A 3 kg disk shown is pin supported at its center. The disk is rotated from rest and attains a constant angular velocity of 15 rad/s. If the mass of the rope is negligible and the radius of gyration of the drum is 50 mm; Find out the angular acceleration of the drum, the tension in the rope, and the torque experienced by the drum

A 3 kg disk shown is pin supported at its center. The disk is rotated from rest and attains a constant angular velocity of 15 rad/s. If the mass of the rope is negligible and the radius of gyration of the drum is 50 mm; Find out the angular acceleration of the drum, the tension in the rope, and the torque experienced by the drum

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

Rover weight capacity 35 kilo grams (payload)Rover measurements:Wheel distance - 14.5 inches and 8.5 inchesRover platform size (width & length) 14.4 inches x 10.4 inchesHeight- 15.8 inches Water tank selectionMore or less 25 liters*For tank selection we need to justify the size with the center of gravity, proving that is themaximum dimension or liters of the tank because the center of gravity will be higher makingthe rover prone to topplingPump selection*Our sprayer design has two nozzles which splits using a tee splitter, we need to find thesize of the pump to obtain the same discharge rate of a normal sprayer. A normal sprayerhas a 12V pump and a pressure from 0.2 to 0.45 mpa (30-65 psi)The application rate of the main pesticide is 9.6 - 19.2 fl oz/A (Brigade Insecticide for sweetpotato)Thai was the initial deign where the water tank is above the battery and pump, but wechanged our mind, now it is the battery and pump above the waterBattery selection* once the size of the pump…
Q5: a hydraulic press is used to compact powdered samples. The device is made of two interconnected cylindrical chambers filled with oil if density psubscripto anc closed by two pistons. The small chamber on the right has diameter d and the large chamber on the left has diameter 5d. A lever is attached to the piston pushing down on the fluid in the small cylinder. The horizontal lever is hinged on the left, at distance L from the small piston, and a force of magnitude Fsubscript0 is applied vertically down at distance 2L from the hinge (Fig.5). You may assume that the lever and pistons have negligible mass. a. Determine the magnitude of the force Fin that the small piston exerts on the fluid in the small cylinder. Hint: you may consider that the lever is at rest in the horizontal position. b. Determine the pressure change applied to the fluid by the small piston. c. Determine the magnitude Fout of the force that the fluid applies to the large piston.
A. A car's body has mass 100 slugs. This mass is supported by the car's 4 shock absorbers. The shock absorbers are identical vertical linear springs. Complete a FBD of the car's body (this would not include the car's wheels, axels etc. just the car's body) Each spring is compressed 1.25 inches. Determine the spring "k" value. Answer: 644 lb/inch. Find the compression of each spring if 4 people, each with mass 6 slugs, get into the car, Answer: 1.55" ii. iii.
Problem: A 1-m diameter and 1.6-m height cylindrical drum is filled with a fluid whose density is 850 kgm/m3. Determine the following: Volume of the fluid in ft3. Mass of the fluid in lbm. Specific volume in ft3/lbm. Specific weight in lbf/ft3. Problem: 6.5 psig to MPaa 330 mm Hggauge to mm Hgabs and kPag Problem: Compute the height in feet of a high building if the pressure at the ground floor is 30 in Hg and at the top of the building is 28.5 in Hg. Assume that the density of air is 0.075 lbm/ft3.
Fluid Mechanics & Machinery Q-5b A fluid has specific gravity of 0.9. What is the value of specific weight? (Take g = 10 m/s²).
Please help me with this question. Im struggling with the forces
P1.) A closed cylindrical tank 1.5 m in diameter and 4 m long is completely filled with gasoline (sp.gr. = 0.82) and accelerated horizontally at 3 m/s². Find the total force acting at the rear wall and at the front wall of the tank. Find also the accelerating force on the fluid mass. Answer: 10.66 kN and F = 17.36 kN Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
Problem 1. Four Loko used to be an alcoholic, caffeinated drink on the market. The drink contains 8% alcohol and 8 mg/oz caffeine. If an average person (70 kg) continued to drink these cans, we would they be more likely to die from an acute caffeine overdose or alcohol poisoning first? How many 16 oz. cans could they drink before risking a 50% chance of death? 1 oz. 19.57 mL, density of alcohol-0.8 g/mL. (Answer alcohol, 25 cans).
Weighted piston type accumulator is shown in the figure below. If area=350 cm?, a lift of the ram =1130 mm. Calculate the capacity of the accumulator in terms of liters. Weighnea Accumulator The capacity of the accumulator in liters =
H.W: A hypodermic syringe contains a medicine with the density of water. The barrel of the syringe has a cross-sectional area (2.50x10-5) m2, and the needle has a cross-sectional area (1.00x10 8 ) m². In the absence of a force on the plunger, the pressure everywhere is 1.00 atm. A force F of magnitude 2.00 N acts on the plunger, making medicine squirt horizontally from the needle. Determine the speed of the medicine as it leaves the needles tip.
QV: a hydraulic press is used to compact powdered samples. The device is made of two interconnected cylindrical chambers filled with oil if density psubscripto anc closed by two pistons. The small chamber on the right has diameter d and the large chamber on the left has diameter 5d. A lever is attached to the piston pushing down on the fluid in the small cylinder. The horizontal lever is hinged on the left, at distance L from the small piston, and a force of magnitude Fsubscript0 is applied vertically down at distance 2L from the hinge (Fig.5). You may assume that the lever and pistons have negligible mass. a. Determine the magnitude of the force Fin that the small piston exerts on the fluid in the small cylinder. Hint: you may consider that the lever is at rest in the horizontal position. b. Determine the pressure change applied to the fluid by the small piston. c. Determine the magnitude Fout of the force that the fluid applies to the large piston.
A certain gas at 30 degrees C is subjected to a pressure of 200kPa abs. if it has a volume 35 L, compute the mass of this gas. Use gas constant. R=210 N-m/kg-“K.a. 0.11kg c.0.97kgb. 0.23kg d.1.12kg