DEGREE: ELECTRICAL ENGINEERINGSUBJECT/COURSE: AC CIRCUITS NOTE: Please solve in this way.Please have a good handwriting, some of the answers are not readable. Thank you!GIVEN. (Include symbols and units)ILLUSTRATION (Required).Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possibleFINAL ANSWERS must be rounded up to three decimal places with underlined twice A 400V, 3 - phase, 4 wire, star - connected system supplies three resistive loadsof 15kW, 20kW and 25kW in the red, yellow and blue phases respectively.Determine the current flowing in each of the four conductors.

In this question, 3 phase 4 wire system is given. If each phase power is given for only resistive…

A 400V, 3 - phase, 4 wire, star - connected system supplies three resistive loads of 15kW, 20kW and 25kW in the red, yellow and blue phases respectively. Determine the current flowing in each of the four conductors.

A 400V, 3 - phase, 4 wire, star - connected system supplies three resistive loads of 15kW, 20kW and 25kW in the red, yellow and blue phases respectively. Determine the current flowing in each of the four conductors.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Related questions

Q: EX :(9):- Consider a noiseless channel with a bandwidth of 3000 Hz transmitting a signal with two si...

A: a. The maximum bit rate is the Nyquist bit rate and is given by the expression as shown below: Bit...

Q: Build CMOS circuit using Truth-table method: a) F = a + b + c b) F = abc

Q: 18/ A 4-poles, 3-phase, 50 Hz induction motor is running at full-load at 1400 r.p.m. the star- conne...

Q: A half wave rectifier develops 10 V dc. What is the value of the ripple voltage? Vr(rms)=Blank 1 V

A: Ripple voltage = sqrt (rms voltage 2- average voltage2). For half wave rectifier average output volt...

Q: Question 1 a) With the aids of a diagram, briefly explain how an N-channel JFET being constructed an...

A: Solution (a) - N-channel JFET - A N-Channel JFET is a type of JFET in which the charge carrier is...

Q: T or F, modify the wrong part if False, please underline twice your answer if True or False. For a...

A: Total copper losses in shunt wound machine is sum of the armature copper losses and shunt field copp...

Q: The following page of the data sheet, contains 74138 function table. Study the function table. Given...

Q: Compute for the equivalent resistance of the circuit 50 a o- ww ww 5Ω 3Ω 10 0 ww wwww 40

A: If two resistors R1 and R2 are connected in series than equivalent resistance is R1 +R2. If two res...

Q: Define the Signum function.

A: It is an odd function f(x) = f(-x)

Q: R4 R3 Vo OA1 + R2 R1 RL VL + Vin

A: Use virtual ground concept.

Q: 20x ix 10 2 8 A 12 8Ω VB Vc VA 1 )1A 5Ω. + +

Q: Vc 5AE K9AE IREF I copy 3AE P 2AE

Q: Herdals Graph he allowing funshons and bad their Laplace transform ーラー (1))

Q: Determine the bandwidth and baud for an FSK signal with mark frequency of 32 kHz, a space frequency ...

A: Given, For an FSK signal, Mark frequency (f1) = 32 kHz Space frequency (f2) = 24 kHz Bit rate (Rb) =...

Q: a e pamp beed arence ampiter shon beo. e vas of R,RRndR • 1evand 20. teev. * 20v.andyt ang a erv.

A: Operational amplifier Basically an op-amp is a very high gain DC amplifier designed to provide low i...

Q: Consider a 3-bit ADC and full scale voltage measurement range of (0-56) The Resolution will be O 7.0...

A: Given: A ADC having, Number of bit, n = 3 Full scale voltage, VR=56 V

Q: A three-phase double circuit line is composed of ACSR Drake conductors arranged as shown. Calculate:...

A: We are authorized to answer three sub-parts at a time, since you have not mentioned which part you a...

Q: Find Rab in the circuit shown.

Q: 1. The circuit below has the following specifications: C1 = 10 mF, C2 = 30 µF, C3 = 250 mF, C4 = 80 ...

Q: 12 V 2 mA RC RB 7.6 V VB VCE B = 80 02.4 V RE FIG. 4.123

A: The solution is given below

Q: A cable has a VSWR of 10. If the minimum voltage along the cable is 20 volts, what is the maximum vo...

Q: 20 V 102 Si Si Si 12 V 102 10 V 102 202 (a) (b) (c) FIG. 2.155 Problem 5.

Q: onsider the circuit shown below. +12 V Rc 1.2 kn 1 µF HE C2 R1 12 kn Vout Vin 1 uF HE RL 600 n Rs 50...

