiency…

A: Given data, Power drawn Pin=4.5 KW Power delivered Pout=5 hp=5×0.746=3.73 kw

Q: a) i) The data inputs have a low value of 0 V and a high value of +5V for a DAC in Figure 2, If the…

A: Given parameters : DAC input - 0 and 5 V Number of inputs - 4 Resistance at A, Ra - 120 k ohm…

Q: A circuit has in series of electromotive force given by E(t) = 100 sin 60t V, a resistor of 2 Ω, an…

A: It is given that: Et=100sin60t Vr=2 ΩL=0.1 HC=1260 Fi0-=0=dq0-dt=q'0-=0 Aq0-=0 C

Q: what are the advantages of root locus? need of feedback ?

A: The root locus is a graph that displays the position of a system's poles (the roots of the…

Q: An EM wave progating in a certain medium is described by E = 49.9 sin(28.4 x 106t - 4.5x)az V/m…

A: Given, The EM wave propagating in a medium is E=49.9sin28.4×106t-4.5az V/m

Q: . Find the phasor representation of the following functions. Use Cosine as a reference A. 4 cos(2πt…

A: Given functions, A. ft=4 cos2πt-40° B. ft=2 sin 4π103t-40°

Q: A 400V, 3-phase Induction motor has input power of 14 KW and operates at power factor of 0.87…

A: Given data, A 400 V, 3-phase induction motor has Pin=14 kWcosϕ=0.87 laggingη=86% Two wattmeter…

Q: n and be able to transform an s-domain solution rcuits with 5Ω + 20 u(t) Vx 0.5 F не 0.2 Ux 10 a b…

A: We convert the given circuit into its s domain equivalent . As initial condition of the capacitor is…

Q: If the kinetic energy of a body about an axis is 9J and the moment of inertia is 2kg- m², then the…

A: Given data, Kinetic energy of rotating body KE=9 J Moment of inertia I=2 kg-m2

Q: A parallel RLC resonant circuit has a quality factor Q-80, and a resonant frequency of 200 krad's.…

Q: A field of strength 5 × 10 ampere turns / meter acts at right angles to the coil of 50 turns of area…

Q: Find VGS and VDS for the E- MOSFET in the figure shown. The Datasheet information is listed with the…

Q: 4-9. Consider the circuit of Figure P4-9 with R₁ = 10 kn and R, = 70 kn. If the unity-gain fre-…

A: For the given op-amp circuit calculation of closed loop 3-dB bandwidth. Given: Ri=10 kΩRf=70 kΩand…

Q: What is the shape of a cell in GSM?

A: The solution is provided in the following section.

Q: What is the wave's (a) amplitude, (b) wavelength MAA 3 4 5 6 7 8 9 0 D. (volts) -2 x (cm)

Q: A 3-phase transmission line consists of 2 cm radius conductors spaced symmetrically 3 metres apart,…

Q: "An infinitely long conductor is lying on x = 1, -infinity <= y <= +infinity, z = 0 (in meters). If…

A: Force per unit length= u* I1* I2/(2πd). Which gives 1st option as correct answer. When current…

Q: the length of a wire that is moving with a velocity 0.4m/s in a magnetic field of 8T, inducing a…

A: Given, A wire moving with velocity, v=0.4 ms In a magnetic field, B=8 T Inducing a voltage, e=20 V

Q: What is tungsten,CFL,led bulb... Which one save electricity and why

A: The endeavour to lower energy consumption by utilising fewer energy services is known as energy…

Q: pply LPF to eliminate the higher frequencies in 3*3 image using a 3*3 average filter, the image…

Q: A generator is supplying a load of 500 kW at a power factor of 0.8 lagging. If the power factor is…

Q: x[n] = {x[0] = 1,2}. Calculate the 2-point DFT X[k] of x[n].

A: The solutions Are given below.

Q: What is the shape of a cell in GSM?

Q: Consider the circuit in Figure Q.1(b). The frequency of the circuit is given 23 f = 50 Hz. Find: (i)…

A: The reactance of inductance and capacitance is given by Inductive reactance, XL = 2πfL Capacitive…

Q: eedback diversity and maximal ratio combining (MRC) are versity reception methods. As an engineer in…

Q: Determine the maximum power (in Watts) that can be transfered to the load RL- (Use 3 decimal places.…

Concept explainers

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.

Question

A 200 V, 50 Hz a.c. supply is given to capacitance of 25 micro F. If the supply is given, write the formula for the curmate of the capacitor and find the RMS current of the capacitor.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
the parallel connection of a resistor and a capacitor takes 0.6 A rms from a 120 V rms voltage source. Given the 0.7 leading power factor, find the resistance and capacitance at 400Hz.
A capacitor "C", an inductor "L" and a switch "S" are connected in series. When the switch is open, the plate to the left of the capacitor has charge "Qo". The switch is closed the load and current vary sinusoidally with time. Represent graphically the load "Qo" and the intensity of current "I" as a function of time "t", and explain why the current leads the load by a phase difference of 90°.
A pure inductance of 1.273mH is connected in series with a pure resistance of 30ohms. If the frequency of the sinusoidal supply is 5kH and the p.d. across the resistor is 6V. Determine the value of the supply voltage in across the inductance.
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
Find the capacitance if correct will upvote otherwise i will dislike...
A capacitor C is connected in series with a 400 resistor across a supply of frequency 60 Hz. A current of 3 A flows and the circuit impedance is 500. Calculate: (a) the value of capacitance, C, (b) the supply voltage, (c) the phase angle between the supply voltage and current, (d) the p.d. across the resistor, and (e) the p.d. across the capacitor. Draw the Phasor diagram.
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
A 20-ohm resistor and a capacitor are connected in series with a battery of 60 volts. At t = 0, there is no charge on the capacitor. Find the capacitance if the current at t = 5 seconds is 3/e^s amperes. Ans. 0.05 Farads
Acertain electric circuit has a resistor and a capacitor. The capacitor is initially charged to 100 V. When the power supply is detached, the capacitor voltage decays with time, as the following data table shows. Find a functional description of the capacitor voltage v as a function of time t. Plot the function and the data on the same plot.