A bullet weighing 0.5 kg is fired with a horizontal velocity of 650 m/s into the lower end of a slender 7 kg bar of length L=0.90 m. Knowing that h=0.4 m and that the bar is initially at rest, determine (a) the angular velocity of the bar immediately after the bullet becomes embedded, (b) the impulsive reaction at C, assuming that the bullet becomes embedded in 0.001 s.

A bullet weighing 0.5 kg is fired with a horizontal velocity of 650 m/s into the lower end of a slender 7 kg bar of length L=0.90 m. Knowing that h=0.4 m and that the bar is initially at rest, determine (a) the angular velocity of the bar immediately after the bullet becomes embedded, (b) the impulsive reaction at C, assuming that the bullet becomes embedded in 0.001 s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 18-kg rear hatch of a vehicle opens as shown in the figure and can be modeled as a uniform 0.6-m long slender rod. Knowing that the tailgate is released from rest in the position shown in the figure, determine the angular velocity of the tailgate as it impacts the car body. I have attached Solution Too, You can Refer It( There Mass=16 kg) In our Problem Mass=18 Kg That is Only difference.
A bullet of mass m is fired with a horizontal velocity v0 and at a height h = ½ R into a wooden disk of much larger mass M and radius R . The disk rests on a horizontal plane and the coefficient of friction between the disk and the plane is finite. (a) Determine the linear V1 and the angular velocity w1 of the disk immediately after the bullet has penetrated the disk. (b) Describe the ensuing motion of the disk and determine its linear velocity after the motion has become uniform.
A large 3-lb sphere with a radius r = 3 in. is thrown into a light basket at the end of a thin, uniform rod weighing 2 lb and length L= 10 in. as shown. Immediately before the impact, the angular velocity of the rod is 3 rad/s counterclockwise and the velocity of the sphere is 2 ft/s down. Assume the sphere sticks in the basket. Determine after the impact (a) the angular velocity of the bar and sphere, (b) the components of the reactions at A.
Consider a slender rod AB with a length l and a mass m. The ends are connected to blocks of negligible mass sliding along horizontal and vertical tracks. If the rod is released with no initial velocity from a horizontal position as shown in Fig.A, determine its angular velocity after it has rotated through an angle of θ (see Fig B) using the conservation of energy method. (Hint: Moment of inertia of rod about G = (1/12)ml2 The kinetic energy of a rigid body in plane motion is
A 1.8-lb javelin DE impacts a 10-lb slender rod ABC with a horizontal velocity of v0 = 30 ft/s as shown. Knowing that the javelin becomes embedded into the end of the rod at point C and does not penetrate very far into it, determine immediately after the impact (a) the angular velocity of the rod ABC (b ) the components of the reaction at B. Assume the javelin and the rod move as a single rigid body after the impact.
W = O rad 8 h A 1.4 m by 1.4 m thin plate is used as target practice at a firing range where participants are shooting for sport. If the plate has a mass of mplate = 16 kg and is pinned at point O, determine the angular velocity of the plate just after a 5 g bullet, shot at a velocity of Ubullet = 480, is embedded in it. The bullet hits a vertical distance h = 1.05 m away from point O. m S (CC BY UBC Engineering
14 in. 18 in. VB 1500 ft/s -18 in. A 0.05-lb bullet is fired into the side of a 20-lb square panel which is initially at rest. Determine a) the angular velocity of the panel immediately after the bullet becomes embedded and b) the impulsive reaction at A, assuming that the bullet becomes embedded in 0.0006 s. B
A locomotive consists of multi cylinder reciprocating engine running at a speed of 8 r.p.s having a stroke length of 29cm, which carries a mass of reciprocating part whose magnitude is 11kgs with a revolving part of 5kgs rotating at 17cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 500 from top dead centre to bottom dead centre. solve 4 and 5 1. Maximum primary unbalanced force of reciprocating mass in newtons 2. Balancing mass required at a radius of 41cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 76cm between the two cylinders in (N-m) 5. Magnitude…
A locomotive consists of multi cylinder reciprocating engine running at a speed of 4 r.p.s having a stroke length of 27cm, which carries a mass of reciprocating part whose magnitude is 14kgs with a revolving part of 5kgs rotating at 16cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 520 from top dead centre to bottom dead centre. 1. Maximum primary unbalanced force of reciprocating mass in newtons ) 2. Balancing mass required at a radius of 44cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 74cm between the two cylinders in (N-m) 5. Magnitude…
R B R с D The motion of a slender rod of length 0.545 m is guided by pins at A and B which slide freely in slots cut in a vertical plate as shown. If end B is moved slightly to the left and then released, determine the angular velocity of the rod and the velocity of its mass center (a) at the instant when the velocity of end B is zero, (b) as end B passes through Point D.
4) The homogeneous rod AB weighs 96.6 lb and is at rest in the vertical position when an impulsive blow of 6 lb-sec is applied at the end B of the rod. Determine.(a) The angular velocity of the rod after the impulse has been applied.(b) The time average force acting on the rod exerted by the horizontal component of the pin reaction at A if the im- pact time interval is 0.002 sec. Solve all questions using Impulse and Momentum methods
A bullet weighing 0.08 lb is fired with a horizontal velocity of 1800 ft/s into the lower end of a slender 15-lb bar of length L = 30 in. Knowing that h = 12 in. and that the bar is initially at rest, determine (a) the angular velocity of the bar immediately after the bullet becomes embedded, (b ) the impulsive reaction at C , assuming that the bullet becomes embedded in 0.001 s.