Q: Question No.5 A current transformer has a phase error of +5 degree. The phase angle between the prim...

A: Given: A current transformer has, Phase error, θ=+5°

Q: Question 4 a) Simplify the circuit in Figure Q3 into a circuit (with clear labels) with only two ele...

Q: Sketch output waveform the following CLIPPER circuits. Pl

A: Given clipper circuits and input sinusoidal waveform with amplitude 8v and -8v then the output wave...

Q: Find the equivalent inductance of the circuit shown in the figure. 0.06 H u 0.04 H 0.06 H 0.06 H u

A: Given circuit,

Q: Ic(mA) 110 µA 100 μΑ 90 µA- 10 -80 μΑ. 70 μΑ 8 60 μ. 50 μΑ 40 μΑ. 30 μ. 3 20 μΑ 10 µA 10 15 20 25 30...

Q: A cylindrical rotor machine connected to an infinite bus bar is delivering active power of 1,1 p.u. ...

A: Given that active power (P)=1.1 pu. Reactive power(Q)=0.3 p u. ...

Q: An isolated turbine-generator is connected to two loads of 8 MW, each operating at 50 Hz. The turbin...

A: The solution is given below

Q: 3. Consider a three-wire Y-Y circuit. The voltages of the source are Van V3 o Vrms, Vin V3 <- 208 12...

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you ar...

Q: circuit is built around a bi-polar NP?N transistor. The Base network has a resistor (RB) and diode (...

Q: Also, express the signum function in terms of the unit step function.

A: In this case, the signum function needs to be defined and then its relation with the unit step funct...

Q: *9. Determine Vo, and Vo, for the networks of Si 4.7 kN Ge Si 1.2 k2 +12 Vo ,Voz -10 Vo- GaAs 3.3 kN...

A: Part (a) - The circuit diagram is shown below, We know,Vsi = 0.7 VandVGe =0.3 VConsider that the S...

Q: • T or F, modify the wrong part if False, please underline twice your answer if True or False. ...

A: Transformer is a two winding device and works on mutual induction . When primary winding is excited ...

Q: the fellowing sing appreach. 8olve block diagram raduction. G2 (S) RCS) G. (5) C.CS) = S Ca(5) = 35 ...

A: Given:

Q: For the circuit shown, a) Determine the load impedance that will result in maximum average power bei...

A: Maximum power theorem: This states that in the circuit load resistance is equal to the source resist...

Q: The armature resistance of 220V shunt DC motor is 0.4 takes load armature of 2A and run at 1350 r.p....

Q: iii. How much current will enter the branch BE? Here R3 and R5 are in parallel so, R3|| R5=3.3/2=1.6...

A: Brief description : In the above given question they want to know the value of current flowing in BE...

Q: 20 V Si 12 V Ge Si GaAs 4.7 k2 2.2 k2 4 V (a) (b) FIG. 2.160 Problems 10 and 50.

A: The solution is given below

Q: +Vcc Vin o V V. Vref VN Ry -Vcc RxL Figure Q.A2(e). Inverting Schmitt-trigger circuit. (ii) The oper...

A: Brief description : The given circuit is a Schmitt trigger circuit and we come to know that there ex...

Q: Determine I, V,, V2 and Vo for the following circuit. 1.2K V1 V2 :4.7K Si +2V

Q: 2-2 6-2 to Isv 3 t. 17.5 Turn on the circuit and find t = 1, t = 2, t = 3, t = 4, t = 5

Q: a. What is the peak value of the waveform? b. What is the peak to peak value of the waveform? c. Wha...

A: One division in x axis is equal to 1 m sec and one subdivision is 0.2msec One division in y ax...

Q: From the following figure find the value of VCE: Vcc = 13 V Ic = 7 mA Rc = 82 2 RE = 20 Q Vcc Ic RB ...

Q: 9. What is the electric field between two parallel metal plates separated by 2.5 cm with a potential...

A: Electric field between the parallel plate capacitor is pottential/ distance between the plates.

Q: In the given circuit, Vx = 6.5 V and Rx = 50. R 0.1V 3.32 V2 Referring to the given circuit, determi...

Q: he Norton equivalent circuit as seen by R,? Note that your answer should NOT be in ems of the unknow...

Q: State the purpose and value of the coefficient that relates to the conversion of power output which ...

A: Given that the purpose and value of Betz limit needs to be discussed in detail.

Q: Question. Find Vy, V, and V, in the circuit below if V, = 9 V. Assume an ideal op-amp. 50 ka 20 ka V...

Question

DEGREE: ELECTRICAL ENGINEERING

SUBJECT/COURSE: AC CIRCUITS

NOTE: Please solve in this way.

