A 6 pole, delta connected three-phase alternator having 144 slots is wound using double layer lap coils having 7 turns per coil. The coil has 16 / 24 pitch. The flux per pole is 7380000 maxuells. If the alternator is driven at a speed of 700 rpm, determine the total line-to-line generated voltage.

A 6 pole, delta connected three-phase alternator having 144 slots is wound using double layer lap coils having 7 turns per coil. The coil has 16 / 24 pitch. The flux per pole is 7380000 maxuells. If the alternator is driven at a speed of 700 rpm, determine the total line-to-line generated voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 14. For the RLC circuit shown L₁ 103mH, R₁ = 13602, C₁= 16.7μF, Em = 6.78V, = L₂= 203mH, R₂ = 10002,…

A: Given Data:An RLC circuit with,Input peak voltage Supply frequency To Find:The expression of .The…

Q: Calculate the required Q of a filter to convert DSB to SSB, given that the two sidebands are…

A: We are given,Wherefc= Carrier frequencyΔf=sideband seerationS=sideband supression

Q: Find the node voltages & calledor current. Which Region is the BJT operating in? -15/02 5105 P=100…

A: The question is about finding node voltages, collector current and operating region of the…

Q: There is no energy stored in the capacitor at the time the switch in the circuit makes contact with…

A: For the given RC based operational amplifier circuit the time at which the circuit becomes…

Q: It is known that G(s) and the closed-loop structure is shown below: R(s) (7 K(s+2) s(s + 1)(s + 4)'…

A: In this question, we need to determine the range of K for which the closed loop system will yield a…

Q: Question 25 Think of a way to re-wire the electrical system of this old automobile (with 6-volt…

A: Given circuit is,

Q: What are Instrument Transformers? Show on a prope diagram how the primaries and secondaries of both…

A: instrument transformer :-it is a highly accurate class electrical devices .they mostly used to…

Q: Q2. The differentiator above is used to amplify a sinusoidal input at a frequency of 1 MHz by a…

A: Given:a circuit, above circuit is amplifying input an signal by a factor of 5 at a frequency of 1…

Q: Question #2 Given the following series circuit R₁ R₂ 100 92 300 Ω 9 V R3 ww 50 Ω Calculate the…

Q: 100 k VG I 200 k WWW 9 V + 1 5 K VouT VIN

Q: (c) Figure Q3(c) shows an E-MOSFET biasing circuit. R₁ R₂ tur VDD R₂ Figure (3(e) Explain briefly…

Q: Consider the pole-zero plot shown in the following figure: a) Does it represent an FIR filter? b) Is…

A: We have the pole-zeros figurea) Does it FIR filterb) It is a linear phase system

Q: (c) Your friend Lynn Year looks at this circuit and says this can be modeled as a voltage controlled…

A: According to the question, for the given circuit as shown belowWe need to find the value of…

Q: A 460-V, 25-hp, 60-Hz, four pole, Y-connected induction motor has the following impedances in ohms…

A: The objective of the question is to find the speed, stator current, power factor, Pconv and Pout,…

Q: Build the OR gate and label the inputs and outputs. This needs to be done in Logism, or can be hand…

A: The OR gate truth table needs to be derived and the same has to be designed in the logisim…

Q: For the circuit shown in 2, if the power dissipated in R₂ is compared to an ideal network with R₁ =…

A: We need to find out power dissipation in R2 for given circuit.

Q: Answer: For the following state table, complete the timing trace for the state q as far as you can.…

Q: late the current across the capacitor shown in Fig. P8.6 if the voltage input is v1(t)-50 cos…

A: Given Data:A capacitive network with,Input voltage Capacitor Angular frequency To Find:The capacitor…

Q: B. Derive an expression for the lower and upper threshold voltages of Schmit trigger. Sketch the…

Q: 3. The circuit shown below is a coupled LC oscillator. VIN is an AC voltage represented by VIN(jo)…

A: In this question, we need to determine the network function N(jw) of the given function. We solve…

Q: 2. Consider the timing diagram in Figure P1 below Assuming that the D and Clock inputs shown are…

A: The circuit is given by The timing diagram is given byWe need to draw the output waveforms for Qa,…

Q: 50v Find 2052 ? ? Lc (t) ? T = RC Vects v8 w ¿ 2=72²3 20 Ec(t = ∞0) ? teo czam F

Q: If the total resistance of the circuit is 124 ohms, determine the value of R₁, given: R₁ = 124, R₂ =…

A: Given an electrical circuit with the following data:asked to find the value of R1.

Q: Please give me a complex Non-Inverting Amplifier circuit.

A: According to the question, we need to discuss a complex example of a non-inverting amplifier.

