A balanced 3-phase load is connected to a 230 V(rms)/50 Hz 3-phase power supply. If the total reactive power received by the load is 500 VARs at a lagging power factor of 0.8, what is the resistance in each phase of the load? (a) 152.4 Ω (b) 460.17 Ω (c) 115.04 Ω (d) 345.03 2 (e) None of the above

A balanced 3-phase load is connected to a 230 V(rms)/50 Hz 3-phase power supply. If the total reactive power received by the load is 500 VARs at a lagging power factor of 0.8, what is the resistance in each phase of the load? (a) 152.4 Ω (b) 460.17 Ω (c) 115.04 Ω (d) 345.03 2 (e) None of the above

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24P: A source supplies power to the following three loads connected in parallel: (1) a lighting load...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
A resistance of 20 Ω, an inductance of 0.2H and a capacitance of 100μF are connected in series across 220-V 50 Hz mains. Determine the following: a) impedance b) current c) voltage across R, L, and C d) power in watts and VA e) power factor and angle of lag.
Three-phase supply from utility The diagram shown in figure has two three- phase loads that form part of a manufacturing plant. They are connected in parallel and require 4.16 kV rms. Load 1 is 1.5 MVA, 0.75 lag pf A connected. Load 2 is 2 MW, 0.8 lagging pf, Y connected. The feeder from the power utility's substation transformer has an impedance of 0.4+j0.8 2/phase. Deter- mine the following: (a) The required magnitude of the line voltage at the supply. (b) The real power drawn from the supply. (c) The percentage of the real power drawn from the supply that is consumed by the loads. 0.4 Ω j 0.8 Ω 0.4 Ω j 0.8 Ω 0.4 Ω j 0.8 Ω m Load 1 am Load 2
An AC supply voltage is represented by v = 325 Sin wt. Three loads are connected in parallel across the supply, and the currents through these loads respectively are: 1=8.48 Sin wt 12 = 4.24 Sin (wt - 15°) 3 = 6.36 Sin (wt + 90°) Which of the following is the supply current? O a. 13.49 75°A O b. 9.63222.65°A O c. 19.08275°4 O d. 7.49275 A
5. The figure below shows two star connected loads with three phase power. The voltage source is 120Z0°. The loads are Z₁ = 10 + j4 № and Z₂ = 2 +j3 №. The cables are negligible. Calculate: a) the line and phase current. b) the real power from the source. c) the reactive power of the circuit. Is V N Z₁ Z₁ Z₁ Z₂ Z₂ N N Z₂
Question 4 For the circuit shown, what is the complex power, S, consumed by the load impedance? (Assume the voltage source is in RMS.) a 15 N V = 150 20° V 150 mH W = 300 rad/s O 1.58/18.4° kVA O 1.35/25.5° kVA O 530.3/45.0°VA O 474.3/71.6°VA Question 5 124
If a A-connected load has a balanced impedance ZA 94 - 17° 2 and a voltage = = / VBC = 265 82° V rms, what is the magnitude of the current Ia (in A rms)? C V cn Van a Answer: n Von b Ia Ib 20 B IAB IBC ZA ZA ICA C
A SINGLE-PHASE 230 AC, 60 HZ POWER SUPPLY FEEDS A 2400 WATTS AIR CONDITIONING SYSTEM, WITH A POWER FACTOR OF 0.5 IN LAGGING. IN PARALLEL WITH THE AIR CONDITIONING SYSTEM IS CONNECTED ANOTHER LOAD FORMED BY A 20 OHMS RESISTOR IN SERIES WITH A 40 mH COIL. DETERMINE THE TOTAL POWER TRIANGLEA) THE VALUE OF THE REAL POWER IS:B) THE REACTIVE POWER VALUE IS:C) THE VALUE OF THE APPARENT POWER IS: C) THE VALUE OF THE APPARENT POWER IS: CALCULATE ALSO THE VALUE OF THE CAPACITOR TO BE CONNECTED IN PARALLEL WITH THE SOURCE TO CORRECT THE TOTAL POWER FACTOR TO 0.96. EXPRESS YOUR RESULT IN MICROFARADSD) THE VALUE OF THE CAPACITOR IS:
For the circuit show below, solve for the following: a. The complex power delivered to each passive component of the circuit b. The total impedance c. The overall power factor j30 N -j25 N elll 50/-17° V rms 10 2 15 0
Five infinite-impedance voltmeters are calibrated to read rms values. The voltmeters read V1=30 volt, V2=90 volt, V5=60 volt. What is the power factor of the circuit? R L ele d V3 V4 Vs 1/3 O 0.5 O 1.5 O 2 О 2/3
A three-phase 400 V, 60 Hz delta connected load has three equal impedances each of (10+j50) Q2. What is the value of inductance?
A load is operating at unity power factor. Which of the following statements is FALSE? a) The apparent power is numerically equal to the real power. b) The current is in phase with the voltage. c) The load is purely resistive. d) None of the above. A load is absorbing 10 kW and -4.5 KVAR. Which of the following statements is TRUE? a) The load has a lagging power factor. b) The phasor voltage is leading the phasor current. c) The load may be modeled as a resistor in series with a capacitor. d) None of the above.