Please have a good handwriting, some of the answers are not readable. Thank you!
GIVEN. (Include symbols and units)
ILLUSTRATION (Required).
Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible
FINAL ANSWERS must be rounded up to three decimal places with underlined twice

A 400V, 3 - phase, 4 wire, star - connected system supplies three resistive loads
of 15kW, 20kW and 25kW in the red, yellow and blue phases respectively.
Determine the current flowing in each of the four conductors.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Mathematical Modeling of Mechanical System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question: How do the secondary voltage and current react to the different types of load and how do they behave within the secondary load circuits? Answer:
A 33 kV, 50 Hz. 3-phase underground cable, 6 km long uses three single core cables. Each of the conductor has a diameter of 2.75 cm and the radial thickness of insulation is 0.4 cm. Determine (1) capacitance of the cable/phase (ii) charging current/phase (iii) total charging KVAR. The relative permittivity of insulation is 3.
Discuss the arcing phenomenon in a circuit breaker. Please write more answer
A 400V, 3-phase, 4 wire, star - connected system supplies three resistive loads of 15kW, 20kW and 25kW in the red, yellow and blue phases respectively. Determine the current flowing in each of the four conductors.
Q1. In a 3-phase 4 wire, 400/230 system, a lamp of 100 watts is connected to one phase and neutral and a lamp of 150 watts is connected to the second phase and neutral. If the neutral wire is disconnected accidentally, what will be the voltage across each phase? Do you think it will affect their performance? Explain
Course: Electrical Engineering Subject: Electrical Apparatus Instructions: Write the GIVEN with their respective symbols and units. Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units • Round up to 3 three decimal places the FINAL ANSWERS and BOX it. Problem: A 400V, 3 - phase, 4 wire, star resistive loads of 15kW, 20kW and 25kW in the red, yellow and blue phases respectively. Determine the current flowing in each of the four connected system supplies three conductors.
Course: Electrical Engineering Subject: Electrical Apparatus Instructions: • Write the GIVEN with their respective symbols and units. • Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units • Round up to 3 three decimal places the FINAL ANSWERS and BOX it. Problem: Three generators connected in parallel are rated as follows: Generator 1: 100 MVA, 33 kV, reactance = 10% Generator 2: 150 MVA, 32 kV, reactance = 8% Generator 3: 110 MVA, 30 kV, reactance = 12% Choosing 200 MVA and 35 kV as base quantities, compute per unit reactances of the three generators referred to these base quantities.
ii) A string of suspension insulators consists of three units if the voltage across the line unit is 20 kV. The ratio of self-capacitance to shunt capacitance of each unit is 6:1. Determine a) V1 Answer for part 1 b) V2 Answer for part 2 c) VPh Answer for part 3 d) %String Efficiency Answer for part 4
Two persons are standing near a HV equipment and working on it, when an arc flash occurred. Person A was directly in front of the equipment and he managed to move out within 5 msec of arc flash, whereas Person B was standing at 30 deg from the equipment and moved out in 8 msec. Who do you think will be seriously affected and why?
A load that draws 12A is located 275 feet from its 240VDC source. It is supplied by aluminum conductors with a diameter of .092 inches operating at 75°C. What is the resistance of one conductor? [Answer is 10 ohms] Using the answer from this question, what is the voltage dropped across the load?
A current is measured at the neutral ground of a star load, of equal impedances in all three phases. Which of the following conditions is NOT possible?A) The currents in the three phases are equal in magnitude and angle.B)One phase of the supply conductors was left in open circuit.C) The line-to-neutral voltages in the load are equal in magnitude and with 120° phase shifts between them.D) None of the above
Load in Figure 1 needs to be connected to Mains Switch Board (MSB) using multicore PVC cable. As a maintenance engineer, you need to proposed cable size for the load, Determine the following issues. 1) Calculate current demand for the circuit. 1) Detemine suitable MCCB (Model and nominal current rating) should be used to protect the load against over-current. im Propose suitable cable size for the load in Figure 1. iv) Calculate voltage drop of the proposed cable WITHOUT consider the cable reactance and voltage drop correction due to higher cable operating temperature v) Calculate voltage drop of the proposed cable BY consider the cable reactance and voltage drop correction due to higher cable operatıng temperature vi) If the multicore PVC eable is change into 3 single core PVC cables, what the suitable cable size. All other multicore cables not available. (25 + variable x) m (A) 30 m (B) (15 + variable b) m (C) Multicore PVC cable MCCB 95 kW. (400 + variable y) V. 0.85 p.f. Load MSB…