A belt drive consists of two v belts in parallel on a grooved pulley of the same size.the angle of the groove is 30°.the cross-sectional area of each belt is 750mm^2 and coefficient of is 0.22.the density of the belt material is 1.2Mg/m^3 and the maximum safe stress in the material is 7MPa. Calculate; (A) the power that can be transmitted between the pulleys 300mm diameter rotating at 1,500rpm (B) the speed of the shaft in rpm at which the power transmitted would be a maximum

A belt drive consists of two v belts in parallel on a grooved pulley of the same size.the angle of the groove is 30°.the cross-sectional area of each belt is 750mm^2 and coefficient of is 0.22.the density of the belt material is 1.2Mg/m^3 and the maximum safe stress in the material is 7MPa. Calculate; (A) the power that can be transmitted between the pulleys 300mm diameter rotating at 1,500rpm (B) the speed of the shaft in rpm at which the power transmitted would be a maximum

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.6P

See similar textbooks

Similar questions

Q A shaft rotating at 200 r.p.m. drives another shaft at 300 r.p.m. and transmits 6 kW through a belt. The belt is 100 mm wide and 10 mm thick. The distance between the shafts is 4m. The smaller pulley is 0.5 m in diameter. Calculate the stress in the belt, if it is . An open belt drive, and 2. A cross belt drive. (Take μ = 0.3)
Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 1650 and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted. 1 Add file
Two 400 mm diameter pulleys are keyed to a simply supported shaft 500 mm apart. Each pulley is 100 mm from its support and has horizontal belts, tension ratio being 2.5. If the shear stress is to be limited to 80 MPa while transmitting 45 kW at 900 rpm, find the shaft diameter if it is to be used for the input-output belts being on the same or opposite sides.
Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100 mm from its support and has horizontal belts, tension ratio being 2.5. If the shear stress is to be limited to 80MPa while transmitting 45 kW at 900 rpm. Find the shaft if it is to be used for the input - output belts being on the same or opposite sides.
3. The safe working stress of a belt is equal to the tight side tension over the product of the belt's width and thickness. Find the width of the belt if a 610mm diameter pulley transmits 40 kW at 500 rpm, the arc of contact is 144°, coefficient of friction is 0.35, safe working stress of the belt is 2.1 MPa and thickness is 6mm.
A belt drive consists of two V-belts in parallel, on grooved pulleys of the same size. The angle of the groove is 30°. The cross-sectional area of each belt is 750 mm² and µ= 0.12. The density of the belt material is 1.2 Mg/m³ and the maximum safe stress in the material is 7 MPa. (a) Calculate the power that can be transmitted between pulleys of 300 mm diameter rotating at 1500 r.p.m. (b) Find also the shaft speed in r.p.m. at which the power transmitted would be a maximum. (Answers: 172 kW; 2800 r.p.m.)
A V-belt drive consists of three V-belts in parallel on grooved pulleys of the same size. The angle of groove is 30° and the coefficient of friction 0.12. The cross-sectional area of each belt is 800 mm² and the permissible safe stress in the material is 3 MPa. Calculate the power that can be transmitted between two pulleys 400 mm in diameter rotating at 960 r.p.m.
A closely coiled helical spring is to carry a load of 500N. Its mean coil diameter is to be 10 times that of the wire diameter. Calculate these diameters if the maximum shear stress in the material of the string is to be 80MN/m^2.
A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is transmitted via the drive shaft, ABC. The section AB is a solid circular shaft 0.7 m long and the section BC is a hollow circular shaft 1.0 m long with 110 mm outer diameter and 55 mm inner diameter. Both shafts are made from a metal alloy (Shear Modulus G = 95 GPa). 0.7 m 1.0 m A в 2400 hp @ 2000 rpm Figure 3 a) If the drive shaft rotates at 2000 rpm and the power transmitted along the shaft is 2400 hp (1 hp = 745.7 W), calculate the torque developed in the drive shaft.
3) A flange coupling is to connect two 60mm shafts. The hubs of the coupling are 120mm, 100mm thick, & the flange webs are 20 mm thick. Six M16 bolts fasten the flange from a 165 bolt circle. The keyway is 15mm shorter than the hub’s thickness & the key is 15mm x 15mm. The coupling transmits 45kW @ 450rpm. The yield point in shear for all materials is half of its yield point in tension or compression. Yield tensile strength is 0.75 of ultimate strength of the materials. The Sult is 448N/mm2 . Find: (a) the shear stress in key; (b) the bearing stress in key; (c) the shear stress in bolts; (d) bearing stress in flange.
Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 165o and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted.
Questlon 4 The drive from a motor to a machine is by means of a crossed flat belt. The shat of the motor and the machine are parallel and 1.2 meter apart. The motor pulley A turns at 1440rpm and has a diameter of 250mm. The machine B rotates at 450rpm. The belt is made of lether. The safe tensile stress is 7MPA and the density is 900kg/m. The dimensions of the belt are 50mm x 6mm. p = 0.2. Dermine: The length of the belt required The maximum power that can be transmitted The maximum torque on the driving pulley The maximum torque on the driven pulley