answer altest fiv A 400-V, 50-Hz, four-pole, Y-connected, three phase induction motor is rated at 30 hp.The equivalent circuit parameters areStator resistance= 0.50 2, Stator Reactance= 0.95 2 , XM= 35 2Rotor resistance (referred to stator)= 0.38 2Rotor Reactance (referred to stator)= 1.15 eP(F&W or, rotational) = 350W, P(misc, or, stray) = 120W, Pcore = 320WFor 4.2% slip, find the followings.I. The Stator line current IL and the stator power factorII. The stator copper losses PSCLIII. The rotor power factor and The rotor frequencyIV. The air-gap power PAG or, PgapV. The power converted from electrical to mechanical form, PconyVI. The induced or, the developed torqueVII. The load or, the shaft torqueVIII. The overall machine efficiency, n

The Wye connects one end of each coil to the other, allowing the individual phases to be applied to…

A 400-V, 50-Hz, four-pole, Y-connected, three phase induction motor is rated at 30 hp The equivalent circuit parameters are Stator resistance= 0.50 2, Stator Reactance= 0.95 2 , XM= 35 N Rotor resistance (referred to stator)= 0.38 2 Rotor Reactance (referred to stator)= 1.15 P(F&W or, rotational) = 350W, P(misc. or, stray) = 120W, Pcore = 320W For 4.2% slip, find the followings.

A 400-V, 50-Hz, four-pole, Y-connected, three phase induction motor is rated at 30 hp The equivalent circuit parameters are Stator resistance= 0.50 2, Stator Reactance= 0.95 2 , XM= 35 N Rotor resistance (referred to stator)= 0.38 2 Rotor Reactance (referred to stator)= 1.15 P(F&W or, rotational) = 350W, P(misc. or, stray) = 120W, Pcore = 320W For 4.2% slip, find the followings.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
Write a summary ( point) about equivalent cricuit of three phase induction motor .
The efficiency of 3-ph induction motor. at (Is=4.5A, T=13 N.m, N=1333 rpm, Pph=864 watt ) is
Frequency of emf in the stator of a 8 pole induction motor is 50Hz and the rotor emf frequency is 1Hz. The motor speed is ................ Answer
A 110 V, 60 Hz, 6 – pole single phase induction motor 1/3 hp has the following equivalent circuit impedances: RI = 1.52 ohm, R2 = 3.13 ohm and x1 =2.10 ohm, x2 =1.56 ohm. Xm=58.2 ohm, The Friction, windage and stry losses =16W, the core loss = 35 W, For a slip of 0.05, calculation (a) input current, (b) power factor, (c) developed power, (d) output power, (e) speed (f) in put power (g) air gab power (h) T ind (i) T load 6) efficiency.
If a 4-pole induction motor has a synchro- nous speed of 1500 r.p.m., then, supply fre- quency is (1) 50 Hz 60 Hz (iii) (ii) 25 Hz (iv) none of the above
A freewheeling DC motor is driven with 1000 rpm and a nominal load torque of 80Nm. The field circuit resistance is 200 and the armature circuit resistance is 0.2 O. The field coils are fed with a zero degree transmission angle through a single-phase fully controlled converter connected to a single-phase 240V source. The armature circuit is fed from a single phase 400V source through another fully controlled converter. Magnetic saturation has been neglected, the motor constant is given as 0.8 V - s / A - rad. Assuming that there is no fluctuation in armature and field current, find the control angle of the converter feeding the armature at nominal load. If you want to leave the question blank, click again on the option you marked.
A value of magnetizing current in a 3-phase induction motor * gives power factor smaller .. larger smaller. .poor large . better O large...poor O
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
A 3 phase, 400-V, 50 Hz 4 pole induction motor is fed from a 3-phase supply and runs of 1425 rpm. The frequency of the rotor emf is.....
Why do we need to have brushes in a squirrel-cage rotor type induction motor? (short answer)