Q: 26. (a) A plane wave at 24 MHz, traveling through a lossy material, has a phase shift of 1 (rad/m),…

A: this ia a question of uwave

Q: = 5. A 1-phase, 25 kVA, 2300/230 V transformer has the following parameters: Zeq,H= (4.0 + j5.0) 2,…

A: We have,Singlephase ,25kVA,2300/230V Transformer has parameterCalculate the worst-case voltage…

Q: 1. For the circuit below, Vi(t) = 10cos(500t), R₁-502, R2-10092, C-47μF and L=50mH. Find the current…

Q: Given the following series circuit + 30 V- 2002 R1 R3 40 Ω R2 30 Ω Calculate the current I of the…

A: In this question, we need to determine the current I and voltage across the resistance R2 as shown…

Q: R(s) Answer: T(s) G1(s) G₂(s) G3(s) G4(s) G5(s) G7(s) G6(s) C(s) G6 G4+G6 G3+G6 G5 G3 + G6 G5 G₂…

A: In this question, we need to determine the transfer function. We solve this problem using Mason gain…

Q: 3) The circuit below shows resistors, inductors and capacitors, connected in series and in parallel.…

A: Given Data:An RLC circuit with,AC supply voltage Supply frequency Resistors Inductors Capacitor To…

Q: 2- Determine io(t) in the circuit given below. (2 io 25 cos(4 X 10³) V 2 ΚΩ 2 μF 0.25 H 10i,

A: In this question, we need to determine the current io(t) as shown in the circuit. We know,…

Q: If the total power is 450 kW in a power measurement of a 3- Phase delta connected load by 1-…

A: Total power is given as, P = 450 W.

Q: 1. Us 12052 €400. M 202 I tas f 300P +1, U₂ Find the transfer function H(s) = Vo(s) Vs(s)

A: In this question, we need to determine the transfer function. We solve this problem using the…

Q: It takes 255 cal to raise the temperature of a metallic ring from 20\deg C to 30\deg C. If the ring…

A: Answer:— Given that,, and ∆T = 30°C - 20° C = 10 °C.Substitute these values into the formula to find…

Q: Simplify the following logic function using Quine-McCluskey method (tabulation method). Then draw…

A: The given logic function is F(A,B,C,D)=Π(0,2,3,5,7,11,15) & 1,9,10 are don't cares. (Max terms…

Q: Problem 3: Question Consider the circuit diagram below. Given IA = 2.5 mA and Is = 1.25 mA: a) Find…

A: The given circuit isIA=2.5 mA.I8=1.25 mA.We need to determinea. The currents Is2, I2, I3, I4 and…

Q: Find the Thevenin equivalent circuit at terminals a - 30 92 120/45° V+ 01 60 92 = www Vth Vn 402 V,…

Q: A T-pad attenuator is an attenuator network consisting of three non-inductive resistive elements…

A: The given circuit isWe need to find the current through resistor R6 using Norton's theorem.

Q: Please ASAP

A: The objective of the question is to calculate the specific heat of the metal. The specific heat of a…

Q: Find the current in the mian branch and V. AB

A: According to questions, we need to calculate main branch current and V.AB.

Q: Problem 3 The DC load line and point Q of the circuit in figure (a) are shown in figure (b). For the…

Q: What is the total current for the circuit in the figure below? Given: R = 3000 Xc= 150 120 v 60 Hz…

A: The circuit diagram,The resistance, The capacitive reactance,

Q: The circuit of Fig.1 is governing by the "integrodifferential" equation. Use the Fourier transform…

Q: Problem 3: kn' = 500μA/V², V₁=2V, L= 10μm, W = 10μm, and λ = 0 (a) IG (b) (c) Vs= ID= +5 V 100 ΚΩ…

A: We need to find out current and voltage for the given circuit.

Q: 1. 2. 3. 4. 5. In Rn Eth Rth VL(Min) VL(Max) IL(Min) IL(Max) R₁ max pwr

A: The given circuit isWe need to find Eth and Rth.In and Rn.VL(min) and VL(max).IL(min) and IL(max).RL…

Q: Question #10 Given the parallel circuit presented below calculate the Equivalent Resistance Req when…

Q: Under steady-state DC conditions, find i and u in the circuit. 25 V + 15 Ω www 10 Ω www 10 F H|F +…

A: We need to find out current and voltage for the given circuit.

Q: common-base An NPN BJT with a = 0.93 is used in a amplifier configuration and is biased such that lc…

A: The question is about finding voltage gain ( Gv ) for a common base amplifier.

Q: 2. The output of a 20 km fibre-optic cable is measured at 0.005 mw. What is the input power if the…

A: Output power = 0.005 mW Fibre loss = 0.5 dB/km Total length = 20 km Input power = Pin = ?

