A bracket plate is used to transfer the reaction of a beam to a column flange as shown in Fig. Ex. 10.9. The bracket plate is connected to the column flange by a 6 mm fillet weld. Compute the maximum load that can be placed over the bracket plates at a distance of 75 mm from the flange of the column section. P 75 mm XK T 100 mm O 100 mm 2P I 200 mm I.S.H.B. 300 @ 576.8 N/m Fig. Ex. 10.9 75 mm

A bracket plate is used to transfer the reaction of a beam to a column flange as shown in Fig. Ex. 10.9. The bracket plate is connected to the column flange by a 6 mm fillet weld. Compute the maximum load that can be placed over the bracket plates at a distance of 75 mm from the flange of the column section. P 75 mm XK T 100 mm O 100 mm 2P I 200 mm I.S.H.B. 300 @ 576.8 N/m Fig. Ex. 10.9 75 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.2.4P

See similar textbooks

Similar questions

Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).
A welded bracket connection is shown in figure. It supports a factored load of 150 kN at a distance of 120 mm from the face of column. Design the fillet weld on two sides. Grade of steel = Fe410, f. = 250 MPa. y 120 mm P₁ = 150 kN Fillet weld t = 12 mm
Plate is connected to the column using fillet welds as shown. The size of weld is 12 mm. Determine the following: Locate the center of gravity of the weld group from the vertical part of the weld. Stress due to moment. Max stress due to combined moment and load. 100KN 4 100mm 55mm 150mm 55mm 110mm 3
Two 75mmx8mm A36 steel plates are welded in a 10mm gusset plate. Assume a weld thickness of 7.5mm and that of electrode used is E70. Determine the following: 1. Total Length of weld if P=300KN 2. Load P based on block shear if L1=85mm and L2=92mm. Neglect end returns P -2-75mmx8mm plates 10mm-thk L1 gusset plate L2 end returns
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
Problem 14.3.A A 4 × 4 × ½-in. angle of A36 steel is to be welded to a plate with E 70 XX electrodes to develop the full tensile strength of the angle. Using %-in. fillet welds, compute the design lengths for the welds on the two sides of the angle, assuming development of tension on the full cross sec- tion of the angle. A=3.75 inch2 L1= 10.94" L2 = 5.09" IF only connected leg, L=7.7"; 4.75 each side
A steel plate is used to connect a column and beam as shown in Fig. 1. The connection for columnis fillet welds and the connection for beam is a group of bolts. Given Q=150kN and Mx= -5kN-m(applied at centriod of the bolt group), determine: (1) maximum shear force in bolts; (2)maximum stress in welds.
Tension Member Design Problem 1. A channel shape is under 50 kips dead and 100 kips live tensile axial load as shown in the figure. The member is connected to a gusset plate with 10 inch longitudinal welds. Find the lightest channel shape to carry the loading. Use only vielding and rupture limit states to design. Use 50 ksi steel (Fy=50 ksi, Fu=65 ksi). (a) Assume yielding limit state controls in the design process; (b) After selecting the lightest section, check the rupture limit state. Do not redesing if needed. 1 Pa=50 kips PL=100 kips 10"
S Example 8.7 An ISA 200x100x10 angle LO 3 is welded to a steel plate by means of fillet welds as shown in Fig. 8.17. The angle is subjected to a static force of 150 kN and the permissible shear stress for the weld is 70 N/mm². Determine the lengths of weld at the top and bottom. 1₁ 150 kN TAILL Y2 200 12 - IG 100- 12 71.8 150 KN -10
The double T-beam is fabricated by welding the three plates together as shown. Part A Determine the shear stress in the weld necessary to support a shear force of V=78 kN�=78 kN.
10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 10 MPа О 12.5 MPa 15 MPa 8.5 MPa O no one O ---.. O- O O 300mm 8 mm