A beam with a Z cross-section is subjected to moment M, which has a magnitude of 20 kip in. The resisting moment Mr on the cross- section makes an angle a = 36.87° with the =- axis. The moments of inertia and product of inertia for the cross section are I = 8.83 in4, I = 25.4 in4 and Iyz = 11.3 in4. Determine the maximum tensile stress (in ksi) in the beam. Note: Write answer in 2 decimal places.

A beam with a Z cross-section is subjected to moment M, which has a magnitude of 20 kip in. The resisting moment Mr on the cross- section makes an angle a = 36.87° with the =- axis. The moments of inertia and product of inertia for the cross section are I = 8.83 in4, I = 25.4 in4 and Iyz = 11.3 in4. Determine the maximum tensile stress (in ksi) in the beam. Note: Write answer in 2 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the lightest S-shape for the beam shown if the working stress in bending is 120 MPa. What is the maximum bending stress in the beam selected? Lightest S-shape beam =Maximum bending stress (MPa) =
A bar having a cross-sectional area of 700 mm² is subjected to axial loads at the positions indicated. The value of stress in the segment BC is 21kN 63KN 35kN + 49kN A В (а) 40 MPа (b) 50 MPа (c) 70 MPa (d) 120 MPa
Q- A uniform prismatic circular bar made up of rigid material is subjected to a tensile force of 5000 N at one end. If the diameter of the cross-section is 7 mm, then find the stress and strain in the bar.
2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in Fig. 2-42. Through a fabrication error, the central bar, ②2, is 0.0005L too short. All bars are of identical cross section and of steel having E = 210 GPa. Find the stress in each bar after the system has mechanically been pulled together so that the gap A is closed. Ans σ-35 MPa σ = 70 MPa Fig. 2-42
with full solution please Determine the mass of the heaviest uniformcylinder that can be supported in the positionshown without exceeding a stress of 50 MPa incable BC. Neglect friction and the weight of bar AB.The cross-sectional area of BC is 100 mm^2.
Steel Tank with an outside diameter of 600 mm has a wall thickness of 8 mm. The tank is used as storage of gas under pressure of 2.2 MPa. a. Determine the value of the tangential stress in the tank wall Determine the value of the longitudinal stress in the tank wall b. 30 mm helt hand
Q- A stepped steel shaft is subjected to a clockwise torque of 10 Nm at its free end. Shear modulus of steel is 80 GPa. Find the strain energy in the shaft? A 50 mm dia 100 mm B 25 mm dia 100 mm C K T=10 Nm
Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is the maximum bending stress in the beam selected? Please answer this with FBD please. Thank you.
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
2.) When an axial load is applied to the ends of the bar shown, the total elongation of the bar between joints A and C is 0.15 in. Ing segment BC, the normal strain is measured as 1,300 µin/in. Determine: (a) the elongation of segment BC; (b) the normal strain in segment AB of the bar. A tuhe with R 10u106 ni i 11
Value of effective stress at point C
A high-density polyethylene [E = 121 ksi and a = 61 x 10-6/°F] block (1) is positioned in a fixture. The block is 2.2 in. by 2.7 in. by 29 in. long. At room temperature, a gap of 0.11 in. exists between the block and the rigid support at B. Determine: (a) the normal stress o in block (1) caused by a temperature increase of 98°F. (b) the normal strain & in block (1) at the increased temperature. [ Answerrs: (a) o = (b) = 0.11 in. 29 in. Ans: (a) - 264.3725 με. (b) 3793.1033 psi.