Q: ain the fundamental loop equations associated with the tree branches {1, 2, 3, 7}. (b) Write the…

A: Bahggg

Concept explainers

Synchronous Generator

In comparison to an asynchronous generator, it is a machine where the rotor speed is equal to the rotating magnetic field produced by the stator, i.e., mechanical speed is equal to the electrical speed, thus called synchronous, and not asynchronous.

Salient Pole Rotor

Salient pole rotor includes a large number of exposed poles mounted on a magnetic wheel. The construction of a bright pole is as shown in the image on the left. The proposed poles are made of metal laminations. The rotor winding is provided on these poles and is supported by pole shoes.

Question

A 6 pole, delta connected three-phase alternator having 144 slots is wound
using double layer lap coils having 7 turns per coil. The coil has
16 / 24 pitch.
The flux per pole is 7380000 maxuells. If the alternator
is driven at a speed of 700 rpm, determine the total line-to-line
generated voltage.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

There are 144 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 1500 electrical and the flux per pole is 0.05 Weber sinusoidallly distributed. Calculate the emf induced per phase.
1.) A 6-pole, 3-phase, 60-Hz alternator has 12 slots per pole and four conductors per slot. The winding is 5/6 pitch. There are 0.025 Wb entering the armature from each north pole, and this flux is sinusoidally distributed along the air gap. The armature coils are all connected in series. The winding is wye-connected. Determine the open circuit emf per phase of the alternator. Subject Electrical machine 2
7. A 3-phase, Y-connected, 2-pole alternator runs at 3,600 r.p.m. If there are 500 conductors per phase in series on the armature winding and the sinusoidal flux per pole is 0.1 Wb, calculate the magnitude and frequency of the generated voltage from first principles. 8. One phase of a 3-phase alternator consists of twelve coils in series. Each coil has an r.m.s. voltage of 10 V induced in it and the coils are arranged in slots so that there is a successive phase displacement of 10 electrical degrees between the e.m.f. in each coil and the next. Find graphically or by calculation, the r.m.s. value of the total phase voltage developed by the winding. If the alternator has six pole and is driven at 100 r.p.m., calculate the frequency of the e.m.f. generated. [60 Hz; 11.5 kV] [ 108 V; 50 Hz]
A 3-phase, 16 pole alternator has a star connected winding with 144 slot and 10 conductor per slot. The flux per pole is 30 mWb sinusoidally distributed and the speed is 375 rpm. The frequency of generated emf is? Also find, the line emf is?
A 25cps single-phase, 8-pole, alternator with 725 mWb flux per pole has 288 slots. The machine coil has 2 turns per coil. In the winding of the armature, the ratio between the chording angle to the fractional pitch is 1/8. Find the voltage between two terminals.
Calculate the phase voltages of a three phase star connected 4 pole small alternator having a total flux per pole 0.30 Wb. Each phase has a concentrated winding of 10 full pitched turns and the relative velocity between armature winding and field flux is 1500 rpm.
A 3-phase 4-pole alternator has a single layer full-pitch winding with 8 conductors per slot. The armature has a total of 36 slots. Determine the voltage between lines when the alternator is driven at 1800 rpm with a flux of 0.05 Wb per pole.
A three-phase, 4-pole, 1,500 rpm alternating having a double layer-windings with 18 turns per coil. The slots per pole per phase are 10 and the coil span is 22 slots. The spread phase is 60 degrees and the flux per pole is 0.0625 Weber. If the armature windings are wye connected. a) Determine the generated voltage per phase and the line to line voltages. b) If the alternator is delivering a three - phase load of 1,200KW at 0.8 lagging power factor what is the line current of the alternator
8-pole 3-phase star-connected alternator with 144 grooves in its armature rotates at 900 rpm. There are 12 conductors in each groove in the armature of the alternator. The magnetic flux of one pole is 1.8.10 ^ 6 maxwels. Coils (1-16) were wound in -15 steps. Accordingly, find the phase and interphase voltages induced in the inductor of the alternator. (The speed of the alternator will be taken as synchronous speed ns.)
b) Explain the conditions of parallel connection of alternators and how these conditions are fulfilled.
13. A 3-phase, 16 pole alternator has a star connected winding with 144 slots and 10 conductors per slot. The flux/pole is 0.04 wb (sinusoidal) and the speed is 375 rpm. Find the frequency and phase and line e.m.f. The total turns/phase may be assumed to series connected. [50 Hz, 2035 Hz, 3525 V] (Rajiv Gandhi Technical University, Bhopal, 2000)
A 3-phase 4-pole alternator has 48 stator slots carrying the 3-phase distributed winding. Each coil of the winding is short chorded by one slot pitch. The winding factor is given by