A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location.

A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
2. A steel shaft rotating at 600 rpm is supported by two bearings as shown. E=30 Msi, d=1.0" (inch), L₁=24.0" (inches), L=42" (inches), W₁-50 lb, Neglect the weight of the shaft. "The design is acceptable." True ? Show details. or False Diameter d W₁
The 46-mm diameter shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. The pulleys C and D are subjected to the vertical and horizontal loadings shown in the figure below. (Figure 1)
4) Ball bearings support the rotating axle shown below at points A and D. The rotating axle is loaded by a stationary (non-rotating) force of F = 6.8 kN. In the drawing below, all dimensions are in mm, and all geometry changes (steps in the diameter shaft) have a fillet radius of 3 mm. The axle is machined from AISI cold-drawn steel with an ultimate strength of S_u = 690 MPa and a yield strength of S_y= 580 MPa. Calculate the safety factor at the 6.8 kN load and points B and C, which experience moderate bending moments with a geometric feature that causes a stress concentration. Determine the number of cycles to failure of this part. 30 -10 -250 32 B 6.8 KN 75 -38 100- с 125 10 35 D 30
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
The d = 12-mm-diameter solid rod passes through a D = 20-mm-diameter hole in the support plate. When a load Pis applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 13 mm. The rod head has a diameter of a = 29 mm, and the head has a thickness of t = 8 mm. If the normal stress produced in the rod by load Pis 225 MPa, determine (a) the bearing stress acting between the support plate and the rod head. (b) the average shear stress produced in the rod head. (c) the punching shear stress produced in the support plate by the rod head. Support Plate Hole diameter D P Rod Head d P a b-
Problem 1. A shaft with a diameter d = 60 mm must transfer a torque of 350 Nm by using a key joint. The key has the following standard dimensions: b x h x 1= 18 mm X 11 mm x 50 mm. Calculate the stresses.
3. A steel shaft 60 in. long has applied to it a 10,000 in-lb torque by a pulley located at the center of the shaft. A gear at the left end of the shaft applies 8000 in-lb of torque to the shaft while a gear located 9 in. to the left of the right end of the shaft applies 2000 in-lb of torque. Calculate the angular deflection of the shaft if the shaft is 2 in. in diameter for a length of 36 in. from the left end of the shaft and 1.5 in. in diameter in the remainder of the shaft. Neglect the effect of the keyways in the calculations. Ans. 0.424o
A shaft of diameter d is guided in rotation at A (bearing 1) and C (bearing 2) and carries two wheels supporting the indicated loads, The radius of wheel B is 200 mm, and of wheel D is 100mm. The shaft is made of steel. F2 = 6000 N. Dimensions are in mm. Calculate the diameter (mm) of the shaft considering an allowable stress of 270 MPa for a stress composed of bending and torsion.
4) The 1.5 in diameter shaft below is supported by a thrust bearing at A and a self-aligning bearing at B. The gear weights 100 lbs and supports a 400 lb load in the axial direction (+x-direction), a 2000 lb transmitted load (+y-direction), and 600 lb radial load (-z-direction). The pulley weighs 400 lb and supports loads in the +z-direction. a. Construct the V-M-N-T diagrams for the shaft. b. Determine the location on the shaft with the most severe state of stress. c. Sketch the Mohr's circle and find the principal stresses at that location. 6 in. -12 in. - 8 in. YA 400 lb 600 lb Gear 2000 lb 4 in. 1200 lb 200 lb D 8 in. Pulley
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m